What Manual Trans Fluid Do You Use?
 

So I know this topic has been talked about quite a bit in the other sections but I want to get some info from my fellow Canadians. I have done it once already, switched over to Amsoil, but I don't think it did too much. I've been running it for a year now and I think my 2nd gear grind is getting worse. The winter makes second gear a real problem I basically have to skip second till the car has warmed up for a good 10 minutes. So my real question is, for those that changed their transmission fluid what has worked the best for you? And do you think at this point the problem might be just an issue with the trans?

Thanks in advance for any answers :thanks:

I have the exact same problem and I now run Redline. Shifts smooth as butter when its hot but when cold the second gear crunches and grinds are unbearable.

When it first started getting cold I left the car with Subaru over night and they took it for a few test drives and told me it is just "normal Toyota gearbox noises" and "it must be you not pushing the pedal all the way down".

I occasionally look into it when I have the chance and the only thing I have found so far to minimize the crunches is to raise the clutch pedal back up (I had adjusted it down in the summer as per the DIY). Other then that I am in the same boat of double clutching or skipping second all together when its cold.

Redline, feels way better, especially when warm. That being said, the moment temps are below -5, crunchy crunchy unless I double clutch in 2nd

Subbed.

For the most part second gear is OK for me. At least I've found a way around it. However downshifts into second gear suck for the most part no matter what I do (feels more like clutch related than gear box) and my 6-5 downshifts crunch like a mofo no matter what I do post an OFT flash which is strange to me.

But subbed to know more about what other people in cold climates are using both on the street and track.


Sent from my iPhone using Tapatalk

Totaled.

Got to buy an auto now.

A while ago I read a thread on here that the engineer who designed the gearbox knew about the issue. Something to do with performance vs lose gear gap. As cold weather expands and contracts the metal makes it difficult to actuate it into gear

Also how many Km's are you guys changing the fluid?

found the link: http://www.ft86club.com/forums/showthread.php?t=31929

I thought we were talking about auto gearboxes?

🤣🤣

Jks


Sent from my iPhone using Tapatalk

So far 13,000 km from new. Metal shavings present, but nothing too crazy compared to most new cars that I see.

Motul Gear 300 for me in both the gearbox and diff (same fluid, not running the 300LS in the diff since it's not a clutch LSD).

I still get occasional 2nd gear crunches when cold, but it's not every shift even in the dead of winter.

Pentosin MTF2. I've tried a few different fluids, and for my FR-S, it seems to work best. I have not tried Motul, or Redline's MT-85. I've had my car since June 2012, it has over 100,000kms on the clock, and it is my daily driver year 'round in Southern Ontario.


Most car manufacturers put Canada in the "severe service" category for maintenance scheduling...with that in mind, the recommended interval for manual transmission fluid changes is 24,000kms/2 years. I change mine every spring.

Just about everyone raves about Motul gear 300 but I was reading in one of the threads and a member said it was horrible to drive in the cold with it. I was thinking that was going to be my next fluid to try though.

Do you find that it still grinds at all in the cold? or downshifting is hard? I mean I've only had this trans fluid in for a year/ 14,000 km so I didn't think it would be this bad

I have motul gear 300 in mine and on cold starts 1st to 2nd is very very difficult. Once warm is gets much better. Im planning to try out https://www.amazon.com/dp/B002INX20C...N5VX4S7G&psc=1

For my next transmission fluid.

Only on the first shift or 2 when it is really cold...I've never had a problem downshifting. With any fluid, the trans should have some time to warm up before the best shift qualities are present. This fluid will "warm up" faster vs. stock due to the lower viscosity. It will be fine for a daily driver...if you plan on tracking the car, it may be safer to stay with the recommend 75W90.
I tried Redline MT-90...it was an improvement over stock, but the crunch was still there (even with a fair bit of warm up and some gentle driving).

