Saskatchewan Thread

[JPxM0Dz]

Got my new mats today!

UPDATE: You'll be hard pressed to find a nicer mat that offers such perfect fitment

Pics coming Soon! Weather Tech badges will be replaced with STi badges

[JPxM0Dz]

Change of plans on my powered sub! I was originally looking at the Kicker 11PES10C, but ended up going with the Rockford Fosgate P300-10 which also showed up today

Specs & dimensions on both powered subs are very close, however the Rockford is basically 10 pounds lighter and I wanted to keep weight down in the trunk

Finish on the P300-10 is very nice and fitment is pretty close to perfect. It just clears the rear deck and is slightly angled to fit the contour of the back of the rear seat and just fits behind my rear strut bar. Couldn't ask for better luck and no need to secure the sub now

I'll post actual pics when get time

[JPxM0Dz]

More goodies on the way!

[SkAsphalt]

Oh your build, always amazing! How much does that sub weigh? can I ask the cost? I would love to add a sub to my mix...I mean, the deck already has pre-outs! haha

[JPxM0Dz]

Originally Posted by SkAsphalt

Oh your build, always amazing! How much does that sub weigh? can I ask the cost? I would love to add a sub to my mix...I mean, the deck already has pre-outs! haha

If I remember correctly, it's around 26lbs, the kicker variant is around 36lbs which I felt was a little too much

Grabbed mine off ebay for around $200 to $220 shipped to my door and no brokerage

Everything is pretty much wired up, just waiting for a my fuse block to show up. The sub has a quick connect/disconnect for the power, ground and lead turn on, so very easy to disconnect everything if you needed the sub removed in a hurry

On a side note, I ran 4 gauge power from the battery to the rear. There's a grommit on the drivers side below the master cylinder. It has a rubber tube already in place, just cut the end off and run your wires through. I had to use an a blade to make the opening a little larger to allow for the 4 gauge and a couple 16gauge wires to pass through. I ran a couple extra wires through for future use if the need be

Removing panels on both sides of car is pretty straight forward, everything just pops off, just take your time when doing this. I needed to use both sides of the car for this, sub rca's, future rear camera rca and lead turn on all went down the passenger side and 4 gauge power went down the drivers side. The 4 gauge ground was connected and run to sub underneath rear deck.

[SkAsphalt]

Thanks JP! sounds exactly how I would run it too. I did the stereo wiring in my old mustang and corolla and this sounds way easier. I am excited for some extra boom down the road

[frs baby]

jp are u available this weekend

[JPxM0Dz]

Originally Posted by frs baby

jp are u available this weekend

Sorry man, with family all weekend for Fathers Day!

[SkAsphalt]

A little bit of wheel colour. I was going for bronze and it really looked that way before the clear..but now it is more like a polished copper.

Looks orange because of the lighting and inside parking garage, orange/yellow bulbs dont help haha

[frs baby]

sorry jp i meant the weekend of the 23rd also sk asphault rims look sick

[JPxM0Dz]

Originally Posted by SkAsphalt

A little bit of wheel colour. I was going for bronze and it really looked that way before the clear..but now it is more like a polished copper.

Looks orange because of the lighting and inside parking garage, orange/yellow bulbs dont help haha

Nice!

Originally Posted by frs baby

sorry jp i meant the weekend of the 23rd also sk asphault rims look sick

Let me get back to you, havn't looked that far ahead into the week as of yet

[JPxM0Dz]

Here are some updated pics of recently installed Rockford Fosgate sub, Cusco race pedal and Weather Tech mats...

[frs baby]

looks nice i ordered my lowering springs from tein the other day

[JPxM0Dz]

Time for some engine bling