Changing the door panel insert to blue.

[Master Jedi]

Here is the write up:
www.
gr86 . org
/threads/changing-the-insert-color.3088/page-3#post-60550

Removed the door panel per these instructions

Remove insert

Notice that all the screws are removed and I still have the pressed/melted fasteners For the melted tabs, drill out the center to 1/8inch depth and use a razor blade and cut under the insulation and shave it off so the black ring that is left by the drill and cut it and go by 14x1/2 or 1/4 in Phillips screws ( purple circles ) this will allow you to screw it back on like stock and is clean after.

Then remove the insert

Once the insert is removed wipe down with light soap and water and dry off

Then pull back the edge or the material with the backing only about 3-4 inch off and gradually and evenly apply the material to the insert.

Once the material is firmly in place turn over and cut excess off and remember to leave a little extra to wrap behind

Reinstall the insert, now with the holes you drilled take those 14 by 1/2 inch Phillips screws and screw in where you drilled out the metaled tabs.

once all the screws are back in re-install the door panel



Not hard and can be returned back to stock in 40 min.

[Rustyoid]

WOW that looks really good. I'd do the upper door panel and cluster bezel as well, ALL the alcantara!

[Spektyr]

Link is broken.

[RZNT4R]

Originally Posted by Rustyoid

WOW that looks really good. I'd do the upper door panel and cluster bezel as well, ALL the alcantara!

You dont want color on the cluster hood for visibility reasons. It reflects on the inside of the windshield and hampers vision, that's why dash flock exists.

[Tcoat]

Originally Posted by RZNT4R

You dont want color on the cluster hood for visibility reasons. It reflects on the inside of the windshield and hampers vision, that's why dash flock exists.

Beat me to it! I had a buddy do his dash in black and grey carbon fiber and as soon as the sun was bright it turned into an horrible checkerboard HUD on the windshield.

[MyHybridBurnsGasAndTires]

[dawsonj87]

Originally Posted by Spektyr

Link is broken.

The link is from *********. Tried linking to it myself and the same thing happens when you hit post. Where the **** is in the link, replace it with ********* and it should come up.

Alright then, this site is being a real pain. G R 8 6 . o r g.

[NoHaveMSG]

Originally Posted by Tcoat

Beat me to it! I had a buddy do his dash in black and grey carbon fiber and as soon as the sun was bright it turned into an horrible checkerboard HUD on the windshield.

One of my old shop guys was telling me years ago his dad sprayed clear on the dash of his sisters car to make it look better, he said it was impossible to drive in the summer


OP: Looks good, but.......

[Master Jedi]

Instructions and more pictures added

[VoltsFRS2013]

This looks pretty straightforward and honestly OEM+

I might have to find some material that closely matches what already comes on the door and knock it out.

[Spektyr]

Originally Posted by VoltsFRS2013

This looks pretty straightforward and honestly OEM+

I might have to find some material that closely matches what already comes on the door and knock it out.

OEM+ is exactly the kind of thing I like in mods. I'm kicking around the idea of doing this in black or dark blue on a Trueno GR86. Not completely sold on the idea, but it's growing on me (particularly since it's easy to undo and provides some protection to the original interior parts). If I end up doing it, I'll probably do some Dynamat while I have it apart.

My goal with any custom work on a car is to go for that "what if Toyota/etc. had offered a trim level above and beyond?" question. This is that. Not gaudy, not flashy, just an extra touch that fits the existing aesthetic.

[Master Jedi]

Right! I like the OEM+ look, I'm right there with you. " if Toyota had done this would it look like this"

[Master Jedi]

Originally Posted by VoltsFRS2013

This looks pretty straightforward and honestly OEM+

I might have to find some material that closely matches what already comes on the door and knock it out.

I wanted that as well, but I found that the fake leather rolls that had the adhesive backing wouldn't stretch to accommodate the bends needed to look clean. If you find some I might change it out. LOL

[Stephen02]

This is more subtle but it reminds me a lot of the colored interiors that Honda did with the S2k.