|
Issues | Warranty | Recalls / TSB Problems, issues, recalls, TSBs |
|
Thread Tools | Search this Thread |
10-05-2021, 09:06 PM | #15 |
Senior Member
Join Date: Jun 2021
Drives: 2015 FR-S
Location: San francisco
Posts: 357
Thanks: 144
Thanked 154 Times in 101 Posts
Mentioned: 8 Post(s)
Tagged: 0 Thread(s)
|
cool, keep us posted on your cleaned injectors results!
|
10-27-2021, 01:01 PM | #16 |
Senior Member
Join Date: Nov 2017
Drives: Black FRS
Location: California
Posts: 146
Thanks: 3
Thanked 27 Times in 19 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
Bad news on the update. Cleaning the direct and port injectors did not fix the issue. Misfire on cylinder 2 on cold start but when start up sequence finishes, does not misfire. I haven't driven the car yet since it's at the shop but they said it drives fine once the start up sequence ends. Redline pulls in 3rd gear no misfire so they think it's the tune or maybe a sensor is bad.
Swapped coil packs around, new spark plug in cylinder 2, fuel pressure good, compression and leak down good, no carbon buildup on valves. Kinda wished I didn't fill with e85 to see if it cleared things before sending to shop. Need to drain or use up the fuel before switching to stock tune to see if its the tune. |
10-27-2021, 02:16 PM | #17 | |
Senior Member
Join Date: Jun 2016
Drives: 2016 BRZ
Location: NJ
Posts: 362
Thanks: 53
Thanked 160 Times in 105 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Quote:
|
|
10-27-2021, 03:10 PM | #18 |
Senior Member
Join Date: Nov 2017
Drives: Black FRS
Location: California
Posts: 146
Thanks: 3
Thanked 27 Times in 19 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
|
11-04-2021, 08:59 PM | #19 |
Senior Member
Join Date: Nov 2017
Drives: Black FRS
Location: California
Posts: 146
Thanks: 3
Thanked 27 Times in 19 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
If anyone wants to look at my logs it would be greatly appreciated. Had a few look at it on Facebook, but nothing on the logs pointed out to the problem. Just a very strange misfire. Kind of coming down to a electrical issue/ignition issue. Maybe bad sensor or a break in wire somewhere.
https://datazap.me/u/butterballz/mis...?log=0&data=31 https://datazap.me/u/butterballz/mis...?log=1&data=31 One log is during cold startup, this is where I get lots of misfires and hard misfire code in cylinder 2. Second log is driving it around after warming up, different load/rpm range, cruising to redline. No misfire except under certain repeatable scenarios. Basically giving it about 50% load around 3k rpm can make cylinder 4 misfire enough to soft code. |
11-06-2021, 07:26 PM | #20 |
義理チョコ
Join Date: Sep 2014
Drives: a 13 e8h frs
Location: vantucky, wa
Posts: 31,868
Thanks: 52,132
Thanked 36,520 Times in 18,921 Posts
Mentioned: 1106 Post(s)
Tagged: 9 Thread(s)
|
Something is wrong with #2 direct injector. As soon as it switches to 100% port injection, #2 misfire count goes to zero.
That is, as long as the correct cylinder is reported to be misfiring. ...but it's one of your direct injectors. edit: ...or the signal/power to that injector.
