01-11-2016, 01:55 AM | #519 | |
Canada Eh!
Join Date: Nov 2013
Drives: '13 FRS
Location: Calgary, AB
Posts: 447
Thanks: 156
Thanked 230 Times in 120 Posts
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
|
Quote:
I had some Rona green painters tape laying around... I thought I did a decent job with the cutouts, but the tint "bled" through the lines in some spots... oh well... |
|
01-11-2016, 01:56 AM | #520 |
Canada Eh!
Join Date: Nov 2013
Drives: '13 FRS
Location: Calgary, AB
Posts: 447
Thanks: 156
Thanked 230 Times in 120 Posts
Mentioned: 3 Post(s)
Tagged: 0 Thread(s)
|
It came out ok... Not perfect, but idk I guess we can let the pictures speak for themselves.
I used 4-5 coats of Red Duplicolor Metalcast, and 2-3 coats of Duplicolor Acrylic Clear Coat. I also used some autobody grade wax and grease remover I had laying around from a previous project. However, I didn't bother to scuff up the housings... Others seem to have no problems, but I guess only time will tell... All taped up... Should have taken more time during this step. Oh well... Right. After a few light coats of Metalcast. 2-1 by joeag., on Flickr Left, also after a few light coats of Metalcast. 3-1 by joeag., on Flickr Couple coats of clear, and after drying. Color came out OK! Here's the left side 4-1 by joeag., on Flickr 5-1 by joeag., on Flickr 6-1 by joeag., on Flickr 7-1 by joeag., on Flickr Right Side 8-1 by joeag., on Flickr 9-1 by joeag., on Flickr Side by Side 10-1 by joeag., on Flickr 11-1 by joeag., on Flickr 12-1 by joeag., on Flickr 13-1 by joeag., on Flickr And sitting indoors to cure! (Garage is a little too cold up on this side of the border) 15-1 by joeag., on Flickr |
The Following User Says Thank You to Joe-G For This Useful Post: | brybot (03-20-2017) |
01-11-2016, 11:35 PM | #521 |
Senior Member
Join Date: Jan 2015
Drives: Asphalt 2013 FR-S
Location: Vancouver, BC
Posts: 253
Thanks: 38
Thanked 126 Times in 73 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Redid mine last night as they had faded over the last summer. Decided that I was going to do it heavy and proper this time so I used a whole can of VHT nightshade red, and then an entire can of Spraymax 2k (which is by far the most vile stuff I have ever come across, even with a proper respirator on) Turned out great. Bit of orange peel but that sanded and buffed right out.
|
01-12-2016, 05:35 AM | #522 |
POWER!!!!!!!!!!!!!!!!!!!!
Join Date: Oct 2015
Drives: White Toyota 86 (Scion FRs)
Location: South Africa
Posts: 729
Thanks: 613
Thanked 259 Times in 192 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
Most of these "spray jobs" look much better than I thought they would... cool!!
I am a sh!t handyman, so bought Valenti's myself (and I love the shape of the lights - especially at night). But had I known about this first I probably would've gone this route!
__________________
I like driving!
|
01-12-2016, 04:10 PM | #523 |
Senior Member
Join Date: Apr 2014
Drives: 2013 Ultramarine Scion FRS MT
Location: Maryland
Posts: 164
Thanks: 38
Thanked 78 Times in 46 Posts
Mentioned: 2 Post(s)
Tagged: 2 Thread(s)
|
@joeag: Look great! I'm tackling this soon. I want to go with the same cutouts as you since my reverse lights are where the stock signal lights are. (Diode Dynamics Tail as turn module). I'll let you know how mine turns out.
