P0171, P219a after OFH2 install - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

phantasticity · 09-08-2016, 11:53 PM

I got those 2 codes p0172, p219a like 50 miles after installed openflash header v2, any ideas?

I'm on stg2 uel e85 btw.

jwvand02 · 09-09-2016, 01:03 PM

Did you use new gaskets?

Generally if you're getting this just from a header install it's either the header gaskets or the O2 sensor not being seated correctly.

steve99 · 09-10-2016, 07:55 PM

most likely you have exhaust leak

as previous guys said always use new gaskets

check the slip joint in header run some soapy water over it then start car when exhaust is cool.

check the 02 sensors in all the way and not leaking. run a thread tap through bungs in header if necessary

sensors installed in correct positions and plugged into correct coloured plugs.

you have high positive long term fuel trims , this is problem generally caused by exhaust leaks

09-08-2016, 11:53 PM	#1
phantasticity Ricer Join Date: Aug 2015 Drives: FR-S Location: NorCal Posts: 125 Thanks: 4 Thanked 14 Times in 12 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	P0171, P219a after OFH2 install I got those 2 codes p0172, p219a like 50 miles after installed openflash header v2, any ideas? I'm on stg2 uel e85 btw. Attached Images

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Chech Engine Light On P219A P119E P0171	tonytduc	Issues \| Warranty \| Recalls / TSB	4	09-21-2022 04:09 PM
NEW: OFH2, OFH3, v2.073 OTS maps and OFT350 E85 dyno results!	Shiv@Openflash	Engine, Exhaust, Transmission	67	12-10-2018 12:44 AM
CEL P219A?	SpeedR	Issues \| Warranty \| Recalls / TSB	38	05-24-2018 07:39 PM
P219A ENGINE CODE	Albaro08	Issues \| Warranty \| Recalls / TSB	6	12-29-2015 05:15 PM
P219A	TheseColorsDontRun	Issues \| Warranty \| Recalls / TSB	3	12-09-2013 05:08 AM

09-09-2016, 01:03 PM	#2
jwvand02 Senior Member Join Date: Apr 2014 Drives: 2013 SWP BRZ Limited Location: Louisville, KY Posts: 159 Thanks: 12 Thanked 47 Times in 34 Posts Mentioned: 2 Post(s) Tagged: 0 Thread(s)	Did you use new gaskets? Generally if you're getting this just from a header install it's either the header gaskets or the O2 sensor not being seated correctly.

09-10-2016, 07:55 PM	#3
steve99 Banned Join Date: Dec 2013 Drives: FT86 Location: Australia Posts: 7,996 Thanks: 1,035 Thanked 4,996 Times in 2,985 Posts Mentioned: 598 Post(s) Tagged: 2 Thread(s)	most likely you have exhaust leak as previous guys said always use new gaskets check the slip joint in header run some soapy water over it then start car when exhaust is cool. check the 02 sensors in all the way and not leaking. run a thread tap through bungs in header if necessary sensors installed in correct positions and plugged into correct coloured plugs. you have high positive long term fuel trims , this is problem generally caused by exhaust leaks

User Name		Remember Me?
Password