__________________
Last edited by Ultramaroon; 11-06-2021 at 10:34 PM. |
11-08-2021, 01:17 PM | #21 | |
Senior Member
Join Date: Nov 2017
Drives: Black FRS
Location: California
Posts: 146
Thanks: 3
Thanked 27 Times in 19 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Didn't get a chance to log during cold start after swap, but so far signs are good. |
|
11-08-2021, 03:29 PM | #22 | |
義理チョコ
Join Date: Sep 2014
Drives: a 13 e8h frs
Location: vantucky, wa
Posts: 31,868
Thanks: 52,132
Thanked 36,520 Times in 18,921 Posts
Mentioned: 1106 Post(s)
Tagged: 9 Thread(s)
|
Quote:
__________________
|
|
11-09-2021, 12:13 PM | #23 |
Senior Member
Join Date: Nov 2017
Drives: Black FRS
Location: California
Posts: 146
Thanks: 3
Thanked 27 Times in 19 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
|
The Following User Says Thank You to Butterballz For This Useful Post: | Ultramaroon (11-09-2021) |
11-09-2021, 12:25 PM | #24 | |
義理チョコ
Join Date: Sep 2014
Drives: a 13 e8h frs
Location: vantucky, wa
Posts: 31,868
Thanks: 52,132
Thanked 36,520 Times in 18,921 Posts
Mentioned: 1106 Post(s)
Tagged: 9 Thread(s)
|
Quote:
__________________
|
|
11-19-2021, 11:55 AM | #25 |
Persona Non Grata
Join Date: Nov 2015
Drives: '15 BRZ (WRB)
Location: On the Border
Posts: 1,882
Thanks: 2,016
Thanked 2,780 Times in 1,200 Posts
Mentioned: 10 Post(s)
Tagged: 1 Thread(s)
|
I dunno, maybe it's too many years dealing with 60s and 70's vintage motorcycles with weak ignition systems but misfires under load just scream SPARK in my ears. I had a couple of Honda single cam cb750s and once the plugs got a few miles on them they would develop a case of the blind staggers at anything over half throttle. I eventually reworked the ignition system from points to electronic triggers and upgraded the coils and never had another problem.
Edit: and I won't even mention Brit bikes. My Nortons were testimonials to Joe Lucas' title of "Prince of Darkness." I had a picture that was supposedly of him on my garage wall. The caption said "Be Home Before Dark." Oops I guess did mention them. The most damaging lies we tell are those we tell ourselves.
__________________
Slow is smooth, and smooth is fast
|
09-09-2022, 04:45 PM | #26 |
Senior Member
Join Date: Apr 2014
Drives: 84 CJ7, 08 Duramax, 2014 FRS
Location: Oregon
Posts: 478
Thanks: 338
Thanked 128 Times in 103 Posts
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
|
Looks like this one is resolved and long fixed, but I found a lot of interesting info in this thread on the same topic.
https://www.ft86club.com/forums/show...cts+quad+spark After reading through it all, especially with 13-14 models, it looks like the pins don't make robust contact and are party to the misfires. I have a mild misfire issue comparatively and plan on the pin tweak this weekend. I've only had two misfires recently, and I get them only when pulling to 7k, and intermittently as I haven't been able to repeat at will. So I'm not swapping parts yet to see if signal follows, just seeing if I can make it go away as one user in the other thread had good luck with. |
09-12-2022, 12:03 PM | #27 |
Senior Member
Join Date: Apr 2014
Drives: 84 CJ7, 08 Duramax, 2014 FRS
Location: Oregon
Posts: 478
Thanks: 338
Thanked 128 Times in 103 Posts
Mentioned: 13 Post(s)
Tagged: 0 Thread(s)
|
Pin tweak didn't help me, but it is simple enough if you have the proper pliers. I left mine turned about to the point it's just noticeable. Regular needle nose are too large to fit in the connector housing. Oddly, got a CEL at the same 7k conditions, but it didn't record the code as I showed none when I checked with my reader. I even checked twice.
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Logs - Misfire Cylinder #1 | Butterballz | Issues | Warranty | Recalls / TSB | 8 | 06-06-2021 11:47 AM |
P0300 Random cylinder misfire | Grady | Issues | Warranty | Recalls / TSB | 6 | 12-02-2020 11:52 AM |
HELP P0354 Cylinder 4 Misfire | isaiah990 | Issues | Warranty | Recalls / TSB | 17 | 12-28-2019 10:38 PM |
P0463, u0122, and P0301 Cylinder 1 misfire | Shark_Bait88 | Issues | Warranty | Recalls / TSB | 0 | 08-12-2019 06:34 PM |