|
Engine, Exhaust, Transmission Discuss the FR-S | 86 | BRZ engine, exhaust and drivetrain. |
|
Thread Tools | Search this Thread |
04-26-2016, 06:10 PM | #1 |
@anthonysestito
Join Date: Oct 2015
Drives: 2013 Sterling Silver Metallic BRZ
Location: Vaughan
Posts: 391
Thanks: 117
Thanked 111 Times in 86 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Pulley install help.. Video inside
Installed my Perrin light weight pulley this week and noticed something. The actual crank bolt looks like it's wobbling. I made damn sure everything went in straight, bolt went in straight no problems. But when it spins it's scaring me a little. There's no wobble at all in the pulley itself, just the bolt. Could it be that the bolt is just dirty/discoloured and I'm losing my mind. Or should I just play it safe and order a new one and drop it in? No issues so far and the car runs fine. But I get ultra worried about minute things like this. XD
Sent from my iPhone using Tapatalk
__________________
2013 BRZ LIMITED STERLING SILVER METALLIC
IG: @ANTHONYSESTITO |
04-26-2016, 06:11 PM | #2 |
@anthonysestito
Join Date: Oct 2015
Drives: 2013 Sterling Silver Metallic BRZ
Location: Vaughan
Posts: 391
Thanks: 117
Thanked 111 Times in 86 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Sent from my iPhone using Tapatalk
__________________
2013 BRZ LIMITED STERLING SILVER METALLIC
IG: @ANTHONYSESTITO |
04-27-2016, 07:22 PM | #3 |
Senior Member
Join Date: Apr 2016
Drives: UltraMFrS
Location: OC
Posts: 701
Thanks: 204
Thanked 135 Times in 100 Posts
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
|
Oh I've has this problem the first time. the pully isn't sitting flushed or not tightly screw in or it could maybe be the belts are out of place but not likely.
check them again. when screwing it back in pull hand brake all the way up and put into first gear or reverse. hope this helps!! |
04-27-2016, 07:51 PM | #4 | |
@anthonysestito
Join Date: Oct 2015
Drives: 2013 Sterling Silver Metallic BRZ
Location: Vaughan
Posts: 391
Thanks: 117
Thanked 111 Times in 86 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Real strange. Pulley sits flush, belt I triple checked and is %100 on. Bolt went in no problem, no force and its torqued to spec. No wobble in the pulley either. Honestly I may order up a new bolt regardless and just re-install it. But super strange.
__________________
2013 BRZ LIMITED STERLING SILVER METALLIC
IG: @ANTHONYSESTITO |
|
04-27-2016, 08:13 PM | #5 |
Senior Member
Join Date: Apr 2016
Drives: UltraMFrS
Location: OC
Posts: 701
Thanks: 204
Thanked 135 Times in 100 Posts
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
|
I thought mines was flush the first time too but tighten using a pully I borrow from my mechanic. than it was truly tight. because that bolt will move the whole belt. unless you use a pully.
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Revworks UEL headers (video inside) | The Racers Line | Engine, Exhaust, Bolt-Ons | 4 | 05-12-2014 11:19 PM |
Red inside door handle grips how to install? | 914_WHITE_FRS | Cosmetic Modification (Interior/Exterior/Lighting) | 13 | 03-24-2014 12:21 AM |
Broken down FRS-T! video inside | Silverdub | Forced Induction | 26 | 05-22-2013 02:21 AM |
Chirp (Video Inside) | StOpNG0x | Issues | Warranty | Recalls / TSB | 17 | 12-13-2012 09:06 AM |
Idle RPM dip.... video inside. | CSG Mike | Engine, Exhaust, Transmission | 24 | 08-17-2012 01:45 PM |