|
||||||
| Software Tuning Discuss all software tuning topics. |
 |
|
|
Thread Tools | Search this Thread |
04-27-2018, 07:56 PM
|
#1 |
|
Junior Member
Join Date: Dec 2013
Drives: 2014 Subaru BRZ
Location: Columbus
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
OFT-MAF scaling for K&N typhoon intake
Has anyone scaled their MAF for this intake? Tuning with OFT and fuel trims are a little off. If anyone has the scaling they used that would be awesome! I’m going to work on datalogging to get it right, but I’m a newbie so it’s going to take a while to tackle the learning curve.
Already using Steve99’s post as a guide, just trying to shortcut if someone else already did it. http://www.ft86club.com/forums/showthread.php?t=64790 Seems like it really only has an issue during idle 20%ltft.....I’ve had this intake on for years, only just started logging etc....is this an issue or am I just making fuss? I read somewhere that the MAF being so close to the throttle body causes turbulence issues Last edited by ryankay; 04-28-2018 at 03:23 AM. Reason: Linking to other post. Clarification. |
|
|
|
04-29-2018, 11:12 PM
|
#2 |
|
Member
Join Date: Dec 2015
Drives: BRZ
Location: Bentonville, AR
Posts: 46
Thanks: 5
Thanked 15 Times in 11 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
Your high idle LTFT sounds more like an intake or exhaust leak more than anything. Is the LTFT closer to ideal once you are in higher load cells?
You are starting in a good place with Steve99's MAF scaling guide. Wayno also has some summarized info on http://www.wayneroms.com/ in the fuel tuning section. |
|
|
|
|
04-30-2018, 02:36 AM
|
#3 |
|
Junior Member
Join Date: Dec 2013
Drives: 2014 Subaru BRZ
Location: Columbus
Posts: 4
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
Cruising, in town, aggressive WOT all decent ST/LT fuel trims. Generally within 5% rarely 10% letting off throttle in gear goes high trims similar to idle.
Haven’t noticed any Exhaust leaks Previously had an issue with leak on crankcase vent hose to intake (the fitting is npt to hose barb and it’s plastic) but not sure if that’s causing my issue or not :p After multiple logs, the MAF scale really isn’t off by much(if at all) to even bother with it for now. I’ll see if I can’t find a good aluminum replacement for that crankcase vent hose and try it out. |
|
|
|
|
04-30-2018, 07:01 AM
|
#4 |
|
Senior Member
Join Date: Aug 2016
Drives: 2012 GT86 EU-spec
Location: The Netherlands
Posts: 204
Thanks: 232
Thanked 149 Times in 99 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Overrun = same trims as idle, it corrects on idle and applies on overrun. However during overrun injectors shut of anyway so its purely cosmetic. Sounds like a maf scaling issue to me. Make a log with some third gear pulls and closed loop driving and share it with datazap.me. Trims only tell part of the story. How afr compares to commanded afr tells a lot too.
__________________
Last edited by Vin; 04-30-2018 at 07:20 AM. |
|
|
|
|
08-30-2021, 01:25 AM
|
#5 |
|
Junior Member
Join Date: Aug 2021
Drives: 2013 Scion FRS
Location: Kentucky
Posts: 6
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
I have the same intake and I get my LTFT's around -14 with STFT around .75 at idle, also getting some knock correction and flkc, I need some help with scaling this thing too
|
|
|
|
|
|
|
|
|
| Tags |
| intake, k&n, maf, oft, scale |
| Thread Tools | Search this Thread |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| K&N Typhoon Cold Air Intake | sh1nd0kun | Engine, Exhaust, Bolt-Ons | 5 | 09-15-2017 01:39 PM |
| K&N Typhoon 69 Air Intake | doctor_driver | Engine, Exhaust, Bolt-Ons | 1 | 02-22-2017 03:24 PM |
| FS K&N 69 Typhoon Air Intake | dejahboi | Engine, Exhaust, Bolt-Ons | 3 | 02-04-2017 03:37 PM |
| K&N Typhoon Intake | els7x5 | Engine, Exhaust, Bolt-Ons | 3 | 09-29-2016 11:29 PM |
| fs/ft: k&n typhoon intake | Hmongfrs | Engine, Exhaust, Bolt-Ons | 2 | 11-19-2014 07:10 PM |
