Spal Fan Shroud & Koyo Radiator - Page 3 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

MMorganFRS · 01-24-2014, 06:57 PM

@Carolina_Dyno No I haven't but just by looking it would give me room for FI on the LSX engine where it would have been tight before. I am still aquring parts at this moment

You are in my State and not that far so this is for sure on my got to buy list now

If i could get someone to buy my FA20 engine and transmission and help put in engine & trans, i would have enough to do the swap in the next month or so. I already have the engine just needing a few things to complete the swap plus mods for LS engine

OICU812 · 01-24-2014, 07:44 PM

This all looks to be fantastic

CSG Mike · 01-25-2014, 01:03 AM

Quote:

Originally Posted by Carolina Dyno

Sorry about that, I could have thrown some in if I knew you needed it. Glad to hear it fits well, was the seal properly pressed up against the core? There isn't much wiggle room with the seal we had to use.

Oh, it's our fault that we were in such a rush

xjohnx · 01-25-2014, 10:27 AM

Quote:

Originally Posted by CSG Mike

Oh, it's our fault that we were in such a rush

was the seal pressed properly against the core?

nelsmar · 01-27-2014, 01:39 PM

So how much will this be without fans?

CSG Mike · 01-27-2014, 02:17 PM

Quote:

Originally Posted by xjohnx

was the seal pressed properly against the core?

@Evasive Motorsports did the install; this actually is currently on @ImperiousRex's turbocharged car. I did, however, see pictures, and it is sealed all around to the radiator.

We used a SPAL 12" slim and 12" medium fan. The fatty fan (that I would prefer to use myself) did not fit due to the Greddy turbo kit. I believe it will fit without issue on a non-turbocharged car; fitment is TBD on other FI solutions.

This is a quality piece, and I don't often say that

@Carolina Dyno: Ben, I suspect we'll be ordering a few more of these in the future...

Carolina Dyno · 01-27-2014, 07:41 PM

Quote:

Originally Posted by nelsmar

So how much will this be without fans?

We will be selling these with no fans or hardware (just the finished shroud and rubber seal) for $175 plus shipping or $400 plus shipping complete.

Quote:

Originally Posted by CSG Mike

@Evasive Motorsports did the install; this actually is currently on @ImperiousRex's turbocharged car. I did, however, see pictures, and it is sealed all around to the radiator.

We used a SPAL 12" slim and 12" medium fan. The fatty fan (that I would prefer to use myself) did not fit due to the Greddy turbo kit. I believe it will fit without issue on a non-turbocharged car; fitment is TBD on other FI solutions.

This is a quality piece, and I don't often say that

@Carolina Dyno: Ben, I suspect we'll be ordering a few more of these in the future...

Great to hear it fits the robispec, we'll add it to the fitment list. Thanks for the good words.

Carolina Dyno · 01-28-2014, 09:59 PM

For anyone in a rush, we got a couple of these done tonight. They will be finished and have the fans mounted as they are ordered to allow for custom options. The website should be live on Wednesday but we can accept PayPal or CC by phone until then.

ImperiousRex · 01-28-2014, 10:11 PM

Quote:

Originally Posted by Carolina Dyno

For anyone in a rush, we got a couple of these done tonight. They will be finished and have the fans mounted as they are ordered to allow for custom options. The website should be live on Wednesday but we can accept PayPal or CC by phone until then.

Nice work! I'm expecting to get my car back from @Evasive Motorsports in a couple days and when I stopped by last week to check out the fitment, everything looked good. Dennis at Evasive did mention they needed to trim a little around the side hosing for the radiator as well as provide the nuts and bolts to get everything fastened on but it wasn't anything major. Can't wait to test out the new fans and shroud at the track next weekend and thanks so much for accomodating me via @CSG Mike

Carolina Dyno · 01-28-2014, 10:20 PM

Quote:

Originally Posted by ImperiousRex

Nice work! I'm expecting to get my car back from @Evasive Motorsports in a couple days and when I stopped by last week to check out the fitment, everything looked good. Dennis at Evasive did mention they needed to trim a little around the side hosing for the radiator as well as provide the nuts and bolts to get everything fastened on but it wasn't anything major. Can't wait to test out the new fans and shroud at the track next weekend and thanks so much for accomodating me via @CSG Mike

Good to know, I would love to know where they had to trim it so I can update the design to fit the Robispec without issue. I only have a Koyo, and stock radiator on hand.

I'm glad you're happy with the shroud, let us know how it goes on track.

