|
Forced Induction Turbo, Supercharger, Methanol, Nitrous |
|
Thread Tools | Search this Thread |
04-25-2020, 09:52 PM | #1 |
Member
Join Date: May 2017
Drives: 2017 BRZ Limited PP
Location: SF Bay Area
Posts: 28
Thanks: 0
Thanked 37 Times in 12 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Edelbrock SC ECU Mounting Plate Issue
I am installing an Edelbrock SC into my 2017 Subaru BRZ PP and have an issue with the ECU Mounting Plate. Step #119 of the Installation Guide shows the old ECU just mounting back in place with no issue. However, the instructions are for a 2013-2016 model. My 2017 has the upgraded intake manifold, and the ECU mounting plate has two large tabs with rubber rings which connect to the old intake manifold. These are prohibiting the ECU mounting bracket from being mounted with the new SC intake runners in place. Ideas or suggestions? Are 2017+ owners just cutting the mounts off the ECU mounting plate to make clearance? Perhaps I am missing something
|
04-25-2020, 11:57 PM | #2 |
Senior Member
Join Date: Mar 2017
Drives: Q5 + BRZ + M796
Location: Santa Rosa, CA
Posts: 7,884
Thanks: 5,668
Thanked 5,805 Times in 3,299 Posts
Mentioned: 70 Post(s)
Tagged: 0 Thread(s)
|
It is hard to tell. Do the tabs slide off?
__________________
My Build | K24 Turbo Swap | *K24T BRZ SOLD*
|
04-26-2020, 05:06 AM | #3 |
Senior Member
Join Date: Jun 2013
Drives: RX-7 / BRZ
Location: USA
Posts: 2,343
Thanks: 1,026
Thanked 2,501 Times in 1,081 Posts
Mentioned: 27 Post(s)
Tagged: 0 Thread(s)
|
Slide the rubber grommet out. Afterwards use some pliers to bend the tabs up clearing the supercharger's runners. Far enough up they don't make contact.
__________________
//2013 World Rally Blue BRZ Limited FBM Turbo--gone
//2018 Crystal White Pearl BRZ Ts 2.2l Harrop Supercharged |
04-26-2020, 04:12 PM | #4 |
Senior Member
Join Date: Jun 2017
Drives: '17 BRZ Series Yellow Edelbrock SC
Location: Clarksville, KY
Posts: 100
Thanks: 18
Thanked 23 Times in 18 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
I have a 2017 yellow series, I didn't run into that issue. You sure your SC is seated correctly?
Did you already tighten the lower ECU bolt? |
The Following User Says Thank You to snowtaipan For This Useful Post: | Irace86.2.0 (04-26-2020) |
04-26-2020, 05:34 PM | #5 |
Senior Member
Join Date: Mar 2017
Drives: Q5 + BRZ + M796
Location: Santa Rosa, CA
Posts: 7,884
Thanks: 5,668
Thanked 5,805 Times in 3,299 Posts
Mentioned: 70 Post(s)
Tagged: 0 Thread(s)
|
If not that ^^^ ...Do you have aftermarket injectors or something blocking/lifting the cover?
__________________
My Build | K24 Turbo Swap | *K24T BRZ SOLD*
|
04-26-2020, 09:16 PM | #6 |
Member
Join Date: May 2017
Drives: 2017 BRZ Limited PP
Location: SF Bay Area
Posts: 28
Thanks: 0
Thanked 37 Times in 12 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
The problem was how the ECU was mounted to the bracket from the factory. Once I removed the ECU from the ECU mounting bracket, the bracket bolted right up with 1-2 mm of clearance to the intake runners without modification. Then, I just bolted the ECU back onto the bracket using the 3 supplied screws.
Thank you for your assistance. The install continues. :-) |
The Following 2 Users Say Thank You to S0crates For This Useful Post: | CSG Mike (04-27-2020), Irace86.2.0 (04-27-2020) |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
License plate mounting | 333Matt | Cosmetic Modification (Interior/Exterior/Lighting) | 6 | 11-15-2016 07:29 PM |
Options for mounting BRZ license plate? | gt8613 | BRZ First-Gen (2012+) -- General Topics | 6 | 10-13-2014 02:12 PM |
*GROUP BUY* Rho-Plate License Plate Mounting Kit $40! | Massdrop | Groupbuys | 45 | 10-15-2013 07:07 PM |
rear license plate mounting bracket | fiveoneoh | Cosmetic Modification (Interior/Exterior/Lighting) | 10 | 03-24-2013 09:35 AM |
License plate mounting ideas? | csaba | Scion FR-S / Toyota 86 GT86 General Forum | 1 | 04-15-2012 09:58 PM |