The BlueBaru CX Racing Turbo Rebuild

[TurboBRZ]

Originally Posted by King Tut

Innovate doesn't sell an SC2. What exactly is your wideband setup? Do you have the LC-2 hooked up to an aftermarket gauge? I believe the Innovate wideband has to be properly calibrated for it to work. Did you perform the calibration prior to install? Those numbers you keep posting don't make any sense. You should be at 14.7 at idle and cruising. You should be around 13 during partial throttle, and you should be in the 11 to 12 range during WOT.

Yeah I made a typo, it's a brand new LC-2 from innovate. I did not do any calibration I simply installed it and wired it in. Guess I should have read the entire manual - I didn't realize it wasn't a plug n play device.

[King Tut]

Originally Posted by TurboBRZ

Yeah I made a typo, it's a brand new LC-2 from innovate. I did not do any calibration I simply installed it and wired it in. Guess I should have read the entire manual - I didn't realize it wasn't a plug n play device.

Start on page 5:

http://www.innovatemotorsports.com/s...C-2_Manual.pdf

[TurboBRZ]

Originally Posted by King Tut

Start on page 5:

http://www.innovatemotorsports.com/s...C-2_Manual.pdf

Thanks for your help! I have the O2 removed and will begin calibration after lunch.

EDIT: After calibration my sensor is now reading properly. Thanks again Tut!

[King Tut]

Originally Posted by TurboBRZ

Thanks for your help! I have the O2 removed and will begin calibration after lunch.

EDIT: After calibration my sensor is now reading properly. Thanks again Tut!

No problem man. Always here to help.

[TurboBRZ]

I go in for my full tune on Monday. Right now I'm maxing out around 5psi at 3/4 throttle with AFR's around 14/15 so I haven't done a whole lot of driving like that (just enough to feel what it can do). DAMN. I can't wait for 12+psi

[philooo]

subscribed, nice build ! and I am also in fort lauderdale, so I realy enjoy reading your recommandation. I may use Platinum Paint and Body for some body work my car needs

[TurboBRZ]

Originally Posted by philooo

subscribed, nice build ! and I am also in fort lauderdale, so I realy enjoy reading your recommandation. I may use Platinum Paint and Body for some body work my car needs

You'll be very happy if you do. They're good people and do great work. Are you coming to the meet tonight at Dave n busters in Hollywood?

https://www.facebook.com/events/413447092180280/

[philooo]

argh missed that one ... I need to get my Facebook in better order

[philooo]

I was reading your earlier post where you mention that you know what to look for in salvage BRZ/FRS to avoid frame damage

Would you share your finding, and point at what to look for when buying a crashed car ?

[Top-Secret]

its now monday. updates on the tune!?!

[TurboBRZ]

Just got home from a 7hr round trip drive to Orlando. James at HRI Tuning is a pro. I now have 3 maps at 7, 9 and 12 psi on pump gas and she pulls hard! Going in for a dyno run later this week to see where it's at. All I know is I am in love with this car and my turbo is holding up just fine

[TurboBRZ]

I have a date at 5pm tonight with a local DynoJet to see what kind of numbers I'm putting to the ground. Will post the results when I'm back!

If all goes well I will also be going to the local drag strip tomorrow night to see what kind of numbers I can hit on stock tires.

[Mathewgzlz]

Stock tires are going to kill your times

Sent from my SM-G900P using Tapatalk

[TurboBRZ]

Originally Posted by Mathewgzlz

Stock tires are going to kill your times

It's simply a base line to see how much improvement some 9.5" Michelin Pilot Super Sports make. I wanna see how much time I gain from adding bigger, better tires - kinda like any other mod I do.