Delicious Tuning - Q&A EcuTeK ProECU Tuning and Maps

[Calum]

Originally Posted by FRS Justin

1.8 60ft is the best usually a 1.9 with hoozier street slicks


All engine mods are:
1: k/n panel filter
2: PPE header and over pipe
3: invidia exhaust and front pipe
4: E85 Stage 2 tune from Delicious Tuning
5: ACT Clutch and streetlite flywheel




No lightweight pulleys
no cold air intake
no crawford blocks


I will shoot you straight I have tried other headers other tuners but nothing comes close to this setup, I live in San Antonio and made over 200 wheel horsepower on a dynapac dyno on a day that was 100 degrees and 50 to 60 percent humidity.
Last night I ran multiple 13.61's and 100mph passes, its a really consistent setup. It will go faster based on i was running in a 7 to 10 mph head wind. The flags at the track were blowing straight torwards me lol
Are 12's possible N/A I dont know but nobody thought mid 13's or breaking 100 mph in the 1/4 were either at one time lol
I'm Working on something right now that might get me down a few more tenths but its going to take a little time..... lol
peace and thanks for the props!!!!

I can't tell from the vid, is that the Q300 or the N1?

[FRS Justin]

Its the N1

[R2]

Originally Posted by FRS Justin

1.8 60ft is the best usually a 1.9 with hoozier street slicks


All engine mods are:
1: k/n panel filter
2: PPE header and over pipe
3: invidia exhaust and front pipe
4: E85 Stage 2 tune from Delicious Tuning
5: ACT Clutch and streetlite flywheel




No lightweight pulleys
no cold air intake
no crawford blocks


I will shoot you straight I have tried other headers other tuners but nothing comes close to this setup, I live in San Antonio and made over 200 wheel horsepower on a dynapac dyno on a day that was 100 degrees and 50 to 60 percent humidity.
Last night I ran multiple 13.61's and 100mph passes, its a really consistent setup. It will go faster based on i was running in a 7 to 10 mph head wind. The flags at the track were blowing straight torwards me lol
Are 12's possible N/A I dont know but nobody thought mid 13's or breaking 100 mph in the 1/4 were either at one time lol
I'm Working on something right now that might get me down a few more tenths but its going to take a little time..... lol
peace and thanks for the props!!!!

Do you need to pull the ABS fuse to do a burnout without the ECM cutting power?

[FRS Justin]

Originally Posted by R2

Do you need to pull the ABS fuse to do a burnout without the ECM cutting power?

No just get down on it!!!!!!

[FRS Justin]

Originally Posted by Calum

I can't tell from the vid, is that the Q300 or the N1?

Hey Calum hold on for a minute if your looking for a n1 exhaust I beleive there might be something that works better its in r&d right now. I will keep you posted


And its LIGHT WEIGHT AND STAINLESS!!!

[M23]

Originally Posted by FRS Justin

I will shoot you straight I have tried other headers but nothing comes close to this setup

You've tried Nameless and JDL headers?

So you're saying the PPE headers are better than the JDL and Nameless header?

[FRS Justin]

Originally Posted by M23

You've tried Nameless and JDL headers?

So you're saying the PPE headers are better than the JDL and Nameless header?

The PPE header made the most power on my car, Im sure different tuners like different products beleive me you have to tune to each header specifically. I will try to dig up some data and post it.

[M23]

Originally Posted by FRS Justin

The PPE header made the most power on my car, Im sure different tuners like different products beleive me you have to tune to each header specifically. I will try to dig up some data and post it.

I thought Delicious specifically recommends (and have tuned primarily with) JDL headers first and foremost tho? ...and other good headers like Nameless and PPE are also recommended by them of course; but JDL was on the top of their list of recommendations.

So it sounds like their tune was really made with/for JDL; but will also work with other good headers like Nameless and PPE.

[FRS Justin]

Originally Posted by M23

I thought Delicious specifically recommends (and have tuned primarily with) JDL headers first and foremost tho? ...and other good headers like Nameless and PPE are also recommended by them of course; but JDL was on the top of their list of recommendations.

So it sounds like their tune was really made with/for JDL; but will also work with other good headers like Nameless and PPE.

I know this tune works well with PPE for sure as far as with other headers that I cant say which leads me to this disclaimer lol


Ive been working with Will for a while and hes been there every step of the way to get the records but before Will I was with a different tuner and didnt get the results I was looking for and thats where I tested the other headers.


I dont want to come on here and bash other tuners for not getting the results I wanted nor will I bash on other peoples products I will simply just share the results I get so others have the info to make up their mind which path they want to follow. I dont need Bad Karma. lol


All I know is 3 things
1 Delicious Tuning is my tuner
2 PPE is my perferred Header
3 When in doubt FLOOR IT!!!!

[M23]

Das cool. PPE will defo be on my header list then

[FRS Justin]

Originally Posted by M23

Das cool. PPE will defo be on my header list then

Oh snap you going after the record lol
I'll sleep with one eye open so I can be watchin you....


Just look at it this way you can have a custom tune and a proven header for the cost of different header.... If you already have a ecutek.


SO since you are coming after me you need to call Paul at PPE and put your name on the list to get a custom exhaust all the way out he has 2 versions a single and a dual in R&D
did I just say that?? oh well now you know

[texasbound972]

Bought bills jdl kit and it's getting installed Monday. Can't wait! Gonna test a new something he's come up with! Won't spill the beans.

[FRS Justin]

Originally Posted by texasbound972

Bought bills jdl kit and it's getting installed Monday. Can't wait! Gonna test a new something he's come up with! Won't spill the beans.

Ahh I think I know what that is......


Your going to love the tune

[DeliciousTuning]

For you Flash and Go customers (most all forced induction customers) we have moved the Flash & Go Q&A to a new thread to be able to maintain a more coherent line of communication about updates, questions and requests.

New Location: Click Here

Cheers,
William Knose
Delicious Tuning