|
||||||
| Forced Induction Turbo, Supercharger, Methanol, Nitrous |
 |
|
|
Thread Tools | Search this Thread |
12-24-2015, 04:03 PM
|
#1 |
|
Sarcastic SOB
Join Date: May 2012
Drives: '13 FR-S M6, '23 Volvo V60 CC
Location: Toronto Ontario
Posts: 4,644
Thanks: 1,362
Thanked 2,858 Times in 1,642 Posts
Mentioned: 32 Post(s)
Tagged: 3 Thread(s)
|
Request: JR S/C owner need pic oil cooler bracket
Hi all,
Small request, I am installing the Setrab 10 row oil cooler used in the Jackson Racing kit as a traction oil cooler for my HKS setup. I will need to fabricate a mounting bracket for it and kindly request if anyone has a pic of the bracket itself and where it mounts to the vehicle, orientation etc. Perhaps a page or two from the installation manual. Thanks in advance.
__________________
5:AD kit, HKS V1+ S/C, ECUtek dyno'd, Ohlins MP20, Magnaflow cb, Revworks UEL, Topspeed overpipe, Pinnacle Ceramic tint, VG shark fin, HID's, yellow DRL's, full LEDs, red floor lights, Homelink mirror, trunk lid liner, Perrin LWCP, Valenti smoked, Flossy Grip Tape Shorty, GT86 plaque, lighted vanity mirror, Michelin PSS, Project mU +800, DOT4 fluid, 720 Form GTF1 17x8&9, stitched leather bits, EZ valve.
|
|
|
|
12-24-2015, 05:56 PM
|
#2 |
|
Senior Member
Join Date: Jan 2013
Drives: Asphalt Scion FR-S
Location: Los Angeles, CA
Posts: 499
Thanks: 274
Thanked 215 Times in 136 Posts
Mentioned: 10 Post(s)
Tagged: 1 Thread(s)
|
Installation manual is available online from the JR website. I don't have the JR SC but own the JR engine oil cooler. It mounts below the front crash beam in holes readily available. It is possible to fab a similar mounting plate.
Sent from my HTC6525LVW using Tapatalk
__________________
|
|
|
|
|
12-24-2015, 06:03 PM
|
#3 |
|
Senior Member
Join Date: Oct 2012
Drives: 2013 Ultramarine FR-S
Location: Liberty Lake
Posts: 1,209
Thanks: 1,978
Thanked 539 Times in 327 Posts
Mentioned: 18 Post(s)
Tagged: 2 Thread(s)
|
Are looking for help in fabricating your own bracket or are you just want into rip off the JR bracket? Is buying the bracket from JR not possible?
|
|
|
|
|
12-24-2015, 06:38 PM
|
#4 |
|
Sarcastic SOB
Join Date: May 2012
Drives: '13 FR-S M6, '23 Volvo V60 CC
Location: Toronto Ontario
Posts: 4,644
Thanks: 1,362
Thanked 2,858 Times in 1,642 Posts
Mentioned: 32 Post(s)
Tagged: 3 Thread(s)
|
This is the bracket for the traction fluid cooler. No I am not looking to rip off anything, in fact I kinda got ripped of on a used HKS S/C that I discovered was missing the traction fluid cooler after the sellers mechanic did the swap. This lead to a chain of events and the eventual failure of my S/C. After waiting 6 months and spending more than $3K in my currency, I have a replacement blower. Since HKS doesn't sell their cooler a la carte I sourced a Setrab unit same as the Jackson kit uses. I need to mount it reliably.
__________________
5:AD kit, HKS V1+ S/C, ECUtek dyno'd, Ohlins MP20, Magnaflow cb, Revworks UEL, Topspeed overpipe, Pinnacle Ceramic tint, VG shark fin, HID's, yellow DRL's, full LEDs, red floor lights, Homelink mirror, trunk lid liner, Perrin LWCP, Valenti smoked, Flossy Grip Tape Shorty, GT86 plaque, lighted vanity mirror, Michelin PSS, Project mU +800, DOT4 fluid, 720 Form GTF1 17x8&9, stitched leather bits, EZ valve.
|
|
|
|
|
12-24-2015, 08:06 PM
|
#5 |
|
Sarcastic SOB
Join Date: May 2012
Drives: '13 FR-S M6, '23 Volvo V60 CC
Location: Toronto Ontario
Posts: 4,644
Thanks: 1,362
Thanked 2,858 Times in 1,642 Posts
Mentioned: 32 Post(s)
Tagged: 3 Thread(s)
|
Thanks for informing of the online manual JDKane527. Looking at the mounting, it is specific to the top of the Jackson intercooler. I guess I'll have to find a way to mount it in a similar location behind my intercooler, just above my engine oil cooler. I have all winter to figure it out.
__________________
5:AD kit, HKS V1+ S/C, ECUtek dyno'd, Ohlins MP20, Magnaflow cb, Revworks UEL, Topspeed overpipe, Pinnacle Ceramic tint, VG shark fin, HID's, yellow DRL's, full LEDs, red floor lights, Homelink mirror, trunk lid liner, Perrin LWCP, Valenti smoked, Flossy Grip Tape Shorty, GT86 plaque, lighted vanity mirror, Michelin PSS, Project mU +800, DOT4 fluid, 720 Form GTF1 17x8&9, stitched leather bits, EZ valve.
|
|
|
|
|
|
|
|
|
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| New owner of a CPO (Certified Preowned) BRZ. Question with previous owner's audio mod | tekniq | BRZ First-Gen (2012+) — General Topics | 2 | 12-05-2014 03:15 AM |
| Robispec Radiator/oil cooler NEW $800 or trade for NEW FB oil cooler kit. | mike the snake | Engine, Exhaust, Bolt-Ons | 1 | 01-31-2014 05:46 PM |
| Request: Filling in holes from dealer license plate bracket? | t00n3wb | DIY (Do-It-Yourself) Guides | 12 | 08-14-2013 08:06 AM |
| Request DIY oil cooler kit | brillo | DIY (Do-It-Yourself) Guides | 5 | 04-29-2013 10:17 AM |
| Tonight: I need a Portland BRZ owner and S2000 owner! | DarrenDriven | Northwest | 2 | 06-19-2012 02:40 AM |
2013 Scion FR-S