Evasive Motorsports · 01-29-2014, 12:34 AM

Quote:

Originally Posted by ImperiousRex

Nice work! I'm expecting to get my car back from @Evasive Motorsports in a couple days and when I stopped by last week to check out the fitment, everything looked good. Dennis at Evasive did mention they needed to trim a little around the side hosing for the radiator as well as provide the nuts and bolts to get everything fastened on but it wasn't anything major. Can't wait to test out the new fans and shroud at the track next weekend and thanks so much for accomodating me via @CSG Mike

Should be soon Ted

Carolina Dyno · 01-30-2014, 06:29 PM

Our online store is now live at store.carolinadyno.com

One more pic while we're at it. We are pretty lucky with this platfrom to be able to perfectly fit these fans, notice how little space is left between the seals, it's almost all fan. We did everything we could to make sure there is no overlap around the edge of the fans, even between the two. The only place the aluminum protrudes into the fan surface is at the bolt holes and that's completely unavoidable.

Carolina Dyno · 03-18-2014, 04:21 PM

2 left from our first production run! We have plenty more on order.

sw20kosh · 05-21-2014, 07:24 PM

Any in stock?

01-24-2014, 06:57 PM	#29
MMorganFRS Member Join Date: Sep 2013 Drives: 2013 Scion FRS Location: Charlotte, NC Posts: 72 Thanks: 22 Thanked 8 Times in 8 Posts Mentioned: 5 Post(s) Tagged: 0 Thread(s)	@Carolina_Dyno No I haven't but just by looking it would give me room for FI on the LSX engine where it would have been tight before. I am still aquring parts at this moment You are in my State and not that far so this is for sure on my got to buy list now If i could get someone to buy my FA20 engine and transmission and help put in engine & trans, i would have enough to do the swap in the next month or so. I already have the engine just needing a few things to complete the swap plus mods for LS engine __________________ 2013 Scion FRS (Whiteout) 6-Speed Manual Zex Wet Nitrous Kit (Not Installed) www.morgansfrs.com "Nitrous is like a hot girl with and STD, you want to hit it but you are afraid of the consequences"

01-27-2014, 01:39 PM	#33
nelsmar Senior Member Join Date: Feb 2013 Drives: FR-S Location: Phoenix Posts: 2,605 Thanks: 733 Thanked 2,361 Times in 1,031 Posts Mentioned: 345 Post(s) Tagged: 3 Thread(s)	So how much will this be without fans? __________________ When I grow up, I wanna be God. My flickr - *Canibeat* Local magazine scout Old Setup: Vortech Supercharged 360WHP/262WTQ @ 11.5psi My build thread - WTF happened to nelsmar's car thread

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
new koyo radiator	autobrz	Engine, Exhaust, Bolt-Ons	1	12-25-2013 09:42 AM
Frs/brz koyo radiator	F-T	Engine, Exhaust, Bolt-Ons	16	12-02-2013 03:48 PM
Koyo Radiator SALE!!!	Powerhouse Racing	Engine, Exhaust, Bolt-Ons	1	10-07-2013 11:22 AM
KOYO Radiator In-Stock!!! Free Shipping!!!	Titanmotorsports	Engine, Exhaust, Bolt-Ons	24	07-09-2013 06:55 PM
Koyo Radiator vs Oil Cooler	Captain Snooze	Engine, Exhaust, Transmission	54	06-22-2013 12:18 AM

01-28-2014, 09:59 PM	#36
Carolina Dyno Senior Member Join Date: Nov 2013 Drives: 2013 Location: Wilmington NC Posts: 186 Thanks: 3 Thanked 220 Times in 79 Posts Mentioned: 8 Post(s) Tagged: 0 Thread(s)	For anyone in a rush, we got a couple of these done tonight. They will be finished and have the fans mounted as they are ordered to allow for custom options. The website should be live on Wednesday but we can accept PayPal or CC by phone until then.

01-30-2014, 06:29 PM	#40
Carolina Dyno Senior Member Join Date: Nov 2013 Drives: 2013 Location: Wilmington NC Posts: 186 Thanks: 3 Thanked 220 Times in 79 Posts Mentioned: 8 Post(s) Tagged: 0 Thread(s)	Our online store is now live at store.carolinadyno.com One more pic while we're at it. We are pretty lucky with this platfrom to be able to perfectly fit these fans, notice how little space is left between the seals, it's almost all fan. We did everything we could to make sure there is no overlap around the edge of the fans, even between the two. The only place the aluminum protrudes into the fan surface is at the bolt holes and that's completely unavoidable.

03-18-2014, 04:21 PM	#41
Carolina Dyno Senior Member Join Date: Nov 2013 Drives: 2013 Location: Wilmington NC Posts: 186 Thanks: 3 Thanked 220 Times in 79 Posts Mentioned: 8 Post(s) Tagged: 0 Thread(s)	2 left from our first production run! We have plenty more on order.

05-21-2014, 07:24 PM	#42
sw20kosh Senior Member Join Date: Jul 2012 Drives: 2013 Black FR-S Location: SF Posts: 3,030 Thanks: 881 Thanked 2,014 Times in 990 Posts Mentioned: 153 Post(s) Tagged: 1 Thread(s)	Any in stock?

User Name		Remember Me?
Password