__________________
|
01-13-2016, 10:09 AM | #524 |
Senior Member
Join Date: Jul 2014
Drives: 14 BSP Edelbrock BRZ
Location: Lon Gisland
Posts: 806
Thanks: 113
Thanked 450 Times in 256 Posts
Mentioned: 12 Post(s)
Tagged: 0 Thread(s)
|
If you are going to mask off a section to keep it clear the best way I have found is to pick up a roll of pinstriping tape. Gives a perfect edge and then you can overlap with the painter's tape a little off that edge.
|
01-13-2016, 11:44 AM | #525 |
Senior Member
Join Date: Jan 2013
Drives: scion fr-s
Location: montreal
Posts: 217
Thanks: 89
Thanked 148 Times in 77 Posts
Mentioned: 4 Post(s)
Tagged: 1 Thread(s)
|
Little question guys.. How much time need to wait before applied clearcoat on red metalcast? And 1can of metalcast and 1 can of spraymax clear coat enough for this project? Thanks for the help
Last edited by stevemp5; 01-13-2016 at 11:54 AM. |
01-13-2016, 12:32 PM | #526 |
Senior Member
Join Date: Jan 2015
Drives: Asphalt 2013 FR-S
Location: Vancouver, BC
Posts: 253
Thanks: 38
Thanked 126 Times in 73 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
1 can of each is perfect (use it all) Id wait about 30 minutes between the last coat of base and the clear.
|
The Following User Says Thank You to BDotG For This Useful Post: | stevemp5 (01-13-2016) |
01-13-2016, 02:06 PM | #527 |
Senior Member
Join Date: Jan 2013
Drives: scion fr-s
Location: montreal
Posts: 217
Thanks: 89
Thanked 148 Times in 77 Posts
Mentioned: 4 Post(s)
Tagged: 1 Thread(s)
|
OK cool man! Thanks for your help
|
01-18-2016, 11:05 AM | #528 |
Senior Member
Join Date: Apr 2014
Drives: 2013 Ultramarine Scion FRS MT
Location: Maryland
Posts: 164
Thanks: 38
Thanked 78 Times in 46 Posts
Mentioned: 2 Post(s)
Tagged: 2 Thread(s)
|
I used Frogtape - Delicate surface to mask off my area and got really clean lines. I'll share my entire process once I take more pictures after the clear dries. Just a thought, but I think using electrical tape would give you really smooth and crisp lines.
This is post redding, and pre-clear
__________________
Last edited by eggncheese; 01-18-2016 at 11:10 AM. Reason: grammar |
The Following User Says Thank You to eggncheese For This Useful Post: | axelo (01-21-2016) |
01-20-2016, 12:24 AM | #529 |
Senior Member
Join Date: Aug 2012
Drives: 1997 Acura NSX
Location: San Diego
Posts: 763
Thanks: 91
Thanked 174 Times in 118 Posts
Mentioned: 26 Post(s)
Tagged: 2 Thread(s)
|
nice .
B@t™ |
01-26-2016, 01:26 AM | #530 |
Senior Member
Join Date: Feb 2015
Drives: Toyota GT86
Location: Europe
Posts: 919
Thanks: 369
Thanked 554 Times in 301 Posts
Mentioned: 40 Post(s)
Tagged: 2 Thread(s)
|
Can I use any read spay paint to do this? Or does it have to be a transparent tinting color?
(Metalcast not available from Dupli Color in Europe as far as I can tell). |
01-26-2016, 10:10 AM | #531 |
Senior Member
Join Date: May 2013
Drives: 2013 BRZ
Location: Iowa
Posts: 928
Thanks: 135
Thanked 298 Times in 202 Posts
Mentioned: 1 Post(s)
Tagged: 0 Thread(s)
|
Definitely not, you need a transparent paint.
__________________
|
The Following User Says Thank You to qoncept For This Useful Post: | Tor (01-26-2016) |
01-26-2016, 07:04 PM | #532 |
Senior Member
Join Date: Feb 2015
Drives: Toyota GT86
Location: Europe
Posts: 919
Thanks: 369
Thanked 554 Times in 301 Posts
Mentioned: 40 Post(s)
Tagged: 2 Thread(s)
|
So Metalcast is a dedicated tinting paint?
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Are you going to smoke out your tail lights? | Liquidsnake | Cosmetic Modification (Interior/Exterior/Lighting) | 8 | 06-06-2012 09:02 AM |
HKS head and tail lamps | DIG1992 | Cosmetic Modification (Interior/Exterior/Lighting) | 5 | 05-19-2012 01:04 PM |
Tail of the Dragon | Tomcat9700 | Scion FR-S / Toyota 86 GT86 General Forum | 32 | 02-10-2012 02:30 PM |
Optional coloured tail lights? | m_life | Scion FR-S / Toyota 86 GT86 General Forum | 9 | 11-30-2011 06:20 PM |