Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB

- Engine, Exhaust, Transmission (https://www.ft86club.com/forums/forumdisplay.php?f=8)

- - Scangauge oil temp xgauge code [Working] (https://www.ft86club.com/forums/showthread.php?t=28374)

Scangauge xgauge code for oil temp, seat belt beep disable, and more

Working code for FR-S/BRZ/86:

Code:

Gauge                          Unit           TXD                  RXF                      RXD      MTH                      Note

Oil temp                       C         07E02101       010702E80324     3008    00010001FFD8    Required FW 4.05 or higher

Oil temp                       F         07E02101       010702E80324     3008    00090005FFD8    Required FW 4.05 or higher

 

Precise Fuel Level         %         07C02129       046105290000     2808    000100010000    Faster refresh rate

Precise Fuel Level    US Gallons   07C02129       046145290000     2808    052900640000    Faster refresh rate

Precise Fuel Level       Liters      07C02129        046145290000     2808    01F4000A0000    Faster refresh rate

 

Seat Belt Beep Query               07C021A7        046115A70000     2808    000100010000   C0 for stock, 00 for disable

Seat Belt Beep Disable              07C03BA700    047B15A70000     2008    000100010000   Should return 0000. Replace '00' in the TXD with 'C0' to go back to stock.

 

Relative Throttle Position      %           07E00145            044185450000         2808     03E800FF0000     

Absolute Throttle Position     %           07E00147            044185470000         2808     03E800FF0000

 

Fuel Pressure                     PSI         07E00123            046105230000         2810     006400450000 

Fuel Pressure                    MPa         07E00123            046145230000         2810     000100010000

Attachment 28549 is the list of supported standard (mode 01) PID for 86/BRZ/FR-S. This list is created from the Wiki’PID, and I highlighted the ones that are supported by our cars.

Here is an example of how to make use of the doc I created:
From the Xgauge cansf list, the short Term Fuel Trim Bank 1 has the TXD 07E00106. The 01 (07E00106) is the mode #. The 06 (07E00106) is the PID. Now look at the doc I attached. It shows the PID 06 is supported, which means that xgauge code works on our cars. The PID 07, On the other hand, is not highlighted on the list. That means the Short Term Fuel Trim Bank 2 is not supported.

Thank you Andery for finding the PID and torque’s code for oil temperature. Without him, I don’t think I can get the oil temp for xgauge.

You are amazing!
Thanks for figuring this out!

Not sure if my the codes would vary by locality, but on my scangauge I had to alter one value in the MTH:
MTH 00010001FFD8

Jonnyboy, thank you for catching my typo. Yeah, it should be 00010001FFD8. It has been a long day. Anyway, the 1st post was corrected.

worked for me... a million thanks!

Sorry for bring a noob. Can you also post the steps to setup in the scangauge?

Thanks in advance.

Edit: never mind, found some instruction online and Weill try it later.

Quote:

Originally Posted by 86•BRZ (Post 718128)

worked for me... a million thanks!

The IA is intake air temp?

What's WT, water?

I've had my eye on the ScanGuage for quite awhile, this is great. By the way, will the Scanguage fit in the slot under the a/c controls? It looks close, maybe not for the push button start equipped cars but perhaps the ones without.

Quote:

Originally Posted by R2 (Post 720414)

http://www.scangauge.com/image-resou..._with-dims.jpg

Sent from my iPhone using Tapatalk

Quote:

Originally Posted by mr_m (Post 720430)

http://www.scangauge.com/image-resou..._with-dims.jpg

Sent from my iPhone using Tapatalk

Boom. There it is, thanks. :thanks:

You can set the The ScanGaugeE the same right? Since is more than an 1" shorter should fit b/w start button and usb

Sent from my iPhone using Tapatalk

Quote:

Originally Posted by mr_m (Post 720463)

You can set the The ScanGaugeE the same right? Since is more than an 1" shorter should fit b/w start button and usb

Sent from my iPhone using Tapatalk

So I couldn't find my tape measure but with a shitty ruler I found that there is plenty of width for the standard unit. However, height is an issue and you may have to remove or trim the rubber in the slot. The height of the slot without that rubber is over 1.5" though so it can work. My other concern is the display contrast - can you see the display clearly from the drivers position if it were installed there flush with the dash?

Quote:

Originally Posted by Synack (Post 720391)

The IA is intake air temp?

What's WT, water?

yep, exactly right

here is a pic I found on these forums somewhere

Ill have to look into the scangauge E, hopefully it will fit in the start button models. I pinched this scangage from my other car anyway..