follow ft86club on our blog, twitter or facebook.
FT86CLUB
Ft86Club
Delicious Tuning
Register Garage Members List Calendar Search Today's Posts Mark Forums Read

Go Back   Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB > Technical Topics > Issues | Warranty | Recalls / TSB

Issues | Warranty | Recalls / TSB Problems, issues, recalls, TSBs


User Tag List

Reply
 
Thread Tools Search this Thread
Old 08-19-2020, 06:02 PM   #1
wangmanlex
Junior Member
 
Join Date: Aug 2020
Drives: 2013 Subaru BRZ
Location: Silver Spring, Maryland
Posts: 4
Thanks: 0
Thanked 4 Times in 4 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Unhappy Installed New Clutch. P0011 Code Came On.

I’ve recently installed, with a help of few friends, a new ACT Clutch to my BRZ. We put everything back together and once we gave it a start the car started to idle very roughly jumping from 500 to even 2k rpms as if it was trying to stay alive. Shortly after it turned off as if it stalled. Friend turned it on again same issue and tried to go for a test drive. Car stalls every time it is put into neutral. Even while car is going downhill in neutral, same result. Later after the test driving the P0011 code shows up. We cleared it and tried again but same result. I’ve been digging around but still couldn’t find an issue related to my topic. I’m 80% sure the clutch install went right but as my experience for working on cars is little and is mostly leaned on another person my friends and I have no clue what happened. Any ideas? and please go easy on me
wangmanlex is offline   Reply With Quote
The Following User Says Thank You to wangmanlex For This Useful Post:
humfrz (08-19-2020)
Old 08-19-2020, 06:12 PM   #2
p1l0t
Senior Member
 
p1l0t's Avatar
 
Join Date: Jan 2016
Drives: 2016 Subaru BRZ Hyperblue
Location: West Hartford, CT
Posts: 8,416
Thanks: 22,575
Thanked 9,371 Times in 4,813 Posts
Mentioned: 58 Post(s)
Tagged: 1 Thread(s)
P0011 is the camshaft position sensor. Do you have a code reader? It should tell you which bank/sensor it is.

Sent from my SM-G975U using Tapatalk
p1l0t is offline   Reply With Quote
Old 08-19-2020, 06:24 PM   #3
e1_griego
Senior Member
 
e1_griego's Avatar
 
Join Date: Jul 2015
Drives: Many
Location: Independence, Ore.
Posts: 704
Thanks: 227
Thanked 391 Times in 235 Posts
Mentioned: 9 Post(s)
Tagged: 2 Thread(s)
Broke a driver's side cam sensor doing my clutch 3 months ago, just snapped the plug off the end of it.

Amazon had me a new one in two days.
e1_griego is offline   Reply With Quote
The Following 2 Users Say Thank You to e1_griego For This Useful Post:
jcw99 (08-22-2020), p1l0t (08-19-2020)
Old 08-19-2020, 08:07 PM   #4
wangmanlex
Junior Member
 
Join Date: Aug 2020
Drives: 2013 Subaru BRZ
Location: Silver Spring, Maryland
Posts: 4
Thanks: 0
Thanked 4 Times in 4 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
I didn’t catch it. Friend just cleared the codes and it hasn’t came back since.
wangmanlex is offline   Reply With Quote
The Following User Says Thank You to wangmanlex For This Useful Post:
humfrz (08-19-2020)
Old 08-19-2020, 08:16 PM   #5
humfrz
Senior Member
 
Join Date: May 2013
Drives: 2013 FR-S, white, MT
Location: Puyallup, WA
Posts: 29,861
Thanks: 28,777
Thanked 31,796 Times in 16,418 Posts
Mentioned: 707 Post(s)
Tagged: 2 Thread(s)
Quote:
Originally Posted by wangmanlex View Post
I’ve recently installed, with a help of few friends, a new ACT Clutch to my BRZ. We put everything back together and once we gave it a start the car started to idle very roughly jumping from 500 to even 2k rpms as if it was trying to stay alive. Shortly after it turned off as if it stalled. Friend turned it on again same issue and tried to go for a test drive. Car stalls every time it is put into neutral. Even while car is going downhill in neutral, same result. Later after the test driving the P0011 code shows up. We cleared it and tried again but same result. I’ve been digging around but still couldn’t find an issue related to my topic. I’m 80% sure the clutch install went right but as my experience for working on cars is little and is mostly leaned on another person my friends and I have no clue what happened. Any ideas? and please go easy on me
Was beer involved in this committee operation?

