9 Second 86 Build
 

Base Mods
FBM Walbro 485 Fuel Pump $330.00 Not Purchased http://fullblownmotorsports.com/full...-fuel-pump-kit
Crawford Street Clutch $950.00 Not Purchased http://www.ft86speedfactory.com/craw...l#.VfsRliko7qA
Private Label MFG Header $550.00 Not Purchased https://www.privatelabelmfg.com/mobi...SF-FA20-HEADER
Ft86 Speed Factory Over/Front Pipe $550.00 Not Purchased https://jdlautodesign.net/shop/ft86-3-over-frontpipe/
Greddy Evo3 Catback Exhaust Installed
Cost $2,380.00

Engine
GSC Power Division Valve Springs $375.00 Not Purchased http://www.autohance.com/gsc-power-d...pYjhoCjP3w_wcB
GSC Power Division Intake Valves $136.00 Not Purchased http://www.power-division.com/produc...cat=414&page=1
GSC Power Division Exhaust Valves $224.00 Not Purchased http://www.power-division.com/produc...cat=414&page=1
GSC Power Division Valve Guides $92.00 Not Purchased http://www.power-division.com/home.php?cat=415
Main Bearings $205.00 Not Purchased http://www.frsmod.com/products/fa20-...rs-for-frs-brz
Rod Bearings $155.00 Not Purchased http://www.frsmod.com/products/fa20-...gs-for-frs-brz
Engine Gasket kit $300.00 Not Purchased http://www.frsmod.com/products/fa20-...te-for-frs-brz
Head Gasket $300.00 Not Purchased http://www.frsmod.com/products/dynos...t-frs-brz-fa20
Dynost Case Studds $350.00 Not Purchased http://www.frsmod.com/products/dynos...r-s-subaru-brz
APR Head Studds $200.00 Not Purchased http://autoplicity.com/7586956-arp-2...irShoCI5jw_wcB
Cost $2,337.00

Option 1 High Comp. Engine
JE Pistons 13.5:1 $520.00 Not Purchased http://www.frsmod.com/products/je-pi...r-frs-brz-fa20
Carrillo Rods $1,500.00 Not Purchased http://www.frsmod.com/products/carri...ubaru-brz-fa20
Cost $4,357.00

Option 2 Stroker Engine
HKS Stroker Kit $2,167.00 Not Purchased http://www.carid.com/hks/hks-stroker...eeqhoCCXbw_wcB
HKS Camshafts $1,602.00 Not Purchased https://www.vividracing.com/catalog/...ZIiRoCY7jw_wcB
Cost $6,106.00

Forced Induction
Sprintex 335 Supercharger $5,709.00 Not Purchased http://www.moto-east.com/store/ft86/...c-335-kit.html
NX Plate Kit $720.00 Installed
MSD RPM Window Switch $129.00 Installed
5.7 Larger TB 22030-0S010 $200.00 Purchased

Replace When Necessary
DSS Rear Axles $900.00 Not Purchased http://www.moto-east.com/store/ft86/...-86-hd-pl.html
DSS Aluminum Drive Shaft $405.00 Not Purchased http://www.moto-east.com/store/ft86/...-brz-alds.html
Final Drive 4.44 or 4.67 $750.00 Not Purchased http://www.ft86speedfactory.com/driv...nufacturer=789
Megan Racing Engine Mount $195.00 Not Purchased https://www.ft86speedfactory.com/meg...Q#.Vei-a6Ao7qA
Megan Racing Transmission Mount $66.00 Not Purchased https://www.ft86speedfactory.com/meg...Q#.Vei-x6Ao7qA
Megan Racing Diff Brace $105.00 Not Purchased http://www.ft86speedfactory.com/mega...l#.Vei_PqAo7qA
Megan Racing Diff Mount $130.00 Not Purchased http://www.ft86speedfactory.com/mega...l#.Vei_uKAo7qA
$2,551.00



This is my parts list for my build. If any of you fellow 86 owners have any better part ideas I would love to hear your opinions. My parts list may change depending on what the community has to say about quality and reliability of the parts I havr all ready posted. My end goal is 9 seconds or under, but my real goal is to have the fastest 86 in the states with the fa20 engine still in it.

Good luck ? I think your gona need like 8:1 and 30+ psi to do that?

Why not go turbo? Im going for 9s or 8s as well. Going to keep it a banger car for a while but eventually ill go full retard and throw in a turbo400 or built 4l80 and 4 link 9" rear end.

I'd say 45psi but 30 might do it. I'd also run at least a 70mm turbo, and you might want to look into a new trans...

Fierbuz did 9.96 on 550 hp and time attack suspension with a sequential. Lower compression just compensates for bad fuel. If you got e85 or q16 you dont need to lower compression much.

Yeah and maybe a whole new rear end?

If i decide to do a full on drag car im throwing in a full on solid rear end

Me and my buddies are going to make mine run 6's.

My list consists of the following:
"mad engine mods" (not yet purchased)
"sick ass snail" (not yet purchased)
"Chinese header" (not yet purchased)
"stock injectors" (Installed!)
"stock trans" (installed!)
"stock oil cooler" (installed!)

I came into this thread hoping the car was already built....... :(

If you preload and slip the clutch you dont need a whole new rear end. If u dump and go youll break shit.

I probably going to get a new trans and most likely a fbm rear end, but for now I just have spares lying around for when one gets destroyed so I can still drive the car. Anyone know a good aftermarket trans that fits the 86s. I saw a video of one but I cant remember what it was.

Get a dogbox with an ignition cut on your shift lever so you can shift at WOT without using the clutch

What is a dogbox

Straight cut gears. No synchros