|
||||||
| Scion FR-S / Toyota 86 GT86 General Forum The place to start for the Scion FR-S / Toyota 86 | GT86 |
 |
|
|
Thread Tools | Search this Thread |
08-01-2012, 03:07 PM
|
#1 |
|
Enthusiast
Join Date: Jul 2012
Drives: Crystal Black BRZ Limited
Location: So Cal
Posts: 299
Thanks: 17
Thanked 71 Times in 49 Posts
Mentioned: 28 Post(s)
Tagged: 0 Thread(s)
|
Quad Exhaust Lip?
So I've been doing some looking around for a quad exhaust lip to install in place of the stock one that comes with the FR-S because I have been keeping up with a company that may be releasing one that I may be interested in purchasing.
Of course I have seen the TRD version which looks very nice but the thing I am worried about is: that after looking at some photos it looks like it hangs a bit lower than the stock(Dual/all black lip) one and wont match up with the stock side skirts I dont have any interest in adding on an entire body kit. I'm not so much interested in that as I am putting on a quad exhaust, lip spolier, and wheels. Simple and clean for me is just fine. Does anyone know or have you seen in person how much the actual drop is in the rear and if it would be extremely noticeable? if it is, then i obviously wont go that route. Ive also seen some companies doing quad exhaust test vidoes and noticed they have simply cut out the stock lip by hand but that doesn't look clean. Could the plastic be cut and molded for a clean lip by a company? thanks for any input. Last edited by Neekowahhhh; 08-01-2012 at 03:08 PM. Reason: bold questions |
|
|
|
12-17-2012, 07:44 AM
|
#2 |
|
Member
Join Date: Oct 2012
Drives: Kia Koup
Location: Australia
Posts: 39
Thanks: 9
Thanked 3 Times in 2 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Bump...asking the same question
|
|
|
|
|
12-17-2012, 02:29 PM
|
#3 |
|
Senior Member
Join Date: Aug 2012
Drives: WRB BRZ
Location: Westchester, NY
Posts: 539
Thanks: 26
Thanked 168 Times in 131 Posts
Mentioned: 9 Post(s)
Tagged: 0 Thread(s)
|
Look into the TRD bumper trim for the quad tip. Not the actually piece that goes along the whole bottom of the bumper, but rather two separate pieces that you mount to finish off the sections that would be cut. I just got my set from UPS today.
__________________
In the garage:
1988 BMW E30 M3 2003 Ducati ST4s ABS 2006 Subaru Legacy GT Spec B #444/500 (For Sale) 2013 Subaru BRZ WRB Limited - Acquired 9/15/12 |
|
|
|
|
12-17-2012, 02:45 PM
|
#4 |
|
Senior Member
Join Date: Nov 2011
Drives: 2013 SWP BRZ
Location: NoVA
Posts: 532
Thanks: 241
Thanked 142 Times in 97 Posts
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
|
Do you have a pic of the quad exhaust lip?
|
|
|
|
|
|
|
|
|
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Quad exhaust tips? | migle | Engine, Exhaust, Transmission | 86 | 09-23-2020 11:45 PM |
| Exhaust System/Exhaust Manifold Removal and Replacement | GrimmSpeed | DIY (Do-It-Yourself) Guides | 52 | 11-11-2015 09:30 PM |
| Stacked Quad Exhaust | quik1987 | Engine, Exhaust, Transmission | 43 | 08-16-2012 03:34 PM |
| Catback Exhaust vs Axleback Exhaust – What’s the difference? | phenom86 | Engine, Exhaust, Transmission | 10 | 07-28-2012 09:08 AM |
2013 Subaru BRZ Limited
