SOCAL: Local FS/FT

[Thunder86]

Originally Posted by Thunder86

WTS Work M.C.O. Racing Type CS 18x8.5 +38 (comes in Work “Blood Red”)

Wheels are wrapped in 245/35/18 Continental ExtremeContact DWS06

Set up will come with: OEM TPMS, Work license plate frames (2), Work M.C.O. wheel decal/sticker sheet, and a set of Kyo-ei Bull Lock Tuskey lug locks

Wheels were fully ceramic coated right out of the box. Wheels & tires have about 16k miles on them. Condition is 8/10 due to daily driving rash, however, they have never been curbed, tracked, autocrossed, etc.

Ran these with stock struts + TRD springs with -1.7 camber front and -1.5 camber rear... had ZERO rubbing issues and fitment is flush!

Links: https://www.ft86speedfactory.com/wor...l#.XgxZNySIaEc ... https://m.tirerack.com/tires/tires.j...06XL&tab=Sizes

This setup would cost about $2800 new. Would like to sell full kit for $1600 obo.

Local pick-up only for now.

Huge price drop! PM me with reasonable offers too!

[degozaru]

Originally Posted by MugsBRZ

Hi All,

Going back to stock and need the parts listed below for a 2012-16 BRZ. I assume FR-S parts would work fine, too. I'm looking for parts in good condition with 30k miles or less on them. I also have a lot of aftermarket parts that I would be willing to trade or I will pay cash. I would meet you or pay for shipping.
Thanks,
Daniel

interested in the sun shade and the trunk organizer, but where in cali are you

[EdBoy]

Originally Posted by MugsBRZ

Hi All,

Going back to stock and need the parts listed below for a 2012-16 BRZ. I assume FR-S parts would work fine, too. I'm looking for parts in good condition with 30k miles or less on them. I also have a lot of aftermarket parts that I would be willing to trade or I will pay cash. I would meet you or pay for shipping.

Thanks,
Daniel

Sent you a pm, I have quite a few stock parts laying around I need to get rid of.

Originally Posted by stlgrym3

RCE Yellow springs, ecutek cable & dongle, SPC rear LCAs for sale in temple city area. All in near new condition.

http://http://www.ft86club.com/forum...d.php?t=139300

http://http://www.ft86club.com/forum...d.php?t=139406

http://http://www.ft86club.com/forum...d.php?t=139407

Can't see the thread, but how much for the springs?

[stlgrym3]

Originally Posted by EdBoy

Sent you a pm, I have quite a few stock parts laying around I need to get rid of.



Can't see the thread, but how much for the springs?

$180 for the springs.

[zAnSh1n]

Brand new.

Front LCA ball joints: 020410 [gray]
https://racerxfabrication.com/frs-br...er-ball-joints

$120

[MJones_RB]

Originally Posted by zAnSh1n

Brand new, unopened boxes.
Bought them years ago, but ended up going the 'show' route instead.

Front: PSP-SUS-131 [22mm]
https://www.perrin.com/shop/suspensi...-front-swaybar


Rear: PSP-SUS-230 [19mm]
https://www.perrin.com/shop/suspensi...z-rear-swaybar


$250/set


---

Rear end links: 020406 [gray]
https://racerxfabrication.com/frs-br...rear-end-links


$60


---


Front LCA ball joints: 020410 [gray]
https://racerxfabrication.com/frs-br...er-ball-joints


$120

Nice deal!

[shiumai]

P3 Car OBD2 Vent Gauge for sale - $290 shipped (MSRP $389) paypal or venmo. Or, local pick up in North Redondo Beach (Los Angeles area).


http://www.p3cars.com/subaru/p3-v3-o...uge-2013-2019/
P3 Vent Gauge Readouts (all readouts can be individually configured to read in either Imperial or Metric units)

• Boost (through OBD2 port using OEM sensors or with P3 analog boost sensor)
• Engine oil temperature
• Coolant temperature
• Air/Fuel ratio (can be read in AFR or Lambda)
• Vehicle speed (can be calibrated in 1% increments from -9% to +20%)
• Intake air temperature
• Throttle angle
• Ignition timing
• Engine RPM
• Exhaust gas temperature
• Battery voltage
• Programmable shift light
• Analog input 1 (brown wire) can allow gauge to read any 0-5 volt linear output sensor
• Analog input 2 (blue wire) can allow gauge to read any 0-5 volt linear output sensor
• Acceleration timers (0-60mph/0-100mph/60-130mph)

Plug and Play - Easy installation into vent, then plug directly into OBD2 port under dash:
http://www.p3cars.com/content/pdf/brz-vent.pdf

[youngdriver94]

Stock wheels and tires from my 2016 scion frs. Just cleaned them up and put a coating of Chemical Guys Max Coat Wheel Guard on them. You can see in the pictures that they are in great condition and shining like new! Slight curb rash on some of the wheels but not too noticeable due to their color. I took these wheels off my car over 2 years ago when I got aftermarket wheels and they have been sitting in my garage ever since.

$300

I am located in San Diego but frequent the Inland Empire area as well, so I am willing to meet up in either area.

SOLD

[youngdriver94]

Stock headlights from my 2016 scion frs. Bulbs and everything still work. They were taken off my car over 2 years ago and have been sitting in boxes ever since. During their time on my car it was always garaged so there is no hazing, yellowing, condensation, or peeling. They are in great condition!

$200

I am located in San Diego but frequent the Inland Empire so I can meet up in either area.

Sold. Please Remove

[DarkSideFRS]

Looking for rear bumper in 37j.. let me know what u have

[FRS Johnny]

Looking for a complete engine. Mine blew up :/

[Rmikey009]

What's up everyone? I have a few used parts for sale that came with my '13 BRZ:


1) JDL UEL header - $600 O.B.O
2) A set of oem wheels 17 in'. Wheels come with tires, but the tires are pretty worn. $250 O.B.O
3) OEM exhaust - $150 O.B.O


I've been having trouble uploading any pictures so please feel free to text me for pix of the parts that you're interested in. 562-332-4740. Parts are located in Whittier, Ca 90603. My name is Mike. Thanks everyone!

[Huevo_blanco]

For sale
Location : Long Beach Ca 90802
Selling - FR-s bayson R ST-style front lip and bayson R Cs- side splitters both used 8/10 no cracks nothing is broken
Please pm and I’ll sent you pictures
Price : SOLD each or take both for SOLD

[John Rambo]

For Sale: KW v3 coilovers. I am the second owner. They have been in my garage for a while and I want them gone. Asking $750.

Local pickup in los angeles strongly preferred