BRZ/FRS AZ6 Manual Trans Upgraded Gearset - Page 12 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

Drakiv · 02-04-2017, 11:16 AM

Quote:

Originally Posted by twag4

Does anyone know where I can get a ring(synchro) and bearing kit for our manual transmission? Is stock the only option?

I believe stock is the only option, I can't find anyone that makes a synchro upgrade kit or anything. I was hoping that Jacks transmission was going to offer one at some point but im not sure.

COO86L · 06-18-2017, 03:10 AM

Hey peeps, how are these gearsets going? Any issues after extended use etc?

I'm looking at doing a big build on mine and will probably blow a box. If anyone has a set they didn't end up needing I may take them off your hands ;D

Drakiv · 06-19-2017, 01:56 AM

I haven't heard of anyone having any issues yet. Still runs like the day I had them installed. I will update once I get my car back from fullblown.

SpectreRT · 09-20-2017, 12:28 AM

Quote:

Originally Posted by Drakiv

I haven't heard of anyone having any issues yet. Still runs like the day I had them installed. I will update once I get my car back from fullblown.

Any update on this?

Drakiv · 09-20-2017, 09:14 PM

Quote:

Originally Posted by SpectreRT

Any update on this?

Still running strong with no issues yet. Haven't heard of any issues from anyone else running this set yet either.

[ame="https://www.youtube.com/watch?v=HhxM2fRmi9o"]600+ whp BRZ with built motor - YouTube[/ame]

SpectreRT · 09-21-2017, 12:31 PM

Quote:

Originally Posted by Drakiv

Still running strong with no issues yet. Haven't heard of any issues from anyone else running this set yet either.

Omfg that sounds amazing. Shut up and take my money...

Surok · 12-06-2017, 01:28 AM

i have no issues with mine.

JacksTrans · 12-15-2017, 05:03 PM

hey guys,
Not sure if you've seen our other thread but we are currently working with PPG on a helical set. They will be ready sometime after their Christmas break.
we will have a new thread as soon as we get some pictures

rx3 · 10-10-2018, 06:58 AM

Is there a list of additional parts needed to rebuild a transmission using the PAR engineering gear-set?

Drakiv · 10-10-2018, 08:47 PM

Quote:

Originally Posted by rx3

Is there a list of additional parts needed to rebuild a transmission using the PAR engineering gear-set?

I don't know if there is a list out there, you could always ask Verus what parts they replace when they open them up for their gear set. Unless your trans was trashed from the get go I don't think there is too much, however I would recommend ordering a set of carbon synchros from Verus Engineering if they still have them to replace at the same time. They weren't available when I did mine, and I wish I had. I don't have synchro issues and they are still my original ones from before the gear set. Just wish I had them for the peace of mind. Just keep up on your trans oil changes and the gear set should last you a long time if you decide to do it.

rx3 · 10-11-2018, 07:21 AM

Thank you for your advice.
Btw, I did call Verus hoping that they still work on the billet transmission but unfortunately they put that project on hold.

olsonpg · 10-12-2018, 05:02 PM

Quote:

Originally Posted by rx3

Thank you for your advice.
Btw, I did call Verus hoping that they still work on the billet transmission but unfortunately they put that project on hold.

Same here. Just contacted them a week ago on wanting that gearset. Kind of a shame they stopped producing it. It really captures a nice niche for people not wanting to spend a fortune on a whole gearset.

Decided on going with PAR 1st through 5th now as a substitute. Its very cost competitive with Verus's 3rd-4th imo. 3000.00 for VERUS and around 4250.00 (not including shipping).

rx3 · 10-13-2018, 07:18 AM

So did I.
I'm just a little concerned about the whining part - not because I'd personally care - but it is still a road legal car and needs to pass inspection.

This would be an alternative, but the gearing ratio spread is too wide, it's heavier, requires a new clutch and some welding: http://www.ft86club.com/forums/showthread.php?p=3000925

Lonewolf · 04-25-2020, 02:00 PM

I just wanted to bump this thread for new members and those with newer updates/feedback

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
FRS/BRZ Manual Trans Fluid	shellslinger	Mechanical Maintenance (Oil, Fluids, Break-In, Servicing)	131	11-02-2017 11:44 AM
WTB: FA20 and Six Speed Manual Trans	Cross	Want-To-Buy Requests	2	04-24-2016 01:06 AM
Manual Trans 12k miles $750 OBO	Amir Ghadiri	Transmission and Driveline	4	05-23-2015 03:35 PM
Bump start in a manual trans?	bayank	BRZ First-Gen (2012+) — General Topics	11	02-16-2014 07:47 PM
FS: 1st 86 DGM/Asphalt Scion FR-S (Manual Trans)	Neurytic	Cars for Sale/Trade	3	05-23-2013 12:54 AM

06-18-2017, 03:10 AM	#156
COO86L Senior Member Join Date: Dec 2015 Drives: 2015 86 GTS + Mitsi Lancer GSR Location: Lismore AUS Posts: 215 Thanks: 127 Thanked 93 Times in 68 Posts Mentioned: 3 Post(s) Tagged: 0 Thread(s)	Hey peeps, how are these gearsets going? Any issues after extended use etc? I'm looking at doing a big build on mine and will probably blow a box. If anyone has a set they didn't end up needing I may take them off your hands ;D

12-06-2017, 01:28 AM	#161
Surok Wise old man Join Date: Jun 2012 Drives: 86 GTS Location: Sydney Posts: 1,003 Thanks: 999 Thanked 240 Times in 161 Posts Mentioned: 7 Post(s) Tagged: 0 Thread(s)	i have no issues with mine.

12-15-2017, 05:03 PM	#162
JacksTrans Join Date: May 2016 Drives: Scion FRS - "FRSKY" Location: Colorado Posts: 27 Thanks: 4 Thanked 56 Times in 20 Posts Mentioned: 5 Post(s) Tagged: 0 Thread(s)	hey guys, Not sure if you've seen our other thread but we are currently working with PPG on a helical set. They will be ready sometime after their Christmas break. we will have a new thread as soon as we get some pictures

10-10-2018, 06:58 AM	#163
rx3 Senior Member Join Date: Mar 2013 Drives: BRZ Location: Europe Posts: 350 Thanks: 53 Thanked 114 Times in 71 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	Is there a list of additional parts needed to rebuild a transmission using the PAR engineering gear-set?

10-11-2018, 07:21 AM	#165
rx3 Senior Member Join Date: Mar 2013 Drives: BRZ Location: Europe Posts: 350 Thanks: 53 Thanked 114 Times in 71 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	Thank you for your advice. Btw, I did call Verus hoping that they still work on the billet transmission but unfortunately they put that project on hold.

10-13-2018, 07:18 AM	#167
rx3 Senior Member Join Date: Mar 2013 Drives: BRZ Location: Europe Posts: 350 Thanks: 53 Thanked 114 Times in 71 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	So did I. I'm just a little concerned about the whining part - not because I'd personally care - but it is still a road legal car and needs to pass inspection. This would be an alternative, but the gearing ratio spread is too wide, it's heavier, requires a new clutch and some welding: http://www.ft86club.com/forums/showthread.php?p=3000925

04-25-2020, 02:00 PM	#168
Lonewolf Senior Member Join Date: Dec 2011 Drives: Moped Location: CA Posts: 4,300 Thanks: 4,905 Thanked 2,132 Times in 1,195 Posts Mentioned: 21 Post(s) Tagged: 0 Thread(s)	I just wanted to bump this thread for new members and those with newer updates/feedback

User Name		Remember Me?
Password