Exhaust tips

[subiestyle]

Originally Posted by White64Goat

Here are the DC tips. They looked very nice and I used them until I got my cat-back.



Picked them up at Advanced Auto but I'm not sure if they're still selling them.
[/B][/COLOR]

How's the rust?

[kodyo]

I did a quick DIY a while back to make my own tips using a set of weld on magnaflows that I turned into clamp-ons. Was about $90 all said and done.
http://www.ft86club.com/forums/showt...hlight=exhaust

[FrsDuke]

Originally Posted by kodyo

I did a quick DIY a while back to make my own tips using a set of weld on magnaflows that I turned into clamp-ons. Was about $90 all said and done.
http://www.ft86club.com/forums/showt...hlight=exhaust

Link doesn't lead to the DIY.

[kodyo]

Originally Posted by FrsDuke

Link doesn't lead to the DIY.

Scroll down. It was an addition to an old DIY. The original OP deleted it for some reason, but my write up is a few posts down.

I just added an edit so that you get the basic content of the original post.

[White64Goat]

No problem with rust during the period of time I had them on. They're stainless.

[DAEMANO]

Originally Posted by ramiram1984

get one of these.

Duck call exhaust are the new whistle tips! WOOOWOOOO!! QUACK!

[DAEMANO]

Originally Posted by kodyo

Scroll down. It was an addition to an old DIY. The original OP deleted it for some reason, but my write up is a few posts down.

I just added an edit so that you get the basic content of the original post.

Here's the link without the context
http://www.ft86club.com/forums/showp...1&postcount=11

[FrsDuke]

Gotcha lol didn't see the update at the bottom of your post. Looks sharp

[SloS14]

Originally Posted by DAEMANO

Duck call exhaust are the new whistle tips! WOOOWOOOO!! QUACK!

That's only in da mornin'. You 'posed to be up cookin brefas fo somebody and so that's like an alarm clock. Woo WOO

[FrsDuke]

http://tailgunnerexhaust.com
Lol

/thread

[DAEMANO]

Originally Posted by FrsDuke

http://tailgunnerexhaust.com
Lol

/thread

What is this fuckery?!

[subiestyle]

Originally Posted by White64Goat

No problem with rust during the period of time I had them on. They're stainless.

are the screws stainless too?

also, what is the taper like from the outside edge to the inside tube wall? Is it a straight line or curve.

[cycleboy]

Originally Posted by humfrz

hmmmm.......you must like them tucked way back. When I had them on my stock muffler, they could have gone back another 1/2" ...


humfrz

They stick out about an inch to inch and a half. I'd like them a bit closer to even w/ the rear fascia. 1/2 to 1 inch in from where they are would be great.

My favorite tips, being a cyclist, is the bike inner tube:

[ame]http://youtu.be/ieJUP9O9RG8[/ame]

[suaveflooder]

Originally Posted by cycleboy

I got the Perrin and they look a lot better than stock. I just wish I could shove them on a little further as they stick out a bit much for my liking.

I got them because I'd like to go to Borla catback + diffuser, but that's the difference between under $200 for tips or $1000 for what I really want. I'll keep these until I can do the full thing, then sell the tips. Likely they will look just about new at that point too. They are well made.

It's a pain, but you can get them to go further in. Mine sat out too far at first as well. Use both hands and twist. They all still sit out further than the perrin catback, but they won't poke out like they probably are now.