oCarbon custom CF trim for my BRZ - build thread

[Ongor]

hey KSpider, im def interested in this. What about the 2 silver trims around the AC center area?

And how much would it be for a full kit? (all the pieces shown+the 2 i mentioned)

Awesome stuff! im jealous :P

[KSpider]

Originally Posted by Ongor

hey KSpider, im def interested in this. What about the 2 silver trims around the AC center area?

And how much would it be for a full kit? (all the pieces shown+the 2 i mentioned)

Awesome stuff! im jealous :P

Those two pieces by the knees are done, I just didn't have them yet when those pics were taken.

Direct pricing questions to Matt@oCarbon.com

Everyone compliments the CF interior, it looks damn good.

Here you go!

[SirBrass]

Can't say I'm a fan. I think that checkerboard CF look is entirely too much.

However, that is a very clean job and well done.

[Sniper2606]

Originally Posted by KSpider

Getting very close, should start getting finished product this week. Here are some shots.

Hate to be THAT guy but....

Anybody can achieve the same results with the Dipkit using OEM parts, looks exactly the same as your pics...

Water = Free (sort of speak)

Activator $18: http://www.ebay.com/itm/111243548662...84.m1439.l2649

80 inches of carbon fiber sheet was only $8: http://www.ebay.com/itm/111252328384...84.m1439.l2649



For example


IMAG0533 by sniper260687, on Flickr

[ucsmfu]

Originally Posted by Sniper2606

Hate to be THAT guy but....

Anybody can achieve the same results with the Dipkit using OEM parts, looks exactly the same as your pics...

Water = Free (sort of speak)

Activator $18: http://www.ebay.com/itm/111243548662...84.m1439.l2649

80 inches of carbon fiber sheet was only $8: http://www.ebay.com/itm/111252328384...84.m1439.l2649



For example


IMAG0533 by sniper260687, on Flickr

is it naturally glossy after hydrodipping it or do you need to apply a clear coat ?

thanks

[Sniper2606]

Originally Posted by ucsmfu

is it naturally glossy after hydrodipping it or do you need to apply a clear coat ?

thanks

It depends, if you sand your piece down then no.

But per instructions clear coat is a must after

I just sprayed primer,dip,rinse,clear coat.

Oh and that piece has just came out no clear coat yet

[KSpider]

Dip kit is not exactly the same as oem like real cf...

[Kristian]

Originally Posted by KSpider

Dip kit is not exactly the same as oem like real cf...

Do you mind sharing what this interior setup cost? Cheers.

[KSpider]

Originally Posted by Kristian

Do you mind sharing what this interior setup cost? Cheers.

I do not know, to be honest. My costs are unrelated as this was the test run, molds were created and it is my buddies shop.

You will have to email matt@ocarbon.com to find out pricing info.

[KSpider]

Originally Posted by Kristian

Do you mind sharing what this interior setup cost? Cheers.

oCarbon is going to do these kits for $800. That's a steal.

[Pat]

As some others here have said, oCarbon's quality is top shelf. Ive seen their work on a bunch of Audis.

[boredom.is.me]

$800........................not in my wildest dreams, but that's just me.

[Minovsky]

Originally Posted by KSpider

oCarbon is going to do these kits for $800. That's a steal.

would he be able to do seperate parts ie door handles and the radio/passenger dash?

[KSpider]

Originally Posted by Honeydew

would he be able to do seperate parts ie door handles and the radio/passenger dash?

Email him and ask, i would assume so. I have the door handle cores I can provide. i sold the dash pieces though,