Plastic Modeling

[Tcoat]

Originally Posted by Kaotic Lazagna

It is not clean. Was handling it for probably at least an hour to finish things up. A lot of that was dialing in ride height and camber on all four corners. I'll clean and re wax it and take better pics...eventually. lol

Oh. And still gotta put on the license plates. Lol. Also debating on if I should put on the windshield wipers or not

Beautiful!
There is not a hope I could pull that off unless it was in a scrap yard someplace.

[Tcoat]

I like my models as dirty little things!

Tarped and prop in place. Canopy and gunsight all that are left. Will get a final dirt and mud treatment when I do the base up.

[Ohio Enthusiast]

Just to nitpick - the prop blades are bent more sideways in the photo but yours are bent more backwards (and the one that is sideways is bent the wrong way). Looks like the prop rotated counter-clockwise when viewed from the cockpit, with the blades bending to the left.

Edit: they're also aren't pitched at the same angle of attack. Not final posing?

[Kaotic Lazagna]

Originally Posted by Tcoat

Beautiful!
There is not a hope I could pull that off unless it was in a scrap yard someplace.

Those take way more skills. I actually came across a build on IG of some sedan that was crashed into a tree. Made me think of you. hahaha

[Tcoat]

Originally Posted by Ohio Enthusiast

Just to nitpick - the prop blades are bent more sideways in the photo but yours are bent more backwards (and the one that is sideways is bent the wrong way). Looks like the prop rotated counter-clockwise when viewed from the cockpit, with the blades bending to the left.

Edit: they're also aren't pitched at the same angle of attack. Not final posing?

Three of the blades are pretty much bang on when viewed from the front.



You are however correct that the one on the left is bent backwards from where it should be. I didn't catch that until I had put it on. When I tried to fix it I was pushing the limit on how many times you can bend plastic and almost broke it so just decided to leave it alone.
The angle of attack is set by how the blades mount in the hubs so I had no control over that.

[Tcoat]

Originally Posted by Kaotic Lazagna

Those take way more skills. I actually came across a build on IG of some sedan that was crashed into a tree. Made me think of you. hahaha

Not really. I can hide a lot of errors with the kit or my assembly with a dirty wash and some paint chips. You don't have that luxury with the gloss finish.

[beltax90]

[Kaotic Lazagna]

Still haven't cleaned the Crown Athlete, but decided to bust this one out to look over and start.

Not very pleased with it, especially since it was a re release I had pre ordered for several months before it was released. Panel lines are extremely shallow. That's fixable. However, the Vertex rear bumper/lip goes over the molded OEM rear bumper. Problem is, there are molded in mud guards on it, so when you put the Vertex bumper over, there are very large gaps due to the mud guards and the curvature of the OEM bumper vs the straight line Vertex bumper. I'll have to use some Tamiya putty to fill in the those gaps.

I can't even cut out the OEM rear bumper as the chassis mounting points are on it, and the Vertex bumper doesn't have anything.

My excitement for this kit has really dropped unfortunately.

[Tcoat]

Originally Posted by Kaotic Lazagna

Still haven't cleaned the Crown Athlete, but decided to bust this one out to look over and start.

Not very pleased with it, especially since it was a re release I had pre ordered for several months before it was released. Panel lines are extremely shallow. That's fixable. However, the Vertex rear bumper/lip goes over the molded OEM rear bumper. Problem is, there are molded in mud guards on it, so when you put the Vertex bumper over, there are very large gaps due to the mud guards and the curvature of the OEM bumper vs the straight line Vertex bumper. I'll have to use some Tamiya putty to fill in the those gaps.

I can't even cut out the OEM rear bumper as the chassis mounting points are on it, and the Vertex bumper doesn't have anything.

My excitement for this kit has really dropped unfortunately.

Don't be discouraged. You can still make it work. The few car models I do are usually from moulds made in the 60 or early 70s and are often not much more than vaguely car shaped lumps and they can still come out OK.

[Kaotic Lazagna]

Originally Posted by Tcoat

Don't be discouraged. You can still make it work. The few car models I do are usually from moulds made in the 60 or early 70s and are often not much more than vaguely car shaped lumps and they can still come out OK.

Vaguely car shaped lumps! LOL

I was only discouraged because I was super hyped about it. Dunno why, but I've always really liked the JZX100 Chasers, so that didn't help with over hyping the kit.

[Ultramaroon]

What's a mould?

[Ultramaroon]

Hould me.

[Spuds]

Originally Posted by Ultramaroon

What's a mould?

Idk, but is sounds quite ould.

[Tcoat]

Originally Posted by Ultramaroon

What's a mould?

mould Share
Mould is the British spelling for "mold" — the stuff you find growing on old bread or the container you use to create your jello masterpieces.

Living mould is like “mildew,” it’s a type of fungus that grows on damp or decaying matter. Mould can also mean a “caste” used to shape a hardening liquid. In this sense mould can refer to both the container and the end product that comes out of the mould. In addition, mould is used as a verb to describe the process of making a mould. When you pour plaster into a mould to make a shape, you mould that shape.

Definitions of mould
noun the distinctive form in which a thing is made
synonyms:cast, mold, stamp
see more
noun a distinctive nature, character, or type
synonyms:mold
see more
noun container into which liquid is poured to create a given shape when it hardens
synonyms:cast, mold
see more
noun a dish or dessert that is formed in or on a mold
synonyms:mold
see more
noun sculpture produced by molding
synonyms:clay sculpture, modeling, mold, molding, moulding
see more
verb make something, usually for a specific function
synonyms:forge, form, mold, shape, work
process, work, work on
shape, form, or improve a material
see more
verb form in clay, wax, etc
synonyms:model, mold
see more
verb form by pouring (e.g., wax or hot metal) into a cast or mold
synonyms:cast, mold
see more
noun a fungus that produces a superficial growth on various kinds of damp or decaying organic matter
synonyms:mold
see more
noun the process of becoming mildewed
synonyms:mildew, mold
see more
noun loose soil rich in organic matter
synonyms:mold
see more