WHAT DID YOU DO TO YOUR FRS TODAY? - Page 1304 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

dnieves · 02-04-2018, 01:05 PM

Quote:

Originally Posted by Slushboxr

Then I'm off to a good start haha

Sent from my iPhone using Tapatalk

Whatever you run over is going to end up sliced. Where are the pre-existing mounting points or will you have to make your own and drill?

Slushboxr · 02-04-2018, 02:23 PM

Quote:

Originally Posted by dnieves

Whatever you run over is going to end up sliced. Where are the pre-existing mounting points or will you have to make your own and drill?

Haha I'm actually gonna round the edges more and put a trip around it so the ends aren't bare. Two existing from the sway bar and two into the bash bar. When I put the splats up I will have to see about how Imma do those depending how I decide to design them

Sent from my iPhone using Tapatalk

dnieves · 02-04-2018, 05:01 PM

Quote:

Originally Posted by Slushboxr

Haha I'm actually gonna round the edges more and put a trip around it so the ends aren't bare. Two existing from the sway bar and two into the bash bar. When I put the splats up I will have to see about how Imma do those depending how I decide to design them

Sent from my iPhone using Tapatalk

Sounds great, please post pics!!

Slushboxr · 02-04-2018, 05:31 PM

Quote:

Originally Posted by dnieves

Sounds great, please post pics!!

What it looks like so far. Gotta put to more screws in each fin and pains it black. Then do the pieces that extend out into the spats.

Sent from my iPhone using Tapatalk

Brink · 02-04-2018, 05:58 PM

Quote:

Originally Posted by Slushboxr

What it looks like so far. Gotta put to more screws in each fin and pains it black. Then do the pieces that extend out into the spats.

Sent from my iPhone using Tapatalk

So are you looking for this to be similar in appearance to the Charvonia diffuser when it's finished? I guess theirs doesn't have the flat portion extending forward though, just the angled back portion.
http://www.ft86speedfactory.com/char...2013-ft86.html

Slushboxr · 02-04-2018, 06:05 PM

Quote:

Originally Posted by Brink

So are you looking for this to be similar in appearance to the Charvonia diffuser when it's finished? I guess theirs doesn't have the flat portion extending forward though, just the angled back portion.
http://www.ft86speedfactory.com/char...2013-ft86.html

Not at all. Like I said I still have pieces to add on that we'll come down and under the muffler then out the side into the spats. That one is just pretty much what I have now but mine is only half way finished. This is just the center piece. I know that one goes under the muffler too but I'm continuing pass the bumper and either going up or down for a spat. Maybe both

Sent from my iPhone using Tapatalk

dnieves · 02-04-2018, 10:45 PM

Stupid question, isn't the rear bumper skin all one piece except for the reflector/rear lights lens? How is the black portion so cleanly separated from the rest of the bumper?

Ashikabi · 02-04-2018, 10:46 PM

Quote:

Originally Posted by dnieves

Stupid question, isn't the rear bumper skin all one piece except for the reflector/rear lights a lens? How is the black portion so cleanly separated from the rest of the bumper?

Cutting very carefully

Slushboxr · 02-04-2018, 10:48 PM

Quote:

Originally Posted by dnieves

Stupid question, isn't the rear bumper skin all one piece except for the reflector/rear lights a lens? How is the black portion so cleanly separated from the rest of the bumper?

It's actually real simple. I was gonna use a dremel but my friend did it with a razor blade. So that's what I used. Cuts clean and easy. Can do it like in 5-10 min. Just gotta take off the light and two brackets that are held by clips.

Sent from my iPhone using Tapatalk

dnieves · 02-04-2018, 10:49 PM

Quote:

Originally Posted by Ashikabi

Cutting very carefully

Wow!!! That's difficult......

StraightOuttaCanadaEh · 02-04-2018, 11:34 PM

aaaaand the seat covers are installed

Teseo · 02-04-2018, 11:46 PM

Looks luxury

Spuds · 02-04-2018, 11:56 PM

Quote:

Originally Posted by Slushboxr

Work on my diffuser

Sent from my iPhone using Tapatalk

Why did you fold the ends of both strakes to the same side? Why not both to the inside or outside?

Slushboxr · 02-04-2018, 11:59 PM

Quote:

Originally Posted by Spuds

Why did you fold the ends of both strakes to the same side? Why not both to the inside or outside?

Honest answer... No idea. Wish I would have put them both on the inside though

Sent from my iPhone using Tapatalk

02-04-2018, 11:34 PM	#18253
StraightOuttaCanadaEh Wes Join Date: Feb 2017 Drives: Artisan Spirits '17 86 Location: Toronto Posts: 2,871 Thanks: 1,255 Thanked 1,734 Times in 1,025 Posts Mentioned: 21 Post(s) Tagged: 0 Thread(s)	aaaaand the seat covers are installed __________________ Instagram: @gt86ws

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Saw My First FR-S Today	Marrk	Scion FR-S / Toyota 86 GT86 General Forum	26	05-15-2013 01:40 PM
Got My Car Today!!!!! First 86!! #81	Juanito08	Scion FR-S / Toyota 86 GT86 General Forum	7	05-22-2012 05:54 PM
If my FRS was here already, today I would...	bestwheelbase	Scion FR-S / Toyota 86 GT86 General Forum	101	05-12-2012 07:20 PM
Sat in a FRS today!!	Ladnerd	Scion FR-S / Toyota 86 GT86 General Forum	12	04-30-2012 02:48 PM
Got my VIN today...	Enemies	BRZ First-Gen (2012+) — General Topics	63	04-12-2012 11:19 PM

02-04-2018, 10:45 PM	#18249
dnieves Senior Member Join Date: Jul 2013 Drives: FR-S 10 Series Location: NY Posts: 1,062 Thanks: 615 Thanked 347 Times in 251 Posts Mentioned: 4 Post(s) Tagged: 0 Thread(s)	Stupid question, isn't the rear bumper skin all one piece except for the reflector/rear lights lens? How is the black portion so cleanly separated from the rest of the bumper?

02-04-2018, 11:46 PM	#18254
Teseo Senior Member Join Date: Jun 2014 Drives: frs Location: Gunsai Posts: 4,955 Thanks: 7,475 Thanked 2,981 Times in 1,803 Posts Mentioned: 23 Post(s) Tagged: 2 Thread(s)	Looks luxury

User Name		Remember Me?
Password