OBDII (OBD2) Connector
 

We've had a discussion here on the Oz/NZ regional forum but wondered if you guys/girls in USA and other parts around the world can assist.

We are looking at using the OBDII connector to get real time oil temp. Any of you managed to get this reading using the connector and an android or iPhone app or similar.

Appreciate any help on this as we can't find the answer on the forum.

Thread was here
http://www.ft86club.com/forums/showthread.php?t=23232

Aslong as the car has a factory sensor for that specific reason, you should be able to tap into it using the torque app for android, although cars are rarely fitted with that sensor, and I'm not sure if the FRS/BRZ/86 have it.

Maybe you guys can help answer my very similar questions LOL;

http://www.ft86club.com/forums/showthread.php?t=23391

I have seen the data available to monitor using toyota's techstream tool and oil temperature is available.
however, when connecting and aftermarket reader (dashcommand in my case) this parameter does not show.
In short, there is a sensor for oil temperature and is monitored by the engine ecu, however it might no be seen by stardard obd2 readers.

Unfortunate, I'll know in a couple weeks if this is true or not for me. Trying to avoid getting a gauge for oil temp. Although it might just be necessary to always know what temp it is being that I'm boosted.

Would you be able to see results from that techstream tool again and possibly indentify the PID for the Oil temp, with the PID we'd be able to add it in torque and get the info, and the reason you don't see it on the standard obd2 readers is simply that, because it's not a standard obd2 code >:( there also refered to as Vehicle Specific or Manufacturer Specific PID's and basically hardly anyone has access to these specific pid's except scantools such as techstream that pay top dollar to have them..:(

@Brody602, @driver01, @Synack and anyone else interested:

Damn, tried the kiwi2 plx wifi connector with all the iPhone apps that seem compatible AND the ELM327 with three android apps and NONE showed real time oil temp.

Then tried the oil temp PID from Wikipedia and no data received.

So, looks like my earlier solution with the HKS OB-Link is the only way I can see to get real time oil temp. Cost is approx US$300 for the OB-Link, the carscope app is free, and if you have an android phone that is all you need other than a suction mount for your android phone that you can get cheap from eBay. At this stage the HKS OB-Link is not compatible with iPhone.

For a really nice look you can link to an installed 7" tablet in your dash or suction mount to the screen.

I see there's also some really expensive JVC and Pioneer head units that may allow their touch screen to control the android app and that would be pretty cool.

Bad news is that unless someone else can work out a solution the cheaper ELM327 and Kiwi plx connectors won't give you real time oil temp and the cost of the OB-Link is pretty steep if that is all you want it for.

Sorry I can't be of any more help unless some IT geeks have anything else to try. :iono:


.

Anyone tried the torque scan addon?

Happy to try it for you.

Is this what you mean?
https://play.google.com/store/apps/d...rquescan&hl=en



.

yup, it takes quite a while to run but it could find some extra PIDs?!

Ok, have just tried the torque app with the torque scan add-on with the ELM327 Bluetooth connector.

Shows in green each piece of data that can be read. Unfortunately "Engine Oil Temperature [5c]" is in white and says "No data received".

Only thing I can't try is the torque app and torque scan with the Kiwi2 plx connector as I only have the wifi iPhone version and the torque app is android only. But, it seems from the iPhone apps I have tried that the oil temp is not read by them either.


.

I guess I'll just buy a real gauge and call it a day.

Yep, although the HKS OB-Link is awesome so if you want to measure stuff over time and be able to select different gauges it is still a good option even if pricy.

A gauge will need to be wired in rather than using the OBD2 connector unless someone can find the PID for oil temp. HKS must be using the non-standard Toyota oil temp PID and if we can find it out...

Here's my samsung 7" tablet running carscope paired with the HKS OB-Link. You can see oil temp is one of the gauges I have selected and it works perfectly.

http://iforce.co.nz/i/p5a3utup.dw3.jpg

Has anyone managed to get the OBD2 working through an IPAD?

Yes, I have it working with the with the kiwi2 plx wifi connector.

Assume it will also work with the ELM327 wifi version. Then, you can buy an iphone app such as Rev for iPhone etc - lots to choose from.

You still won't get oil temp, if that's what you're after, unless we can track down the toyota non-standard PID code.


.

Being boosted I absolutely need to know what my oil temp is at all times.

Finally an oil temp gauge that reads through the OBD2 connector.

Mounts in drivers side aircon vent but still allows the air flow

http://pivotjp.com/product/dual-gauge/img/DXW-e.pdf


.

Did you chaps see this! Oil temp PID

http://www.ft86club.com/forums/showp...&postcount=123


.

Has anyone used this on dash command

Need help with the object settings.

Won't work on dash command unfortunately so no iPhone support.

See discussion with dash command asking them and their response here
http://www.palmerperformance.com/for...p?topic=6351.0


.

Thanks, I added a post there requesting it :thumbsup:

Scangauge can be setup to read oil temp

http://www.ft86club.com/forums/showt...ight=Scangauge

Here are photos with the ipad mini with dashcomand... Hope someone post a way to make it read the oil temp...

...

;

Uh... where are your HVAC controls?

if you're hot open the window. if you're cold put a jacket on

:iono:

They are behind... Just lift it up, adjust anything and then slide it down.

As many of you will know you cannot currently add the oil temp PID for the twins to Dash Command to get oil temp to show on an iPad or iPhone even though we now know the oil temp PID.

Best option at the moment is to use Torque on an Android. Not good for iOS users.

If you use an iPhone or iPad and want to be able to see oil temp gauge using dash command PLEASE go to the developers Dash Commnd forum and add you voice to the request thread here.

http://www.palmerperformance.com/for...pic=6351.0;all

They are looking at adding Toyota/Subaru specific sets of data but also other makes. The more of us that request either being able to add specific PIDs or a Toyota/Subaru set the more likely we get to the front of the queue for development.

Also a good idea to write an app review of Dash Command and tell them you have voted it down due to no oil temp for the 86 or BRZ.

Let's get the FT86 Club to put the pressure on their development team! 86ers are go!

.

day shot plz? this may get me to buy an iPad mini (cheaper then a bunch of gauges installed)

Daytime pic... It is a holder I made myself; it got two rails behind so you can lift it and access the climate controls

I'm making a mold to make it look more OEM... I'll post pics when finish

If you won't want oil temp on dash command so it will work on an ios device make sure you follow steps here!

http://www.ft86club.com/forums/showp...2&postcount=28

.

im def adding 1 or 2 gauges, but this will be great instead of trying to add like 6

Can we get some pics of how the rail attaches to the car?

I just use the principles of this video... but of course, I just used two bars of half inch and polish to the that it does not demage the radio bazel... Tomorrow I can add a pic of mine so you can have an idea and add it the way it is better for you, but the mold I'm trying to make will look a lot better.

[ame="http://m.youtube.com/watch?v=p0yonQ-2PFY"]indash 2020/In-Dash(insert) mount+Universal Holder for tablet PCs, as iPad Mini, Galaxy Tab7.7, etc - YouTube[/ame]

Also... This is the holder that I bought from ebay... But just use the main holder, I discarded the rest

http://item.mobileweb.ebay.com/viewi...id=05975372426