TIC BRZ 1st on KONI'S
 

TURN IN CONCEPTS 2013 SUBARU BRZ

Order Date:5/07/2012
Estimated Delivery:7/6/2012
Changed Estimated Delivery:9/14/2012
Arrival date: 9/17/2012

Purpose: Shop Car/ Daily
Purchased: Busam Subaru
Weight:
Motor: 2L
Power: 200hp/150tq
1/4 Mile: HAha

https://lh6.googleusercontent.com/-B...s350/photo.JPG

So the car finally came in! 4miles on the ODOM on pick up.
We all took it for a test spin then on the rack she went.

https://lh3.googleusercontent.com/-d...0/DSC_5339.JPG

MODS

Installed Installed

Yet to be installed


Suspension:
Turn in ConceptsSteering Rack Bushings
Koni's
Racecomp Engineering Tarmac Springs
HVT Non Raising Camber Plates
Whiteline Rear Lower Control Arms
Front Camber Bolts
Whiteline Rear Subframe Bushings
Whiteline 22mm Front Adj Sway Bar
Whiteline Front Endlinks
Whiteline 18mm Rear Sway Bar
Kartboy Rear Endlinks
Whiteline Front Control Arm Bushings
MSI Rear Toe Arms

Drive-train:
Southbend Stage 3 Endurance Clutch Kit
Southbend Flywheel
TIC Group N Engine Mounts
Kartboy Rear Stay
Kartboy Trans Mount Insert
Kartboy Short shifter
Whiteline Rear Diff Mount Bushings




Brakes, Tires, Wheels:
18x9.5 Linea Corse Lemans - Silver w/ Polished Lip (5x100/e30/73)
Hankook RS3 255/35/18
Hawk Hp+ Front Pads
Hawk HPS Rear Pads
RBF600 Brake Fluid
Motive Autowerks Master Cylinder Brace

Engine & Exhaust:
Kartboy Crankshaft Pulley FA/FB


Aesthetics:
TIC Oil Fill Cap
Custom TIC WC Lathewerks Shift Knob[/COLOR]

PHOTOS

https://lh4.googleusercontent.com/-8...0/DSC_5349.JPG


https://lh4.googleusercontent.com/-z...0/DSC_5350.JPG

https://lh4.googleusercontent.com/-G...5281%2529.jpeg

https://lh3.googleusercontent.com/-T...5283%2529.jpeg

Excellent, glad to see you guys here.

Yay! TIC and redheads....

- drew

sick wheels

So we have been a little bit busy thus we are a little late to the ball game on our journal.

We have some mods that we have done so far that I will be doing a little updating on a little at a time then from here out updating with each future Mod.

Stock VS Rs3's
https://lh5.googleusercontent.com/-q...0/DSC_5338.JPG

18x9.5 Linea Corse Lemans - Silver w/ Polished Li (5x100/e30)
We wanted something that would be a little aggresive for the BRZ yet work for us from a performance stand point so we went out on a limn on this one, wheel dude helped us out on getting these wheels.
https://lh3.googleusercontent.com/-g...0/DSC_5337.JPG

https://lh5.googleusercontent.com/-O...0/DSC_5350.JPG

Putnam??

If so :party0030:
http://www.ft86club.com/forums/showthread.php?t=18110

I'm excited to see what you guys do with it. What camber settings are you running with your wheel/tire set up? Any fender mods?

any rubbing issues with taht setup guys? i'm looking into 18x9.5+40 with a 255/35 starspec and my buddy is telling me i should go to a +35 instead. car will be on coilovers..

We are running -2.7 camber front & -1.7 rear
There is some slight rubbing in the rear on VERY fast large bumps on the highway. The tabs on the fenders in the rear have been trimmed lightly. No modifications up front needed (with or without camber plates).

Exhaust
So far we have had two exhaust on the car other than stock. Both we have liked very much in one way or another.

Mach-V
The first exhaust that was installed was the Mach-V BRZ/FRS Muffler Delete Pipe
http://ep.yimg.com/ca/I/fastwrx_2228_129900164
You can find our review on this exhaust HERE!

Nameless
After a few weeks our second exhaust came in. This is a Custom Nameless axle-back muffler delete.
https://lh3.googleusercontent.com/-7...0/DSC_5357.JPG

Great looking wheels! How much do they weigh?