You only need to have two people helping you - one to hand you tools and the other to run and get more beer.

That way if you screw something up, you'll know who did it.

https://www.autoblog.com/2016/03/25/...shaft%20timing.

Good luck getting it sorted out. I'll guess you knocked a connection lose.
humfrz is offline   Reply With Quote
The Following User Says Thank You to humfrz For This Useful Post:
p1l0t (08-19-2020)
Old 08-22-2020, 10:21 PM   #6
wangmanlex
Junior Member
 
Join Date: Aug 2020
Drives: 2013 Subaru BRZ
Location: Silver Spring, Maryland
Posts: 4
Thanks: 0
Thanked 4 Times in 4 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by p1l0t View Post
P0011 is the camshaft position sensor. Do you have a code reader? It should tell you which bank/sensor it is.

Sent from my SM-G975U using Tapatalk
Engine light came back on but for some reason we're unable to read or even connect using the OBD Reader we have. I've checked ohms readings on the crankshaft sensor and two camshaft sensors on the driver side. They're all working properly.

I forgot to mention this but the traction control light is also on. I've read around the forums of these symptoms happening to many others but for this to happen after we install a clutch? It's painful to say. Friend suggests I buy an Open Flash Tablet which I'd rather not do or just call this issue to Subaru...

I've had another friend suggest the clutch itself could be the issue whereas its throwing off the crankshaft position sensor in some way. Other than that I'm still stumped...
wangmanlex is offline   Reply With Quote
The Following User Says Thank You to wangmanlex For This Useful Post:
humfrz (08-22-2020)
Old 08-22-2020, 11:14 PM   #7
humfrz
Senior Member
 
Join Date: May 2013
Drives: 2013 FR-S, white, MT
Location: Puyallup, WA
Posts: 29,861
Thanks: 28,777
Thanked 31,796 Times in 16,418 Posts
Mentioned: 707 Post(s)
Tagged: 2 Thread(s)
Quote:
Originally Posted by wangmanlex View Post
Engine light came back on but for some reason we're unable to read or even connect using the OBD Reader we have. I've checked ohms readings on the crankshaft sensor and two camshaft sensors on the driver side. They're all working properly.

I forgot to mention this but the traction control light is also on. I've read around the forums of these symptoms happening to many others but for this to happen after we install a clutch? It's painful to say. Friend suggests I buy an Open Flash Tablet which I'd rather not do or just call this issue to Subaru...

I've had another friend suggest the clutch itself could be the issue whereas its throwing off the crankshaft position sensor in some way. Other than that I'm still stumped...
I'd suggest you test your reader by hooking it up to another car. If it's bad, get a code reading with another reader.

Having the trouble code will be important in figuring out what is wrong.
humfrz is offline   Reply With Quote
Old 08-22-2020, 11:28 PM   #8
p1l0t
Senior Member
 
p1l0t's Avatar
 
Join Date: Jan 2016
Drives: 2016 Subaru BRZ Hyperblue
Location: West Hartford, CT
Posts: 8,416
Thanks: 22,575
Thanked 9,371 Times in 4,813 Posts
Mentioned: 58 Post(s)
Tagged: 1 Thread(s)
Yeah that code will tell you a lot. A good reader can also get the history of recent codes as well. Also there are 4 cam position sensors and the crank sensor. Sounds like you still have 2 more cam sensors to check?

Sent from my SM-G975U using Tapatalk
p1l0t is offline   Reply With Quote
The Following User Says Thank You to p1l0t For This Useful Post:
humfrz (08-23-2020)
Old 08-25-2020, 06:35 PM   #9
wangmanlex
Junior Member
 
Join Date: Aug 2020
Drives: 2013 Subaru BRZ
Location: Silver Spring, Maryland
Posts: 4
Thanks: 0
Thanked 4 Times in 4 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by humfrz View Post
I'd suggest you test your reader by hooking it up to another car. If it's bad, get a code reading with another reader.

Having the trouble code will be important in figuring out what is wrong.
I recently made a purchase of a reader my self and went to use it myself. Now after using the reader four codes have showed up....

