Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB

Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB (https://www.ft86club.com/forums/index.php)
-   Suspension | Chassis | Brakes -- Sponsored by 949 Racing (https://www.ft86club.com/forums/forumdisplay.php?f=59)
-   -   One Side Lower = Normal? (https://www.ft86club.com/forums/showthread.php?t=118292)

Taka 05-05-2017 08:58 PM

One Side Lower = Normal?
 
Just a quick question. I got some lowering springs installed that have been on the car for about 1 month now.

One thing I noticed is that the Rear Driver side sits 2mm lower than the Rear Passenger Side.

Is that normal? (All my tires are inflated to the same PSI all around)

ryoma 05-05-2017 09:05 PM

make sure the spring is sitting correctly on the spring perch. there's an indentation on the perch where the end of the coil should be. (at least for the front, I don't remember on the rear)

Taka 05-05-2017 09:50 PM

I'll have a look at it tomorrow. Thanks bud!

Tcoat 05-05-2017 11:28 PM

Quote:

Originally Posted by ryoma (Post 2905344)
make sure the spring is sitting correctly on the spring perch. there's an indentation on the perch where the end of the coil should be. (at least for the front, I don't remember on the rear)

There is on the rear as well. This seems to be a relatively common issue when spring are installed.

Gforce 05-06-2017 09:38 AM

How did you measure such a tiny amount?

There is zero probability that ride height for all four springs will be the same within 2 mm.

Factory fresh stock springs aren't usually within 5 mm.

You will realize that as soon as you get into the car the left side springs will get "shorter"?

cjd 05-06-2017 10:35 AM

Drive the other 3 corners up onto 2mm platforms and it'll even out... roughly.

Unless you KNOW you're on a surface that is both perfectly level and flat, it's entirely likely that your measurements aren't all that accurate. In my garage, which sure feels like a flat smooth surface, the platforms are at ~-3mm, -26mm, -29mm... and that's just centerline differences.

Check the spring mounting, but I'd bet that it's the surface as much as it is anything else.

Also... after balancing, I definitely do not have exactly the same ride height all around... but that's to be expected. So it's not a bad thing inherently, no matter how you look at it.

C

Taka 05-06-2017 10:47 AM

Thanks for the advice and comments.

I've also contacted a shop I go to and they told me it's normal on springs to have a difference between 2-3mm.

I'll have them check it out also just for reassurance when I visit them for some things next week.

I'll also have a look at it myself today.

Thanks again everyone!

Gunman 05-06-2017 02:38 PM

2mm is well within tolerance.

MurderousPandas 05-06-2017 05:17 PM

It is possible that weight on the inside could be leaning to one corner. In my Integra, if anyone sat on the car or put anything more than 50lb in the car, you could see the car lower on whatever corner is closest. I had soft springrates at the time, but still something to consider if you have some luggage in there.

Sent from my HTC6535LVW using Tapatalk

Racecomp Engineering 05-06-2017 05:19 PM

Normal. And normal that the driver's side is the lower side.

- Andrew


All times are GMT -4. The time now is 11:51 PM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2026, vBulletin Solutions Inc.
User Alert System provided by Advanced User Tagging v3.3.0 (Lite) - vBulletin Mods & Addons Copyright © 2026 DragonByte Technologies Ltd.


Garage vBulletin Plugins by Drive Thru Online, Inc.