Maybe I'll give this a try instead of the Motul. I understand that the trans needs time to warm up but I mean sometimes my car will still grind/ crunch all the way up to operating temperatures

some numbers.


i drained the original fill at 4900 miles an pumped in Subaru 75W-90. per the manual, slightly more rattle from the syncros and similar frustrating cold characteristics.


i will switch to ptx as i use it in another car....which shifts well from cold and it is compatible with yellow metals. 40ish a liter but cost per mile is trivial with normal drain intervals.
http://i41.tinypic.com/19rsrc.jpg

Trying another new oil and like it
 

I purchased a 2013 FR-s in October of 2017 with 16,000 miles to do SCCA Autocross (SSC) and a couple of track days. With the way I abuse cars I change all the fluids yearly and the engine oil about every 3,000 miles, which I know is way to early for synthetics, but I do it anyway. Last spring I changed the tranny and diff to Redline noticing quite the crunch threw 1st, 2nd, and 3rd in the cold until it would warm up. I live in the midwest so we did get some negative degree weather. This past Saturday I changed out to Motul 300 for both tranny and diff again (now 24,000 miles on the car) and there is much less crunch and feels great when warm. I will say that we have not had any real cold since Saturday so I can't truly compare but in the low 40's the Motul definitely crunches less than the Redline. For this car I will not be going back to Redline fluids even though I ran it for 20 years in a Honda CRX MT but that is a different beast and was an Autocross trailer queen.



Hope this helps.

Motul 300, almost completely resolved my crunchy gears at below 0f temperatures.

May I ask where that data came from?


I tracked with Motul Gear 300 last summer and found my shifts were slow and notchy, so I'd really like to try something else.

Curiously, a buddy of mine ran this in his FRS:

https://www.amsoil.com/shop/by-produ...n-fluid-5w-30/


Amsoil Synchromesh - however reading about it, they spec it as a 5W30 fluid!


The Amsoil WEBsite recommends their 75W90 fluid for this transmission.

I replaced my stock fluid with Polaris Slingshot transmission fluid: https://lubricants.polaris.com/en-us...cants/2879440/


Harder to find GL3 but that is what the service manual recommends. 2nd gear is still a bit notchy below freezing before warming up, but better than before, and now completely smooth once the car is up to temp.


The 75W-90 GL3 oil looks / smells very different from the Redline 75W-90 GL5 I put in the differential. I noticed on draining that the trans / diff oils were quite different as well.

Same stuff for gear box and diff.

Hi Folks,

Any gearoil recommendations for the -40F here in Alberta Canada?

Anyone know where I can pick up pentosin MTF2 in the GTA? Also what viscosity do you guys run for this oil?

2nd gear grind...
I've barely had this problem but when I do its my fault not the oil lol. My friend complained about the same 2nd gear grind and I asked to drive his car. I had no issues while driving his BRZ so our conclution came down to he needs to practice on his shifting lol.... not saying this is the case with everyone but it might be the issue for alot of guys...
Perhaps you're shifting too early (shifting before 3000rpms will result in clunkiness) releasing clutch too early/not depressing cluth enough, car hasen't warmed up enough or you could have metal shavings....
I stick with Motul Gear 300 75w90

Bought my 2016 used last June with 27000 kl. I assume it had the original fluids in the tranny and diff. as it was dealer serviced by the previous owner.
I experienced no shifting issues whatsoever. Was planning to do HPDE & Lapping so I changed out the fluids to Motul 300 in the tranny and 300LS in the diff.
Immediately I experienced shifter stiffness and clunking going up into 2nd gear for the first few blocks each morning then it is fine. This at all temps, in fact it's stored in the winter so it hasn't been driven (by me) at freezing or lower temps.
Frankly, if it bothered me I'd switch back to OEM tranny juice first before gambling on other aftermarket brands.

