|
Tracking / Autocross / HPDE / Drifting What these cars were built for! |
|
Thread Tools | Search this Thread |
09-05-2024, 09:47 AM | #57 |
Senior Member
Join Date: May 2011
Drives: '23 BRZ
Location: Providence, RI
Posts: 4,624
Thanks: 1,403
Thanked 3,947 Times in 2,062 Posts
Mentioned: 85 Post(s)
Tagged: 0 Thread(s)
|
Going from 15mm to 16mm rear bar (29% stiffer) isn't going to hurt anything and is just about the easiest/cheapest thing to do. Also not likely to help if the issue is really front bump travel and being on the outside bumpstop midcorner...
|
The Following User Says Thank You to ZDan For This Useful Post: | Spuds (09-05-2024) |
09-05-2024, 02:06 PM | #58 |
Member
Join Date: May 2023
Drives:
Posts: 71
Thanks: 14
Thanked 21 Times in 17 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Got it aligned and corner balanced. 7 out of 12 gallons. On RPF1 17x9 A052 245/40/17. Sent from my iPhone using Tapatalk |
The Following User Says Thank You to Tomyyyu For This Useful Post: | ZDan (09-05-2024) |
09-05-2024, 03:41 PM | #59 |
Senior Member
Join Date: May 2011
Drives: '23 BRZ
Location: Providence, RI
Posts: 4,624
Thanks: 1,403
Thanked 3,947 Times in 2,062 Posts
Mentioned: 85 Post(s)
Tagged: 0 Thread(s)
|
|
09-05-2024, 03:53 PM | #60 | |
Member
Join Date: May 2023
Drives:
Posts: 71
Thanks: 14
Thanked 21 Times in 17 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
I’m a CT person who drives two hours to and from Devens MA. Love that site too much. Tried others, but Devens had the most competitive talent and lovely site. Sent from my iPhone using Tapatalk |
|
The Following User Says Thank You to Tomyyyu For This Useful Post: | ZDan (09-06-2024) |
09-06-2024, 01:07 PM | #61 |
Member
Join Date: May 2023
Drives:
Posts: 71
Thanks: 14
Thanked 21 Times in 17 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
@ Went ahead and measured my center of wheel to fender and ended up with these heights. Are these too tall? Leading to too little droop travel?
RF - 14 2/16” RR - 14 6/16” LF - 14” LR - 14 8/16” Sent from my iPhone using Tapatalk |
09-06-2024, 02:37 PM | #62 | |
Quote:
- Andrew |
||
The Following User Says Thank You to Racecomp Engineering For This Useful Post: | Spuds (09-07-2024) |
09-06-2024, 02:43 PM | #63 | |
Member
Join Date: May 2023
Drives:
Posts: 71
Thanks: 14
Thanked 21 Times in 17 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Gotcha. So I got it corner balanced to follow my heights of 140mm front and around 145-155mm rear. That’s from floor to pinch weld. Wondering if it makes sense to just leave it as is for now, what would you recommend? Corner balanced weights attached. Since the rear was raised to get my cross weights correct. Sent from my iPhone using Tapatalk |
|
09-06-2024, 03:24 PM | #64 | |
Senior Member
Join Date: Aug 2020
Drives: 2017 BRZ PP, 2004 WRX
Location: Pittsburgh
Posts: 401
Thanks: 33
Thanked 302 Times in 185 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
Quote:
My height with issues (center hub to fender): Front 13 1/4" Rear 14 1/4" My height after lowering and allowing more droop travel (drives great now): Front 12 3/4" ("one finger gap") Rear 13 1/4" ("two finger gap") It sounds like you're literally 2" too high in the front and at least an 1" in the rear.
__________________
2017 BRZ Limited Performance Pack - Steel Cities Region SCCA / North Hills Sports Car Club
|
|
09-06-2024, 03:26 PM | #65 | |
Senior Member
Join Date: May 2011
Drives: '23 BRZ
Location: Providence, RI
Posts: 4,624
Thanks: 1,403
Thanked 3,947 Times in 2,062 Posts
Mentioned: 85 Post(s)
Tagged: 0 Thread(s)
|
Quote:
You might run it as it is and assess the handling situation, then lower all four corners about 12mm or 1/2" and see what that does to handling and balance, and go from there. |
|
09-06-2024, 03:27 PM | #66 | |
Member
Join Date: May 2023
Drives:
Posts: 71
Thanks: 14
Thanked 21 Times in 17 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Yeah, my plan is probably to run it as is. Then make adjustments. Since technically I still haven’t ran it yet. Sent from my iPhone using Tapatalk |
|
The Following User Says Thank You to Tomyyyu For This Useful Post: | ZDan (09-06-2024) |
09-06-2024, 03:27 PM | #67 | |
Member
Join Date: May 2023
Drives:
Posts: 71
Thanks: 14
Thanked 21 Times in 17 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
What is your setup? That will help paint a better picture. Sent from my iPhone using Tapatalk |
|
09-06-2024, 05:22 PM | #68 | |
Senior Member
Join Date: Aug 2020
Drives: 2017 BRZ PP, 2004 WRX
Location: Pittsburgh
Posts: 401
Thanks: 33
Thanked 302 Times in 185 Posts
Mentioned: 7 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Vorshlag vs RCE/KW camber plates won't make a huge difference in height between the two, comparing the two setups in terms of height should be very much the same.
__________________
2017 BRZ Limited Performance Pack - Steel Cities Region SCCA / North Hills Sports Car Club
|
|
09-06-2024, 05:40 PM | #69 | |
Member
Join Date: May 2023
Drives:
Posts: 71
Thanks: 14
Thanked 21 Times in 17 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Yeah comparing two different things. So I’ll just have to see how it works out, lol. Sent from my iPhone using Tapatalk |
|
09-07-2024, 02:55 AM | #70 |
-
Join Date: Nov 2012
Drives: '13 FRS - STX
Location: SF Bay Area
Posts: 10,378
Thanks: 13,771
Thanked 9,496 Times in 5,009 Posts
Mentioned: 94 Post(s)
Tagged: 3 Thread(s)
|
949’s ride height suggestions have a lot to do with their damper design droop/bump lengths, it shouldn’t be gospel, but I think it’s a great starting point.
@Spuds do you have the big oem tapered bolt in the upper hole of your strut? You have to use some level of camber bolt, even just the smaller oe bottom bolt to get past -4 degrees of camber even when the struts are slotted. |
The Following User Says Thank You to strat61caster For This Useful Post: | Spuds (09-07-2024) |
|
|
Thread Tools | Search this Thread |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Understeer on '22 BRZ | Fletch | Tracking / Autocross / HPDE / Drifting | 29 | 12-20-2022 09:09 PM |
oversteer and understeer | orc | BRZ Second-Gen (2022+) -- General Topics | 76 | 10-05-2021 03:08 PM |
Why does car understeer when going downhill? | hpde_addict | Tracking / Autocross / HPDE / Drifting | 20 | 01-15-2018 09:42 AM |
Understeer after new wheels | carsebuco | Wheels | Tires | Spacers | Hub -- Sponsored by The Tire Rack | 16 | 12-04-2017 05:49 PM |
understeer on 17 brz | alex.s | Suspension | Chassis | Brakes -- Sponsored by 949 Racing | 37 | 09-11-2017 04:05 AM |