Big power fa20 parts/trans swap
 

Sold:
motor mounts
darton block
cylinder heads
pistons/rods
head studs
Ecutek
Intake manifold


Parts are apart and ready to go. Location is 21108 for local pickup or plus shipping. Engine parts are less than 500 miles, all in working condition with no issues. If anything was questionable, I wouldn't have it for sale.

Darton sleeved block. Has machined lip so the sleeves can not drop. Stock bore, no scratching or gouges. Light hone for ring seating and it's ready to go. No over bore required. Arp main stud kit installed. $1500

Oem heads with oem cams. Ferrea comp valves, ferrea dual springs and retainers. Decked before install, still looks perfect. Comes complete, all valves are shimmed to perfect spec. $1300

Manley turbo tuff rods with arp 625+ hardware
Je 9.5 Pistons with their largest wrist pins. $750 for the package

Fuel injector clinic 1650cc w/ plug and play harnesses. $700

Full blown intake manifold. $850

Full blown t4 turbo manifold. $600

Full blown fuel rails (no lines). $200

Custom arp L19 head studs. $200

Cusco motor mounts (not pictured). $160

ecutek cable/dongle. licensed to my stock ecu (new license required). $150


Complete tremec trans swap. Will take whatever an fa20 can throw at it. $6000

Faceplated tko600 with heat treated gears for shock absorption
Custom crossmember with poly mount (need to drill 6 holes)
Custom shifter setup (very minimal trimming, nothing visible inside the car)
Custom drive shaft shop aluminum driveshaft with chromoly tremec yoke
Custom fa20 to tremec bell housing
4 puck single disk clutch
Clutch master twin disk clutch (awaiting revised flywheel from cm)
Custom throw out bearing assembly and shift fork, uses oem slave cylinder
Tilton hydraulic throw out bearing setup (can use either setup)

http://i3.photobucket.com/albums/y51...pswrf9pzlf.jpg

http://i3.photobucket.com/albums/y51...pspys0ex7x.jpg

http://i3.photobucket.com/albums/y51...psumkeox2d.jpg

http://i3.photobucket.com/albums/y51...psty6z7e5l.jpg

http://i3.photobucket.com/albums/y51...psulzx7otb.jpg

http://i3.photobucket.com/albums/y51...psxzmittm2.jpg

http://i3.photobucket.com/albums/y51...psted9gpk5.jpg

http://i3.photobucket.com/albums/y51...psjefra0pn.jpg

http://i3.photobucket.com/albums/y51...psbhnwovva.jpg

http://i3.photobucket.com/albums/y51...pspfclfwbq.jpg

http://i3.photobucket.com/albums/y51...pshxyxq4lh.jpg

http://i3.photobucket.com/albums/y51...psvdzxpxsa.jpg

http://i3.photobucket.com/albums/y51...psfpbokaac.jpg

http://i3.photobucket.com/albums/y51...psozqtnbtt.jpg

http://i3.photobucket.com/albums/y51...psylkaynbh.jpg

http://i3.photobucket.com/albums/y51...pskhu0smak.jpg

http://i3.photobucket.com/albums/y51...psqnqfjw7x.jpg

http://i3.photobucket.com/albums/y51...pstnzarmeg.jpg

pmed on most of the motor stuff

pending sale:
motor mounts
darton block
cylinder heads
pistons/rods
head studs

also have an ecutek cable/dongle. licensed to my stock ecu so you'd need a license when buying a tune. $150

Subscribing! Depending coin and if they are sold before I can afford, interested in piston/rods and engine mounts. Don't want you to hold them though

PM sent

Engine block, heads, pistons, rods, head studs, ecutek are sold. Mounts are pending

mounts and intake manifold are sold. still have:
trans kit, fuel rails, fic 1650's, t4 turbo manifold

^

still have parts. also have a full blown fa20 to v160 adapter plate kit

Fa20 to v160 adapter plate. $500 shipped

http://i3.photobucket.com/albums/y51...psg9xss1by.jpg

http://i3.photobucket.com/albums/y51...psm9vz3zrg.jpg

http://i3.photobucket.com/albums/y51...ps9hvzlauh.jpg

FIC 1650's, plug and play $650
full blown fuel rails (no fittings) $140
full blown t4 turbo manifold $575

go fast!

still have

fic 1650 plug and play setup
full blown fuel rails
full blown t4 turbo manifold
full blown fa20 to v160 adapter

also looking to sell my full plug and play motec m150 setup. includes customer jumper harness with gps connector, shift light module connector, connector for additional inputs/outputs. m150 ecu with license, and custom fa20 firmware that has basically any feature you could want unlocked (boost by gear, launch control, anti lag, traction control, rolling launch, etc). looking for $5200 for the whole package.