I switched to Pentosin MTF2 (75w80) after a lengthy thread in this forum going over its qualities and its connection to Aisin transmissions. I did it at 40k and I have over 10k on it since. I cant argue with the results. Shifts are smoother, especially in the cold. (0F-50F) It comes factory in BMW M3's, and you can also buy it from Hyundai dealerships because it comes in the manual Genesis. The only downside is the price. Its usually around $25/qt retail.

http://www.pentosin.net/specsheets/Pentosin_MTF-2.pdf

How much tranny fluid do you need to buy for fluid change?

manual transmission fluid change
 

i have about 1000 miles on my manual transmission new fluid. The tranny was getting really notchy, i bought the car with 40k miles on it and i am thinking it was never changed, i tried Redline MTF and so far it is tons better and almost completely eliminated all notchiness except a cold start ups for the first few minutes, i really haven't encountered any really cold temps < 30 degrees F yet so i am wondering how its gonna be this coming winter. but so far i am happy with it

Any End All, Be All Answers to what works best?
 

Just bought my used 2017 BRZ with 8,000miles in November. I absolutely love this car, even though it has less power than my '02 WRX. Been having the same issue with second gear crunch as the weather got colder. The BRZ does great after it has been driven for about 10 minutes and the oil in the transmission has warmed up.


So after reading many posts, from all the sites, about the BRZ/FRS/86 6 speed manual transmission, I came to these conclusions:


1 - It was recommended to stick with OEM Subaru transmission fluid.
2 - It needs to be a GL-4 rated oil (due to the bronze & copper rings in the transmission)
3 - Change all the fluids as soon as you get the car. Transmission oil drain magnets seem to always be gunked up with a ton of metal shavings from the original oil.



I made my appointment with Subaru for this past Monday, to change engine, transmission and rear axle fluids. They neglected the transmission and rear axle because it wasn't necessary yet (22,000 recommended) so I had to bring the car back the next day to get them done.


Got in the car, sat at the dealership for about 5 minutes and then started to drive. Pulling out of their parking lot into traffic, I could not even shift into 2nd gear. Felt like someone put a block in to prevent it shifting. As the transmission warmed up from driving, shifting did get better.


I was expecting that the oil change was going to drastically improve the shifting, but it is now far worse than it was. On these cold Mid-Atlantic days, it takes 5 to 10 minutes of driving to get the transmission oil warmed up to where the car has fewer issues with 2nd gear. But I have also noticed that while the transmission oil is cold, I have a slight catch when shifting out of 1st gear, besides not being able to shift into 2nd gear. Been doing more 1st to 3rd shifts till the car warms.



I looked at the Subaru invoice and it turns out they used OEM GL5 80W90 for both the transmission and the rear axle. Great, they did not listen to my request for using a GL-4 in the transmission.


So, sometime this week, depending on the temps here, I am going to get my BRZ jacked up, drain the GL-5 oil currently in the transmission and put in:
Red Line MT-90 GL-4 Full Synthetic High-Performance Lubricant for
Manual Transmissions and Transaxles


This was recommended in several of the posts as working on the 2nd gear issue.


I'll see how that goes and report back with my observations. Maybe a plug-in heater for the transmission is needed for winter driving. :sigh:

Changed Transmission Fluid this afternoon
 

The weather cooperated this afternoon, I got the BRZ up on stands and proceeded with the operation.


As I noted in the previous post, I had the Subaru dealer replace all the oils in the car last Monday/Tuesday. Stole a couple of the oversized pee pads the wife used to use in the cat's litter box, spread them under the car, got my oil catch can out and took out the top fill plug on the transmission.


**Possible problem: When I removed the fill plug, oil immediately began to flow out! I thought I had spaced out and removed the bottom drain plug by accident, but I hadn't. Don't know how the dealership did it, but there was an excess of transmission oil in the transmission. Below is a picture of the car on stands to show that I was level when doing this.


Not sure if this added to the dilemma of 2nd gear shift or not but there should not have been this much extra fluid in the transmission. Judging by how much was in the catch can, I would guesstimate approximately 12 to 16 ounces of additional fluid.


From there, I removed the drain plug, drained the oil, replaced the drain plug and added the Red Line MT-90. Hope Fumoto comes out with a valve drain plug for the Transmission by the time I do the next change. Filled the transmission till fluid started to drip out of the fill hole. Once the drips mostly subsided, I put the fill plug back in, torqued it to 27.3 ft lbs, cleared the area and dropped the BRZ off the stands.


