Another one bites the dust

[texasbound972]

Originally Posted by SoCal80six

Really how are they and where are they located?

Sent from my SM-G935T using Tapatalk

300 Quay Ave, Los Angeles, CA 90744

Sent from my SAMSUNG-SM-N920A using Tapatalk

[SoCal80six]

Originally Posted by texasbound972

300 Quay Ave, Los Angeles, CA 90744

Sent from my SAMSUNG-SM-N920A using Tapatalk

How's your tune hp,tq?

Sent from my SM-G935T using Tapatalk

[texasbound972]

Originally Posted by SoCal80six

How's your tune hp,tq?

Sent from my SM-G935T using Tapatalk

Not tuned to the extreme, but a safe and reliable tune.

Sent from my SAMSUNG-SM-N920A using Tapatalk

[SoCal80six]

Originally Posted by texasbound972

Not tuned to the extreme, but a safe and reliable tune.

Sent from my SAMSUNG-SM-N920A using Tapatalk

That's more than enough for this car. How's your trans holding up?

Sent from my SM-G935T using Tapatalk

[texasbound972]

Originally Posted by SoCal80six

That's more than enough for this car. How's your trans holding up?

Sent from my SM-G935T using Tapatalk

It's good. Had to replace it because my Trd shifter worked itself loose and when I was carving the canyon roads, it didn't go into 4th properly and I fucked the syncros. Other than that it holds the power just fine. Even the stock axles. My driveshaftshop ones should be here from being repaired by the end of this week or next week. As long as you don't launch with the stock axles, you'll be okay.

Sent from my SAMSUNG-SM-N920A using Tapatalk

[texasbound972]

Bought a used one with 25k miles on it for 600.

Sent from my SAMSUNG-SM-N920A using Tapatalk

[p1l0t]

Originally Posted by texasbound972

Not tuned to the extreme, but a safe and reliable tune.

Sent from my SAMSUNG-SM-N920A using Tapatalk

DAYUM

Sent from my SM-G920P using Tapatalk

[SoCal80six]

Originally Posted by texasbound972

It's good. Had to replace it because my Trd shifter worked itself loose and when I was carving the canyon roads, it didn't go into 4th properly and I fucked the syncros. Other than that it holds the power just fine. Even the stock axles. My driveshaftshop ones should be here from being repaired by the end of this week or next week. As long as you don't launch with the stock axles, you'll be okay.

Sent from my SAMSUNG-SM-N920A using Tapatalk

Will keep that in mind not to launch ahah. Are you running a aem failsafe of yours?

Sent from my SM-G935T using Tapatalk

[texasbound972]

Originally Posted by SoCal80six

Will keep that in mind not to launch ahah. Are you running a aem failsafe of yours?

Sent from my SM-G935T using Tapatalk

Yes, installed after having it over a year lol. Just procrastinated putting it in. No fancy bracket or mount needed!

Sent from my SAMSUNG-SM-N920A using Tapatalk

[SoCal80six]

Originally Posted by texasbound972

Yes, installed after having it over a year lol. Just procrastinated putting it in. No fancy bracket or mount needed!

Sent from my SAMSUNG-SM-N920A using Tapatalk

Did you wire to your ecu?

Sent from my SM-G935T using Tapatalk

[texasbound972]

Originally Posted by SoCal80six

Did you wire to your ecu?

Sent from my SM-G935T using Tapatalk

I didn't rewire my ecu.

Sent from my SAMSUNG-SM-N920A using Tapatalk

[SoCal80six]

Originally Posted by texasbound972

I didn't rewire my ecu.

Sent from my SAMSUNG-SM-N920A using Tapatalk

How did you install failsafe?

Sent from my SM-G935T using Tapatalk

[texasbound972]

Originally Posted by SoCal80six

How did you install failsafe?

Sent from my SM-G935T using Tapatalk

Had to drill through the aluminum ducting to route the wires, then just plummed it together. Used the mounting hardware that came with the failsafe to attach it to the honeycomb part of the vent.

Sent from my SAMSUNG-SM-N920A using Tapatalk

[SoCal80six]

Originally Posted by texasbound972

Had to drill through the aluminum ducting to route the wires, then just plummed it together. Used the mounting hardware that came with the failsafe to attach it to the honeycomb part of the vent.

Sent from my SAMSUNG-SM-N920A using Tapatalk

Does the failsafe mode work? I heard you had to wire it to your ecu to actually get the failsafe feature to work.

Sent from my SM-G935T using Tapatalk