|
||||||
| Engine, Exhaust, Transmission Discuss the FR-S | 86 | BRZ engine, exhaust and drivetrain. |
 |
|
|
Thread Tools | Search this Thread |
11-22-2014, 03:12 PM
|
#1 |
|
Member
Join Date: Oct 2014
Drives: 2013 Toyota 86 MT
Location: Huzhou/China
Posts: 70
Thanks: 21
Thanked 4 Times in 4 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
3" Front and over pipes for Turbo kit
Hi everyone
I am planning to install Greddy turbo kit soon, i allready have 3" catback, just trying to decide about overpipe and front pipe at the moment. Want to get them 3" too to match with catback but not sure about Greddy kit headers size. Olso can not find 3" catted front pipe other than Nameless (one piece including overpipe), is it the only option? Would prefer catted and resonated if possible, for most quiet set up. Suggestions would be appriciated. Thanks in advance. Last edited by ofuts; 11-23-2014 at 01:04 AM. |
|
|
|
11-23-2014, 03:32 PM
|
#2 |
|
Senior Member
Join Date: May 2012
Drives: 2013 Series 10 6MT FR-S
Location: Moreno Valley, CA
Posts: 5,565
Thanks: 2,013
Thanked 2,043 Times in 1,474 Posts
Mentioned: 72 Post(s)
Tagged: 0 Thread(s)
|
Greddy would not be 3 inch.
__________________
2013 Series 10 FRS #553
RCE T2's, SPC LCAs -4/2.6 camber JDL 4-2-1 EL, FP and OP, Tuned by Zach@CSG on e85 RR Wilwood Front/Rear Sport BBK, Motul 600 Fluid ARC-8 17x9 SX2 GTs 245s/Koing 17x8 v730's 225's |
|
|
|
|
11-24-2014, 07:05 AM
|
#3 | |
|
Member
Join Date: Oct 2014
Drives: 2013 Toyota 86 MT
Location: Huzhou/China
Posts: 70
Thanks: 21
Thanked 4 Times in 4 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
I dont want to mess with their downpipe since it has sensor in and outs and a part of the kit. So do i need a custom overpipe that widens from 60mm to 3", or bolting 3" will be no problem? I see that Nameless offers 2,5" and 3" gaskets, 2,5" would be better i guess. |
|
|
|
|
|
11-24-2014, 10:23 AM
|
#4 | |
|
Senior Member
Join Date: May 2012
Drives: 2013 Series 10 6MT FR-S
Location: Moreno Valley, CA
Posts: 5,565
Thanks: 2,013
Thanked 2,043 Times in 1,474 Posts
Mentioned: 72 Post(s)
Tagged: 0 Thread(s)
|
Quote:
__________________
2013 Series 10 FRS #553
RCE T2's, SPC LCAs -4/2.6 camber JDL 4-2-1 EL, FP and OP, Tuned by Zach@CSG on e85 RR Wilwood Front/Rear Sport BBK, Motul 600 Fluid ARC-8 17x9 SX2 GTs 245s/Koing 17x8 v730's 225's |
|
|
|
|
|
11-26-2014, 03:17 PM
|
#5 |
|
in orbe terrum non visi
Join Date: Jan 2014
Drives: violent
Location: Mountains
Posts: 1,747
Thanks: 279
Thanked 762 Times in 446 Posts
Mentioned: 62 Post(s)
Tagged: 1 Thread(s)
|
No reason for a 3 inch anything with the greddy kit. It doesn't make enough power to need it. If you want quiet you also don't want 3 inch.
__________________
I have E85 where there isn't E85, that's my secret.
 http://www.ft86club.com/forums/showt...t=reaper+build |
|
|
|
|
|
|
|
|
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| overpipe size | yanyan | Engine, Exhaust, Transmission | 5 | 02-01-2014 11:58 PM |
| Gasket size? | ProTekk | Scion FR-S / Toyota 86 GT86 General Forum | 1 | 07-28-2013 12:57 PM |
| Greddy sp Double Gasket mistake | topnotch | Engine, Exhaust, Transmission | 9 | 02-19-2013 01:38 AM |
| BRZ Donut Gasket same part as WRX STi Gasket? | Zadkiel | Engine, Exhaust, Transmission | 0 | 10-06-2012 08:22 AM |
