Floor Mat Idea - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

tbwoodlee · 01-21-2013, 01:03 PM

So my floor mats are the last part of my car that mark its as an FR-S. Just now I popped the FR-S logo off of them and I have ice cubes on them to make the fabric stand back up.

I had an idea though. The 86 floor mats have the 86 logo on them like this.

They cost more money than I want to spend though considering my mats are still in good shape. I could get some sways bars instead!

86_ZN6 sells some 86 keychains here:
http://www.86-zn6.com/86-Keyring-Keychain-RED_p_11.html

I just ordered two of them and I am going to attempt to recreate the 86 floor mats by trimming the logo into a circle and attaching them to my mats. Any ideas how to keep the 86 logos in place?

chenshuo · 01-21-2013, 02:43 PM

Quote:

Originally Posted by tbwoodlee

So my floor mats are the last part of my car that mark its as an FR-S. Just now I popped the FR-S logo off of them and I have ice cubes on them to make the fabric stand back up.

I had an idea though. The 86 floor mats have the 86 logo on them like this.

They cost more money than I want to spend though considering my mats are still in good shape. I could get some sways bars instead!

86_ZN6 sells some 86 keychains here:
http://www.86-zn6.com/86-Keyring-Keychain-RED_p_11.html

I just ordered two of them and I am going to attempt to recreate the 86 floor mats by trimming the logo into a circle and attaching them to my mats. Any ideas how to keep the 86 logos in place?

Super glue

J-Money · 01-21-2013, 02:53 PM

If you weld a little bar down like the old ones have and get a washer and a lug you can screw it on from the bottom but that might take more time super glue should work or gorilla glue.

Turbowned · 01-22-2013, 07:38 PM

Great idea!

tbwoodlee · 01-22-2013, 08:41 PM

Thanks, I will post my results when I finish.

tbwoodlee · 02-09-2013, 05:21 PM

Well, I finally got around to doing this. It turned out about like I expected, it tends to match the red stitching well. Overall, it is a little smaller than I would have liked. If you noticed in the original pic, the 86 logo is about the same size as the black circle that keeps the mat in place. My alternative is a little smaller than that, but hey, it is meant to be a keychain so I can't really complain.

I opted to cover the bottom with velcro as it sticks incredibly well to the floor mats and nothing is permanent.

ph0en1xtk · 02-09-2013, 07:33 PM

when you take off the fr-s logo, if you didnt replace it with something else, how obvious would it be that it used to be there? im considering popping mine off and just leaving it as is, but i dont want it to look bad

tbwoodlee · 02-09-2013, 08:40 PM

The floor mat will be pressed down a slightly but if you put ice cubes on it and let them melt it will cause the carpet fibers to loosen up and you can brush them with an old tooth brush. After that it isn't noticeable at all.

AustinG · 02-23-2015, 10:12 PM

Quote:

Originally Posted by tbwoodlee

Well, I finally got around to doing this. It turned out about like I expected, it tends to match the red stitching well. Overall, it is a little smaller than I would have liked. If you noticed in the original pic, the 86 logo is about the same size as the black circle that keeps the mat in place. My alternative is a little smaller than that, but hey, it is meant to be a keychain so I can't really complain.

I opted to cover the bottom with velcro as it sticks incredibly well to the floor mats and nothing is permanent.

So I had the same idea, but, not finding any all-silver keychains, I opted instead of modifying the 86 fender emblems. I bought some cheap knock-off ones off of Amazon, and, using a dremel, removed the paint and cut off the pistons. I'm just using the 3M tape on the back for now, but may try out the Velcro idea.

They are about the right diameter, just a little tall.

Name: ImageUploadedByTapatalk1424743861.667181.jpg
Views: 1085
Size: 306.4 KB

Name: ImageUploadedByTapatalk1424743861.667181.jpg
Views: 1085
Size: 306.4 KB

Name: ImageUploadedByTapatalk1424743870.937987.jpg
Views: 1145
Size: 294.9 KB

Name: ImageUploadedByTapatalk1424743879.310303.jpg
Views: 2051
Size: 293.7 KB

*please ignore the dirty floor mats*

8R6 · 02-24-2015, 01:14 AM

i just put in STI mats instead lol

FR-S2GT86 · 12-12-2020, 11:15 AM

Digging this 5-year old thread up from the graveyard, I’ve been looking for something to replace the old FR-S badges on my floor mats and decided these black matte piston fender badges would look pretty good. What do you think?

FR-S2GT86 · 12-12-2020, 11:16 AM

Temporarily installed using “Hook and Loop Fastener” (just the hook part).

FR-S2GT86 · 12-14-2020, 12:43 AM

Permanently installed using aluminum threaded posts, and easily removable in just one minute.

Ernest72 · 12-15-2020, 09:16 PM

I did it on my BRZ with some cheap eBay STI badges. Screws through the matt into the badge. So far it’s held up.

02-24-2015, 01:14 AM	#10
8R6 Senior Member Join Date: Jan 2014 Drives: FRS Location: SoCal Posts: 2,086 Thanks: 2,738 Thanked 1,338 Times in 746 Posts Mentioned: 30 Post(s) Tagged: 2 Thread(s)	i just put in STI mats instead lol __________________ Team BRG inspire-usa My car build #8R6

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Floor mats.	IloveBaldEagles	Mid-Atlantic	6	12-04-2012 07:52 PM
I need to get rubber floor mat!!!	BareZ	Cosmetic Modification (Interior/Exterior/Lighting)	10	11-09-2012 03:27 AM
No floor mats?	whateatsrabbits	Scion FR-S / Toyota 86 GT86 General Forum	34	08-22-2012 06:35 PM
Did you guys get floor mats?	Longhorn248	BRZ First-Gen (2012+) — General Topics	19	07-18-2012 10:49 AM
86 floor mat	GTiko	AUSTRALIA	9	06-25-2012 10:44 PM

01-21-2013, 02:53 PM	#3
J-Money Senior Member Join Date: Dec 2012 Drives: GT-86 Location: FatFour Posts: 218 Thanks: 26 Thanked 20 Times in 17 Posts Mentioned: 2 Post(s) Tagged: 0 Thread(s)	If you weld a little bar down like the old ones have and get a washer and a lug you can screw it on from the bottom but that might take more time super glue should work or gorilla glue.

02-09-2013, 07:33 PM	#7
ph0en1xtk Senior Member Join Date: Jun 2012 Drives: Raven MT Scion FR-S Location: Houston Posts: 140 Thanks: 1 Thanked 32 Times in 23 Posts Mentioned: 7 Post(s) Tagged: 0 Thread(s)	when you take off the fr-s logo, if you didnt replace it with something else, how obvious would it be that it used to be there? im considering popping mine off and just leaving it as is, but i dont want it to look bad

12-15-2020, 09:16 PM	#14
Ernest72 Senior Member Join Date: Jul 2016 Drives: 16 Silver BRZ, 04 Silver WRX wagon Location: Rockland county, NY Posts: 1,429 Thanks: 186 Thanked 776 Times in 446 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	I did it on my BRZ with some cheap eBay STI badges. Screws through the matt into the badge. So far it’s held up.

User Name		Remember Me?
Password