Where to buy Whiteline Camber Bolts
 

need to buy a set asap

Look in the marketplace and PM some vendors.

Or just get some SPC bolts from your local parts store for $40 less.

got mine from a site called energysuspension

go to rockauto and buy camber bolts for whatever subaru you want. Or tougetuning has them for pretty cheap.

I am getting conflicting info. Some books are saying it is a 16mm bolt, others are saying 14mm. The 16mm bolts are on backorder from what I see, the 14mm stuff I have in my warehouse in NY, Eibach brand.

Whiteline part number KCA416 is on a special order basis at two of the big Whiteline distributors

Adam

i need at least -1.5 degreess

I am talking about the diameter of the bolt 14mm or 16mm. All the camber bolts will give that much adjustment.

its a 14mm
what brand do you have in stock and how much>

Eibach part number 5.81260K. Same as WRX/STi.

$20 at the store.

Just make sure this part number will work, because they don't have it listed as an application.

I'm pretty sure it would work, Eibach and SPC share the same parts on some camber kits i know the Eibach camber kit for my TSX was the same as the SPC kit.

I'm using a 16mm bolt in the upper bolt of my brz, same as your frs
You can use the 14mm ones but there is alot of play. I returned mine and got KCA416; fits much better since the oe bolt has a 16mm shoulder

14mm would go in the lower hole.

No problems getting the tabbed washer completely perpendicular to the strut with the 16mm bolts? I was slightly concerned that the hole on the flange side of the strut would be 16mm but the hole on the nut side would be 14mm, in which case the aftermarket bolt wouldn't work quite right.

I carry the Whiteline bolts. Whiteline lists the KCA414 as the fitment for the car. I have them in stock. KCA416's are special order, but I can get those too. Personally I don't use them as between the adjustment in my KW's and the C-com offset upper mounts I have, I have no need for the camber bolts (which is why I have them in stock, I bought them "just in case").

My understanding was that the top bolt is 16mm but you can use a 14mm straight bolt in its place and the play that you get is your camber adjustment. I believe this is what's outlined for factory-style alignment.

The eccentric bolt (16mm I think) would go in the lower hole.

Correct me if I'm wrong, I seem to hear conflicting reports on this.

Top hole is 16mm and bottom hole is 14mm.

I am just using Subaru 14mm crash bolts on the 16mm top hole, so gaining camber by the smaller bolt having room in the larger hole.

From looking at eccentric camber bolt pics, it seems the "lobe" would probably be 16mm (max that can fit the top hole) and the "shaft" would be something smaller like 14mm?
I would think that allows greater adjustment than the 14mm straight crash bolts, since you not only gain camber from the smaller bolt in the larger hole like the crash bolts, but also have the lobe part to push the hub even more inward.

sorry, both bolts upper and lower are the same, and the correct application regardless of what ever may be listed is the KCA416, it goes in the upper hole.

You do NOT take out a shouldered 16MM bolt and replace it witha loose fitting 14mm, not on my car.
you DO take the 16mm andreplace it with a KCA416

Its your car and your safety..

Where did you get your KCA416s from? Most everywhere I look they only have the 414s..and whiteline wants $80 to ship them here..which is obscene.

we have them in stock. Pm us if your interested.

I just got my 16mm camber bolts installed today. I ordered them off nissanraceshop.com. excellent service. They had overcharged me by accident and i didnt even know it until they called me to tell me. they refunded the extra charge and overnighted the bolts to me! i would recommend them!

too expensive for camber bolts

click on the word camber bolt in my signature

i got mine @TiTAN Performance for cheap price :)

yea but the 14mm

try their website. They have a few dealers in NY.
http://www.whiteline.com.au/dealer2012.php

I found them and for a really good price :)

I haven't taken the upper bolt out of my BRZ yet but many cars have a slotted or oblong upper hole,(taller top to bottom) which allows for a 16 mm bolt to fit into a 16 mm hole even though there is a lobe that would be larger than 16mm. As you then rotate the bolt, the lobe pushes on the slot and moves the hub in and out. Hope that helps you understand how they work. Don't think I'd put a 14 mm bolt in a 16 mm hole. It isn't as safe and fine tuning the adjustment would be much harder than it needs to be if you have the correct part.
If someone can confirm that the upper hole is slotted, (oblong) then this pair should work. Ingalls part number 81260 $25 - free shipping at Amazon.
[ame="http://www.amazon.com/Ingalls-Engineering-Caster-Camber-Adjusting/dp/B001UCD6ZS/ref=au_as_r?ie=UTF8&Make=Subaru%7C13&Model=BRZ%7C2 1598&Year=2013%7C2013&carId=002&n=15684181&newCar= 1&s=automotive&vehicleType=automotive"]Ingalls Engineering 81260 Caster/Camber Adjusting Kit : Amazon.com : Automotive[/ame]
Ingalls also makes adjustment bolts for non slotted 16 mm applications.

Update:
 

I now have better info and need to update the info I gave out in my first post right above this one.
I took out both the upper and lower bolts and inspected them and the hole they came out of. Both holes are round and not slotted as I thought they might be based on prior experience with other manufacturers. Since they are round, Any bolt with a lobe that makes the bolt larger than the size of the hole will not fit. The bolts are definitely not the same as someone posted earlier. The lower bolt is straight and is 14 mm. The upper bolt is both 14 & 16 mm. The first inch or so is 16 mm and then tapers to 14 mm. The upper hole is 16 mm all the way through so the bolt only makes contact with the hole for the first half, then it's in the air for the other half. Anyone knows that a chain is no stronger than it's weakest link. That being the case, the bolt isn't much if any stronger than a straight 14 MM bolt in my opinion. If it were to break, (very unlikely) it would fail at the point that it tapers down to 14 MM. After seeing this, I have changed my opinion and now think that the 14 mm bolt is nearly the equal in strength and should be no safety issue. Don't sue me, It's just my opinion but I would have no qualms about driving with it. There is simply no way with out running you car in to a stationary object to snap this bolt if torqued properly. I don't care what kind of sticky tires you have, you can't generate enough load to break these bolts. Still, adjusting camber with a 14 mm bolt in there will be trial & error until you get lucky and arrive at what you are looking for. I'd still recommend a 16 mm adjustable camber bolt but it needs to be one designed for a round hole. You can find them at the amazon link above and I'm sure many other outlets. Hope this helps.

https://corner3garage.3dcartstores.c...BRZ_p_460.html

I'm pretty sure every vendor with an alignment rack has them in stock for your car!

At least the should!