P0102 - Mass or Volume Air Flow Circut Low Input
p0011 Intake Camshaft Position Timing- Over-Advanced (Bank 1)
p0021 Intake Camshaft Position Timing- Over-Advanced (Bank 2)
p0420 Catalyst System Efficiency Below Threshold (Bank 1)

So before I had scanned anything I took out the Crankshaft Position Sensor testing it for resistance and if it were still working. I decided to not put it back in and come back to it a later day. My friend decides to turn on my car in Accessory Mode, as the sensor is still not plugged in, to pump someone's tires as I have Air Suspension with a adapter to my tank. These codes were not there until the day of and was wondering what could've triggered this?
wangmanlex is offline   Reply With Quote
The Following User Says Thank You to wangmanlex For This Useful Post:
humfrz (08-25-2020)
Old 08-25-2020, 06:54 PM   #10
humfrz
Senior Member
 
Join Date: May 2013
Drives: 2013 FR-S, white, MT
Location: Puyallup, WA
Posts: 29,861
Thanks: 28,777
Thanked 31,796 Times in 16,418 Posts
Mentioned: 707 Post(s)
Tagged: 2 Thread(s)
Quote:
Originally Posted by wangmanlex View Post
I recently made a purchase of a reader my self and went to use it myself. Now after using the reader four codes have showed up....

P0102 - Mass or Volume Air Flow Circut Low Input
p0011 Intake Camshaft Position Timing- Over-Advanced (Bank 1)
p0021 Intake Camshaft Position Timing- Over-Advanced (Bank 2)
p0420 Catalyst System Efficiency Below Threshold (Bank 1)

So before I had scanned anything I took out the Crankshaft Position Sensor testing it for resistance and if it were still working. I decided to not put it back in and come back to it a later day. My friend decides to turn on my car in Accessory Mode, as the sensor is still not plugged in, to pump someone's tires as I have Air Suspension with a adapter to my tank. These codes were not there until the day of and was wondering what could've triggered this?
YIKES! Something(s) is/are messed up but it's waaaay over my pay grade to figure out what.

Hopefully someone will come along soon to help you out.
humfrz is offline   Reply With Quote
Old 08-25-2020, 11:53 PM   #11
solidsnake11
Senior Member
 
Join Date: Nov 2018
Drives: brz
Location: nc
Posts: 318
Thanks: 431
Thanked 739 Times in 443 Posts
Mentioned: 24 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by wangmanlex View Post

I've had another friend suggest the clutch itself could be the issue whereas its throwing off the crankshaft position sensor in some way. Other than that I'm still stumped...
Well your friend might be partially right. Did you align the crank reluctor up with the small dowel? It is behind the flywheel.

As far as going easy on you, my grandfather said if you've never messed anything up you have never done anything.

Last edited by solidsnake11; 08-27-2020 at 07:45 AM.
solidsnake11 is offline   Reply With Quote
The Following User Says Thank You to solidsnake11 For This Useful Post:
p1l0t (08-26-2020)
Old 08-26-2020, 06:24 PM   #12
p1l0t
Senior Member
 
p1l0t's Avatar
 
Join Date: Jan 2016
Drives: 2016 Subaru BRZ Hyperblue
Location: West Hartford, CT
Posts: 8,416
Thanks: 22,575
Thanked 9,371 Times in 4,813 Posts
Mentioned: 58 Post(s)
Tagged: 1 Thread(s)
I feel like with all those codes the MAF would likely be the cause because it might cause the others but the others would probably not cause it. SO I would check the wire going to the MAF and/or test/replace the MAF. (Put your cranksensor back in first though)

Sent from my SM-G975U using Tapatalk
p1l0t is offline   Reply With Quote
 
Reply

Tags
clutch, p0011, rough idle

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
P0011 & P0021 BlueLine Issues | Warranty | Recalls / TSB 14 09-17-2020 09:02 AM
P000A and P0011 Riftur Issues | Warranty | Recalls / TSB 5 02-13-2017 09:32 PM
P0455 EVAP Code after New Direct and Port Injectors Installed? (Vortech Supercharger) Figo Forced Induction 8 10-04-2016 01:40 PM
car won't start after clutch installed aquaman Issues | Warranty | Recalls / TSB 4 07-19-2016 01:29 AM
Need clutch installed - recommendations midnight23 Southern California 2 08-07-2013 09:37 PM


All times are GMT -4. The time now is 05:37 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
User Alert System provided by Advanced User Tagging v3.3.0 (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.

Garage vBulletin Plugins by Drive Thru Online, Inc.