Clunking sound after coilover install - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

Dee · 02-27-2018, 12:55 PM

Just installed coilovers. Getting a clunk in the right rear over bumps. Really loud sound. Its only the rear right. I’ve heard check the endlinks. They feel super snug. I did the top hat torque to spec. Note I did install lower control arms with the coilover install.

Any ideas? Could it be bushings?

8RZ · 02-27-2018, 01:20 PM

Were they new or used?

Only advice I can give right now is to go back under and tighten all the nuts and bolts again.

Tcoat · 02-27-2018, 01:29 PM

When you checked did you have the weight on the car? If so jack up the corner and check again.

Dee · 02-27-2018, 02:14 PM

Quote:

Originally Posted by Tcoat

When you checked did you have the weight on the car? If so jack up the corner and check again.

Right, jacked it up. Just felt with hands no wrench, but everything seems to be snug. I felt all the bolts in this picture

8RZ · 02-27-2018, 02:17 PM

What about up top inside the trunk?

jasonojordan · 02-27-2018, 02:42 PM

When I had a noise like that it was due to the nut ontop attaching the damper to the tophat was loose.

Dee · 02-27-2018, 03:38 PM

Quote:

Originally Posted by jasonojordan

When I had a noise like that it was due to the nut ontop attaching the damper to the tophat was loose.

So an update: I am pretty sure it is coming from the top plate. However I did torque it down to manufacturers spec 15 ft/lb. I may give the manufacturer a call and see if they recommend going any higher than that.

However the left side has no issues and it is at the same torque rating

jasonojordan · 02-27-2018, 03:50 PM

Quote:

Originally Posted by Dee

So an update: I am pretty sure it is coming from the top plate. However I did torque it down to manufacturers spec 15 ft/lb. I may give the manufacturer a call and see if they recommend going any higher than that.

However the left side has no issues and it is at the same torque rating

Does your plates have the pillow bearing in it or no?

Dee · 02-27-2018, 04:32 PM

Quote:

Originally Posted by jasonojordan

Does your plates have the pillow bearing in it or no?

It is the stock plates

jasonojordan · 02-27-2018, 04:34 PM

Quote:

Originally Posted by Dee

It is the stock plates

How many miles? Did you inspect the bearing at all before switching them onto the new setup?

Dee · 02-27-2018, 04:41 PM

Quote:

Originally Posted by jasonojordan

How many miles? Did you inspect the bearing at all before switching them onto the new setup?

I did not. 60k miles. The left rear is doing it now too...

jasonojordan · 02-27-2018, 04:51 PM

60k is not alot of miles but I would deff check out the bearings in them if you are willing to remove each one that is making the noise.

What coil-overs did you go with out of curiosity.

Dee · 02-27-2018, 04:55 PM

Quote:

Originally Posted by jasonojordan

60k is not alot of miles but I would deff check out the bearings in them if you are willing to remove each one that is making the noise.

What coil-overs did you go with out of curiosity.

ST coilovers. I am awaiting response for torque rating

Dee · 02-27-2018, 04:58 PM

Quote:

Originally Posted by jasonojordan

60k is not alot of miles but I would deff check out the bearings in them if you are willing to remove each one that is making the noise.

What coil-overs did you go with out of curiosity.

Can anyone tell me what torque rating I should be doing for the piston rod to plate?

02-27-2018, 12:55 PM	#1
Dee Member Join Date: Dec 2016 Drives: 2014 Asphalt FRS Location: Tennessee Posts: 53 Thanks: 8 Thanked 7 Times in 7 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	Clunking sound after coilover install Just installed coilovers. Getting a clunk in the right rear over bumps. Really loud sound. Its only the rear right. I’ve heard check the endlinks. They feel super snug. I did the top hat torque to spec. Note I did install lower control arms with the coilover install. Any ideas? Could it be bushings?

02-27-2018, 01:29 PM	#3
Tcoat Senior Member Join Date: Jul 2014 Drives: 2020 Hakone Location: London, Ont Posts: 69,841 Thanks: 61,656 Thanked 108,294 Times in 46,456 Posts Mentioned: 2499 Post(s) Tagged: 50 Thread(s)	When you checked did you have the weight on the car? If so jack up the corner and check again. __________________ Racecar spelled backwards is Racecar, because Racecar.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
unknown knocking/clunking sound, whatever you call it....	FR-Sky	Suspension \| Chassis \| Brakes -- Sponsored by 949 Racing	16	10-25-2017 10:19 PM
Clunking Noise after Coilover install?	Bowen	Suspension \| Chassis \| Brakes -- Sponsored by 949 Racing	18	07-15-2016 11:47 AM
Clunking sound coming from suspension	Maverickgear	Issues \| Warranty \| Recalls / TSB	9	07-11-2014 03:41 PM
Weird Sound After Coilover Install (when moving steering wheel left and right)	taimysho0	Suspension \| Chassis \| Brakes -- Sponsored by 949 Racing	38	07-20-2013 02:18 AM
Neutral to 1st clunking sound	wallace03	Issues \| Warranty \| Recalls / TSB	3	01-10-2013 10:50 PM

02-27-2018, 02:42 PM	#6
jasonojordan Senior Member Join Date: Jul 2013 Drives: 2013 satin white brz limited Location: Cottage Grove MN Posts: 1,049 Thanks: 162 Thanked 511 Times in 326 Posts Mentioned: 4 Post(s) Tagged: 0 Thread(s)	When I had a noise like that it was due to the nut ontop attaching the damper to the tophat was loose.

02-27-2018, 04:51 PM	#12
jasonojordan Senior Member Join Date: Jul 2013 Drives: 2013 satin white brz limited Location: Cottage Grove MN Posts: 1,049 Thanks: 162 Thanked 511 Times in 326 Posts Mentioned: 4 Post(s) Tagged: 0 Thread(s)	60k is not alot of miles but I would deff check out the bearings in them if you are willing to remove each one that is making the noise. What coil-overs did you go with out of curiosity.

User Name		Remember Me?
Password