Hopped in the car and took it for a drive. Outside temp was 51°F but the car was not very warm as the blue engine cold light in the dash was on. I took it slow for a while and shifting was really smooth in all gears. So much better than over the last week!


The real test will be the next few days with colder temps expected. Will post my results after the next few days.

Colour look nice.

Post an outside pic in the sun if you can.

I'm sick of all the white, grey, silver, red and blue cars.

It's nice to see something different for a change.

Opps, forgot topic

Recommend by "my guy" who is way smarter than me.

"Apparently" this brand with it's additives and stuff is GTG in relation to all the metal bits and is as smooth as silk, when warm.

Makes servicing the drive line simple with only 1 product to buy.

Opinions may vary.

GL-4 vs GL-5 Rated Fluids
 

When it comes down to it, we all will have different opinions as to which oils to use in our cars.


I've been going over posts and articles about transmission fluids for the past few weeks and am trying to get to a fact based solution to our 2nd-gear-crunch in cold weather issue. As of yet, and I am surprised that there hasn't been something done gear wise, there hasn't been a mechanical "FIX" to the 2nd gear crunch, like in the 2002-03 WRX "glass transmission." And not having the mechanical expertise to follow a gear swap myself, fluids are the priority, especially since the problem diminishes once the fluids heat up in the transmission.


Starting with some factual information:


The findings in the Rymax Lubricants website, which are reflected in many of the articles pertaining to GL-4 and GL-5:


There are four different classifications for transmission/gear oil. These different classifications define a certain level of performance in driven axles and manual gearboxes. They are mainly important for the transport sector in North America, Africa and Asia. The active classifications are:


• GL-1
• GL-4
• GL-5
• MT-1

The higher the Extreme Pressure (EP), the higher the GL category is. It is important to know that the SAE Motor Oil Viscosity Chart (J300) is different from the SAE Gear Oil Chart (J306). The viscosity has no relation with the API Gear Oil Classification and should be chosen based on the recommendations from the manufacturer based on the temperatures where you will drive.

The main difference between GL-4 and GL-5 gear oils is the amount of EP additives. Sulphur/Phosphorus containing products are used as EP-additive. This additive has the purpose to prevent the occurrence of micro-welds on the gear flanks at the local high temperatures which prevail in EP circumstances (temperatures well in excess of 800℃!) GL-5 has roughly twice the amount of EP additives compared to GL-4, which is why it is often used in high-pressure circumstances such as in a front axle and rear axle differential.
Sulphur/Phosphorus additives however have an unfavourable property: they can react aggressively towards bronze and copper. This can be disastrous for the synchromesh rings of a gearbox. Therefore it is not recommended to use GL-5 in a gearbox unless the manufacturer allows this.

To conclude:
• GL-4 is suitable for hypoid gear service when they are under severe service but are without shock loading.
• GL-5 is suitable for hypoid gear service under severe service and shock loads and not for use in a gearbox.

The Subaru BRZ transmission contains both copper and bronze synchronizer rings. So it is completely up to you to use a gear oil (GL-5 rated) that can damage these rings over time (leading to costly repairs). Which could also be part of the reason we have this issue to begin with (My local Subaru dealership put GL-5 in my transmission last week and made my issues worse).


If you are using a GL-5 product in your transmission and are having great results in eliminating the 2nd gear "crunch" in colder weather (seems anything sub 50°F), Awesome! Please let us know and do not spare the details.


But the fact that all your lubricant manufacturers warn that GL-5 oils should not be used in transmissions like ours, should weigh on your decision on what should be put in your transmission.


Sadly, doing a search of the 2nd gear "crunch" shows that this problem has been around since the 1st gen BRZ/FRS. So this tells me that there isn't a real solution to the 2nd gear "crunch" and we are just looking for a fluid solution that most alleviates this issue.


Again, I am no mechanic, so I don't know if there is a mechanical solution worth pursuing, like the gear swap on the 2002-03 WRX 5 speed manual "glass" transmission. The only reason I know about this, I had 2 '02 WRXs and was close to taking the 2nd one up to a place in Northern Virginia that would swap out the "bad gears with some German gears.


