|
||||||
| Suspension | Chassis | Brakes -- Sponsored by 949 Racing Relating to suspension, chassis, and brakes. Sponsored by 949 Racing. |
 |
|
|
Thread Tools | Search this Thread |
12-23-2015, 02:31 PM
|
#1 |
|
Junior Member
Join Date: Jan 2015
Drives: 2015 FR-S Hot Lava Man-Trans
Location: San Diego, CA
Posts: 4
Thanks: 0
Thanked 2 Times in 2 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Do Buddy Club LCA drop car height?
I'm running a set of Buddy Club LCA on my car because I needed the camber adjustment in the rear to fit my tires. I am also running a set of TRD springs on stock shocks until I can afford a set of coilsovers. I noticed that my rear is lower than the front after adding the LCAs. Anyone else running Buddy Club LCA on springs? Here are the bolts I have setup. Maybe I need to switch holes on some of the LCAs. Thanks in advance.
__________________
 |
|
|
|
12-23-2015, 05:12 PM
|
#2 |
|
Not a troll
Join Date: Apr 2015
Drives: FR-S
Location: Canada
Posts: 5,104
Thanks: 8,237
Thanked 5,399 Times in 2,694 Posts
Mentioned: 266 Post(s)
Tagged: 4 Thread(s)
|
Judging by the fact there's 2 mounting holes then, I'd say yes.
|
|
|
|
| The Following User Says Thank You to Cole For This Useful Post: | go_a_way1 (12-23-2015) |
|
12-23-2015, 05:17 PM
|
#3 | |
|
Not Bаnned Anymore
Join Date: Jan 2015
Drives: Heavily Modified FRS
Location: Calgary, AB
Posts: 9,827
Thanks: 14,918
Thanked 8,275 Times in 4,797 Posts
Mentioned: 355 Post(s)
Tagged: 374 Thread(s)
|
OEM ones don't have the bend like that, aftermarket ones that do are used to lower the rear, such as yours.
__________________
Quote:
 |
|
|
|
|
|
12-26-2015, 02:38 AM
|
#4 |
|
Senior Member
Join Date: Apr 2013
Drives: 86
Location: SA
Posts: 364
Thanks: 395
Thanked 116 Times in 81 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
|
Can you show us a picture of the car from outside.
I want to see how much drop it added to the rear. Thanks Sent from my 86 using Tapatalk
__________________
VOLK LE37 17X7.5, SWIFT Springs, Bilstein B8, HKS intake duct, Cosworth Air Filter, HKS headers, PLM Over Pipe, EVS Down Pipe & Exhaust, FD 4.55, GFB pulleys, Axle-Exchange Drive Shaft, Mishimoto oil cooler, Cusco F&R strut bar, TRD door stabilizer, Innovate SC, Delicious Tuned
|
|
|
|
|
12-28-2015, 06:05 PM
|
#5 | |
|
Junior Member
Join Date: Jan 2015
Drives: 2015 FR-S Hot Lava Man-Trans
Location: San Diego, CA
Posts: 4
Thanks: 0
Thanked 2 Times in 2 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Rear is about a half inch lower than front. 
__________________
Last edited by cabusi; 12-28-2015 at 06:17 PM. |
|
|
|
|
| The Following User Says Thank You to cabusi For This Useful Post: | 8686 (01-01-2016) |
|
|
|
|
|
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Buddy Club Racing Spec Damper, Buddy Club Ball Joints, Megan Extended Tie Rods, etc | Chase Bays | Brakes, Suspension, Chassis | 14 | 02-03-2016 09:14 PM |
| PBM pro coilovers drop height | keonigt | Suspension | Chassis | Brakes -- Sponsored by 949 Racing | 2 | 07-13-2015 09:27 PM |
| CA: FS Buddy Club LCA | merino_frs | Brakes, Suspension, Chassis | 1 | 06-16-2015 10:30 PM |
| The Buddy Club!!! | JamesBond000 | Engine, Exhaust, Transmission | 23 | 08-01-2014 09:29 PM |
| Can i drop my car an inch or more and then raise it back to stock height? | ScionFR-S | Suspension | Chassis | Brakes -- Sponsored by 949 Racing | 6 | 11-01-2012 09:02 PM |
