WHAT DID YOU DO TO YOUR FRS TODAY?

[fx1mark]

Originally Posted by Sapphireho

what am I missing? Looks the same as factory but 5 inches over?

The main point was to be able to point the camera up more. the second was to hide it. My paint is reflecting the camera. here I photo shopped the reflection out so you can how much the camera is actually showing. this is also viewed from an angle lower than the car would normally be viewed from.

[g33k]

Originally Posted by fx1mark

The main point was to be able to point the camera up more. the second was to hide it. My paint is reflecting the camera. here I photo shopped the reflection out so you can how much the camera is actually showing. this is also viewed from an angle lower than the car would normally be viewed from.

Any shots of how it looks on the head unit or if it even looks any different?

Sent from my XT1650 using Tapatalk

[Overdrive]

Originally Posted by g33k

Any shots of how it looks on the head unit or if it even looks any different?

Sent from my XT1650 using Tapatalk

It's on the previous page in his first post.

[g33k]

Originally Posted by Overdrive

It's on the previous page in his first post.

Ha my bad didn't realize the topic started a couple pages back, usually read the forum on my app. Looks good, I reversed into a BBQ pit last week and am going to drop off my car for repair Friday. Totally considering adding a cam now lol.

Sent from my XT1650 using Tapatalk

[MJones_RB]

Originally Posted by fx1mark

I installed a backup camera this week. Driving it Saturday I decided I didn't like the camera angled down like it was. I had the idea of insetting the camera into the trunk garnish. That would allow me to angle the camera as I wanted and I could also make the camera as invisible as possible. I did it today. I made an aluminum bracket and attached it with some strong two sided adhesive foam tape. it seems rock solid. I think it came out pretty good.

How hard was it to wire up to the head unit?

[fx1mark]

Originally Posted by MJones_RB

How hard was it to wire up to the head unit?

I used this kit.

http://www.ft86club.com/forums/showp...ostcount=14758

install was fairly easy. hardest part was the reverse trigger wire. I would recommend buying one pre-made. you need to tap into a jack in the back of the head unit. the jack is empty in that slot. some people jam a wire in. I didn't want to do that. It happened that I had a pin that would work. then connecting to the wire behind the drivers side kick panel is not an easy reach. I did manage to strip and solder the wire. the wire you are tapping into is pretty small. I used a 22 guage for the jumper and it was a little smaller than that. I tucked the wire going back to the camera under the center console and under the back seat. that simplified the install.
here is a pre-made trigger wire.

http://www.autoharnesshouse.com/19867_add.html

[kmbkk]

Didn't do this today, but recently installed a rear seat delete...

[auryn79]

Changed transmission fluid.

[Overdrive]

Originally Posted by kmbkk

Didn't do this today, but recently installed a rear seat delete...

Interesting. Does that panel still drop to give you a pass through for larger items, or is your trunk full of woofer now?

[kmbkk]

Originally Posted by Overdrive

Interesting. Does that panel still drop to give you a pass through for larger items, or is your trunk full of woofer now?

No pass through capability anymore. The amp rack and sub enclosure take up roughly half the trunk, basically the part under the rear deck.

[Eman]

Installed a Borla UEL header.

Eman

[dejahboi]

Added the D to the Edelbrock. One more D to go

Sent from my SAMSUNG-SM-G935A using Tapatalk

[Overdrive]

...does it like the D?

[MJones_RB]

Originally Posted by fx1mark

I used this kit.

http://www.ft86club.com/forums/showp...ostcount=14758

install was fairly easy. hardest part was the reverse trigger wire. I would recommend buying one pre-made. you need to tap into a jack in the back of the head unit. the jack is empty in that slot. some people jam a wire in. I didn't want to do that. It happened that I had a pin that would work. then connecting to the wire behind the drivers side kick panel is not an easy reach. I did manage to strip and solder the wire. the wire you are tapping into is pretty small. I used a 22 guage for the jumper and it was a little smaller than that. I tucked the wire going back to the camera under the center console and under the back seat. that simplified the install.
here is a pre-made trigger wire.

http://www.autoharnesshouse.com/19867_add.html

Thanks for the great links! Will def do this.