I guess when I get up tomorrow and find out if the recent transmission oil change has helped or not, will lead to me searching out the gear swap route. Or perhaps wait and see what's coming in a 2021 BRZ.


Thank you to everyone who has added pertinent info to this topic!

More pics...
 

Thank you! Happy to add more pics to my album shortly, instead of in this post. Thoroughly love my BRZ and definitely love the non-standard colors!
Series.Yellow was a limited run of 500 here in The States. There are a lot for sale at some really good prices.

I bought my 2016 FRS with 27,000 kl on the clock from a dealer off lease.
I assume it had the original fluids still in use.
I had no nasty shift issues although it isn't winter driven.
I planned to do lapping so changed the fluid to Motul 300.
Immediately I experienced the crunch when cold (spring start-up cold, not winter cold) going from 1st to 2nd. Once driven a few blocks the crunch was gone. No issues downshifting at any time or temp.
I will likely change out the fluids with Motul 300 again this summer unless something better comes to light.

Red Line MT-90 and the 2nd Gear Crunch...
 

Ok. I've had 2 days with Sub 40° F mornings to see how the Red Line MT-90 GL-4 Transmission oil would work in colder temps and the 2nd gear "crunch."

Each time, I started the car and let it sit for 5 minutes, letting the engine warm up (which, in case you do not realize, does not warm up the transmission oil) before starting to drive. Pulled down our road in 1st for about 100 yards before turning onto the major street. Pulled out and took 1st gear to 3K rpms and shifted to 2nd. I was immediately thrilled that I was not locked out of 2nd gear, like I had been with the Subaru GL-5 80W90.

There was a slight catch going in to 2nd, but not like it had previously been. On the first ride, I continued on and and as the transmission oil warmed, all shifts between gears leveled out and were nice and smooth. On the second ride, when I would shift from 1st to 2nd, I tried something different.

Clutch in, pull out of 1st and let the shifter go to neutral (if you let go of the shifter and let it sit in Neutral on it's own, it sits in the spot between 3rd and 4th gears), then pulled it back over and down into 2nd. This is all a fairly quick motion and it seems to eliminate the little "catch' I felt on the first day of cold driving. I had tried double clutching when I had the Subaru GL-5 in, and it helped, but still had the "crunch" and the lock out a couple times.

Seeing as numerous people have had similar results as mine by changing the transmission oil with pretty much every brand out there, but not totally eliminating the 2nd gear "crunch," my recommendations would be as follows.

If you have the 2nd gear "crunch":
• Change out your transmission oil (Highly recommend a GL-4 oil).
• Take it easy when you start driving and let the transmission oil warm up.
• When cold, Double Clutch going from 1st to 2nd (or try my suggestion for drifting into Neutral).


For those living in colder climates, it might be worth trying an oil pan heating element:
https://www.amazon.com/Kats-24150-Wa...2394558&sr=8-8

Be nice to get some input from anyone who is using one or willing to try one out. For $35, I may just get one to see if it makes any difference on the car. I'll report back if I go that route, but as we have relatively mild winters in the Mid-Atlantic of the USA, that money may go towards something more necessary - like a ceramic coating.

Once my BRZ was warmed up, I haven't had any issues with the transmission gears.

Hope this helps shed a little light on this and I do hope that you all enjoy your BRZs as much as I am!!

19° F this morning
 

A much colder 19° F to start this morning out. Did my 5 min engine warm up before driving off. Once I got over to the main road, did my little trick of shifting from 1st to Neutral and went smoothly into 2nd. Did that a couple more times before the transmission oil fully warmed up, but from then on it was smooth shifting.


Hope this helps so no one else has to really struggle thru this.

Just another data point:

I use Ford's newish Motorcraft XT-M5-QS GL-5 MTF. I basically use this on all my manual cars that call for GL-5 and it's excellent. I prefer it to the Redline products, because it works very well at low temperatures too. It definitely had a great impact on overall shift quality, but it is fairly expensive.

Another here running MT-90. No issues I'm liking it much more than the stock fluid