Random Thoughts - Part III The Search for Spark (No Politics) - Page 47 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

spike021 · 04-08-2022, 04:22 PM

Quote:

Originally Posted by NoHaveMSG

NGL the idea did pop into my mind earlier. I have a brand new roll of gorilla duct tape lol

Ultramaroon · 04-08-2022, 04:34 PM

Quote:

Originally Posted by spike021

I dropped a 10% full Brita filter pitcher from the counter to the kitchen floor and the cheap plastic chipped and now it leaks.

Anyone have an idea for a cheap fix?

Unless you like BPA leeching into your filtered water, replace it.

bcj · 04-08-2022, 04:43 PM

Flex Seal !!!!!

Looks like new Britta time.
May be able to find a used one at Salve Army or Goodwill.
Hot water wash cycle should see it through.

spike021 · 04-08-2022, 06:23 PM

It's actually kind of a bummer. I only bought this ~2 months ago, lol.

Ultramaroon · 04-08-2022, 07:09 PM

Quote:

Originally Posted by spike021

It's actually kind of a bummer. I only bought this ~2 months ago, lol.

I love BPA. My breasts are spectacular.

Tcoat · 04-08-2022, 07:21 PM

Quote:

Originally Posted by Ultramaroon

I love BPA. My breasts are spectacular.

Kiske · 04-08-2022, 07:36 PM

Got an offer for 36k for the tS today... engine swap to stock might be happening.

Edit. Also MY EYES!!!!

spike021 · 04-08-2022, 07:53 PM

Quote:

Originally Posted by Ultramaroon

I love BPA. My breasts are spectacular.

Aren't moobs the greatest? I love having built-in cushions when I lay down.

soundman98 · 04-08-2022, 08:18 PM

Quote:

Originally Posted by spike021

Aren't moobs the greatest? I love having built-in cushions when I lay down.

easier to play with your own too

Sapphireho · 04-08-2022, 08:38 PM

.

ichitaka05 · 04-08-2022, 09:41 PM

One of 3D printer I was looking into was on Amazon deal of the day, so pull the trigger & bought it. Kinda excited

soundman98 · 04-08-2022, 10:07 PM

Quote:

Originally Posted by ichitaka05

One of 3D printer I was looking into was on Amazon deal of the day, so pull the trigger & bought it. Kinda excited

i've decided to avoid 3d printers.

i keep staring at them at microcenter, and realized that the cost of the printer, and filament is entirely attainable.

but, i don't code very well. my eye's go blurry looking over all of it, and it takes me far too long for anyone else... and learning 3-d slicer programs, as well as any of the 3-modeling programs isn't all that far off from that either...

ichitaka05 · 04-08-2022, 10:11 PM

Quote:

Originally Posted by soundman98

i've decided to avoid 3d printers.

i keep staring at them at microcenter, and realized that the cost of the printer, and filament is entirely attainable.

but, i don't code very well. my eye's go blurry looking over all of it, and it takes me far too long for anyone else... and learning 3-d slicer programs, as well as any of the 3-modeling programs isn't all that far off from that either...

NohaveMSG showed me free online CAD program called tinkerCAD that’s very easy to use.

Plus there’s a thread in this forum for free 3D design. You can print those & don’t need to worry about designing one: https://www.ft86club.com/forums/showthread.php?t=123151

soundman98 · 04-08-2022, 10:23 PM

there's still bed alignment, speeds and feeds, temp control, water amount in filament, and downloaded file scaling issues...

04-08-2022, 07:36 PM	#651
Kiske Senior Member Join Date: Jun 2013 Drives: RX-7 / BRZ Location: USA Posts: 2,343 Thanks: 1,026 Thanked 2,501 Times in 1,081 Posts Mentioned: 27 Post(s) Tagged: 0 Thread(s)	Got an offer for 36k for the tS today... engine swap to stock might be happening. Edit. Also MY EYES!!!! __________________ //2013 World Rally Blue BRZ Limited FBM Turbo--gone //2018 Crystal White Pearl BRZ Ts 2.2l Harrop Supercharged

04-08-2022, 08:38 PM	#654
Sapphireho helmholtz resonator Join Date: Mar 2016 Drives: '15 ultramarine Location: Idaho Posts: 13,255 Thanks: 5,471 Thanked 18,330 Times in 8,654 Posts Mentioned: 156 Post(s) Tagged: 0 Thread(s)	. Attached Images

04-08-2022, 09:41 PM	#655
ichitaka05 Site Moderator Join Date: Oct 2009 Drives: ichi 86 Project Location: Middle of No where Posts: 20,974 Thanks: 7,672 Thanked 19,087 Times in 8,333 Posts Mentioned: 678 Post(s) Tagged: 27 Thread(s)	One of 3D printer I was looking into was on Amazon deal of the day, so pull the trigger & bought it. Kinda excited __________________

04-08-2022, 10:23 PM	#658
soundman98 ProCrastinationConsultant Join Date: Sep 2013 Drives: '14 Ranger, '18 Tacoma 4Dr LB Location: chicago-ish Posts: 11,330 Thanks: 35,240 Thanked 13,673 Times in 6,781 Posts Mentioned: 98 Post(s) Tagged: 0 Thread(s)	there's still bed alignment, speeds and feeds, temp control, water amount in filament, and downloaded file scaling issues... __________________ "The time you enjoy wasting is not wasted time"

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Random Thoughts - Part Deux [NO POLITICS]	Ultramaroon	Off-Topic Lounge [WARNING: NO POLITICS]	84004	03-07-2022 11:00 AM
OEM BRZ spark plug part number?	qqzj	Mechanical Maintenance (Oil, Fluids, Break-In, Servicing)	3	05-26-2017 11:33 PM
Random thoughts thread	MrVito	Off-Topic Lounge [WARNING: NO POLITICS]	37188	02-25-2016 10:00 AM
Random search on bing	sdwagonjp	Off-Topic Lounge [WARNING: NO POLITICS]	11	11-19-2014 07:35 PM

User Name		Remember Me?
Password