BRZ Ts parts

[kuczynskika]

Originally Posted by Trap63

About microns the total amount of clear coat over pink coat. If you exceed near sides on bottom paint might break.

Inviato dal mio SM-G935F utilizzando Tapatalk

Oh Gottcha! That makes sense then. How much does the trim flex? Once it's in position I don't see why it would move around and distort the paint.


Sent from my iPhone using Tapatalk

[Trap63]

The trim shape is plain and bumper grille is closest near 40° when curve on the two lower sides.

Inviato dal mio SM-G935F utilizzando Tapatalk

[Trap63]

done!

[kuczynskika]

Originally Posted by Trap63

done!

Very nice! Looks good. I will probably do the same in the near future and re-coat with proper chrome and cherry blossom.

[DSOmegaX]

Originally Posted by Trap63

done!

Dayummm make one for me 😩 haha



Sent from my iPhone using Tapatalk

[Trap63]

Originally Posted by DSOmegaX

Dayummm make one for me �� haha



Sent from my iPhone using Tapatalk

it's very noise to do and rebuild....chrome first of all...
I don't understand the "reason why"about FT86factory sells this one not so closest to genuine...(red and satin chrome).

[krayzie]

Originally Posted by chanomatik

No I did not. I placed the bracket first, pushed the Styrofoam piece over and lined up the bracket with the screw points. It sits right in them. Then I put the screws in, but they don't screw all the way down. Then the STI emblem clicks right in place.

Sent from my SAMSUNG-SM-G925A using Tapatalk

Humm would this work for turning the screws all the way down? (this comes with my Victorinox SwissTool from STI)



I just tried to stick my fat hand into the grill and I don't even think I would have that kind of reach sigh forget it.

[chanomatik]

Yeah I think after the initial bite you could torque them down with that. Hopefully you have small hands or know someone with small hands!

Sent from my SAMSUNG-SM-G925A using Tapatalk

[krayzie]

Originally Posted by chanomatik

Yeah I think after the initial bite you could torque them down with that. Hopefully you have small hands or know someone with small hands!

Sent from my SAMSUNG-SM-G925A using Tapatalk

Yea the most I can stick into the front bumper vents are two fingers so it won't work out, my gf might just drop the ratchet into the rad altogether unless I tie a fishing line to it lol!

[Mr.Impreza]

Originally Posted by nikitopo

It is not a tS part, but I liked that it was installed on a tS car. Fujitsubo exhaust!

Welcome to the Fujitsubo club

[muckypuppy]

Originally Posted by krayzie

Yea the most I can stick into the front bumper vents are two fingers so it won't work out, my gf might just drop the ratchet into the rad altogether unless I tie a fishing line to it lol!

I ended up removing my bumper to do mine. My AUDM bumper had a small plastic air guide screwed into the mounting points for the bracket which I had to remove in order to install the emblem. Maybe you could raise the front, remove the plastic under tray and access it from below ?

[DSOmegaX]

Originally Posted by nikitopo

It is not a tS part, but I liked that it was installed on a tS car. Fujitsubo exhaust!

Fun fact actually, fujitsubo makes the STI axleback

[krayzie]

Originally Posted by DSOmegaX

Fun fact actually, fujitsubo makes the STI axleback

Where does it say that? I remembered trying to look for a marking on the box and on the exhaust but didn't find any. Just curious.

[chaoskaze]

Originally Posted by DSOmegaX

Fun fact actually, fujitsubo makes the STI axleback

don't stop with a clift hanger, my ears is ready!