Engine Part Out - ***Updated 9/20/16***

[seant2h]

I was collecting parts to build a force fed, forged internal monster of a motor for my BRZ aaaaaand then my wife dangled the option to purchase another car in front of me. Now I'm going to leave my BRZ as is and sell off what I was collecting. I would like these parts gone asap so make me an offer if you are interested.

The parts are from at total of three motors which totals one full long block and second complete set of heads. One of the motors had a blown rod at just over 4000 miles and the second was from a crashed car which had 24,000 miles and the impact cracked the timing cover then I purchased a timing cover and other parts from the third motor.


For sale:

Drivers side / left cylinder head with entire valve train, camshafts, and cam carriers, no vvt sprockets: $200 shipped to you
Timing cover with center piece #2: $125 plus shipping
Crankshaft $100 plus shipping
High pressure fuel pumps (4k mi and 14k mi): $50 shipped
Passenger side Intake and Exhaust camshafts: $75 each plus shipping
Left side valve covers I have two at $20 each shipped
Left side VVT sprockets on the end of the camshafts: $50 each shipped
4 Spark plugs with 0 miles (installed and removed before starting car so crush washers are crushed): $40 shipped
2 Water pumps (4k mi & 24k miles): $25 each shipped
Belt Tensioner: $30 shipped
Engine wiring harness with a few burned connectors $50 shipped
Thottle body $60 shipped
Intake Manifold $50 plus shipping
Injector rails - $15 shipped
Injector ECU $50 shipped
Starter $50 shipped
Coolant crossover pipe: $10 plus shipping
Oxygen Sensors best offer
Both (2) OEM motor mounts: $40 shipped
OEM rubber intake pipe: $20 shipped
Various sensors:Best Offer
Thermostat:Best Offer
3 DI injectors (4th is presumed to be bad):Best Offer
Stock pulleys:Best Offer
2 sets of Cam Chain guides and tensioners (4k mi & 24k mi): Best Offer

SOLD:
Shortblock with 24k miles on it: $OLD
Complete left and right cylinder head set including vvt sprockets: $OLD
Camshaft vvt solenoids: 3 @ $OLD
Flywheel: $OLD
Transmission: $OLD
Perrin big MAF intake $OLD
Passenger side / right cylinder head with entire valve train and cam carriers, no vvt sprockets, no camshafts: $OLD
Timing cover with center piece #1: $OLD
4 Spark plugs with 4k miles: $OLD
Depot Racing catted midpipe $OLD
2 Cam Chains w/ Cam chain crank sprocket: $OLD
4 port injectors $OLD
Oil pan $OLD

[seant2h]

All pm's replied to. I'm trying to move this stuff so make an offer because no reasonable offer will be refused!

[aristo]

What(why is) makes the Perrin OP bent?

[seant2h]

Originally Posted by aristo

What(why is) makes the Perrin OP bent?

One of the parts motors that I purchased was in a front end collision which bent the overpipe. The OP should be considered a good piece to weld to since the flanges are high quality but it can not be used as is. Any offer will not be refused as long as I don't lose money in the deal.

[seant2h]

BUMP for an updated and organized list of parts with new pricing

[seant2h]

I have uploaded a video of the short block spinning.
[ame]http://youtu.be/PSgSp47BaSs[/ame]

[186]

DI injectors still available ?

[seant2h]

All messages replied to... I'm trying to move this stuff and I'm giving some great deals! PM me any offers because there are no low ball offers to me!

[ORGANIZED-CHAOS]

PM sent

[seant2h]

PM Replied, thanks for your interest

Originally Posted by ORGANIZED-CHAOS

PM sent

[ORGANIZED-CHAOS]

BUMP for a great seller!!! He is literally giving stuff away. He is not joking he really wants these parts gone!! Thanks Sean for the great deal!

[COO86L]

It's times like these I wish I lived in America :'(

[FX86]

Originally Posted by COO86L

It's times like these I wish I lived in America :'(

it's not all it's cracked up to be

[COO86L]

Originally Posted by FX86

it's not all it's cracked up to be

But cheap car parts. I wish I could buy a shortblock in Australia for 600 bucks. I'd have be a build engine straight away!
Shipping would be horrendous.