|
DIY (Do-It-Yourself) Guides For all DIYs. |
|
Thread Tools | Search this Thread |
09-24-2013, 04:02 PM | #1 |
Senior Member
Join Date: Apr 2013
Drives: 2013 Scion FR-S Boosted w/ JDL v2.1
Location: Ewa Beach, HI
Posts: 658
Thanks: 607
Thanked 211 Times in 156 Posts
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
|
DIY: Installing LED turn signal housing w/ DRLs
Hello everyone! Here's a quick and easy DIY on how to install your LED Turn signal housing with DRL bar.
Special thanks to: @Vicious LED for helping me out! Product info: Vicious LED Turn Signal Tools needed: 10mm Socket Socket Wrench Philips Screwdriver Flat Head Screwdriver Tap Wire Splice (2x) Electrical tape Wire cutter Oscillator cutter (Something to cut the plastic tab) Step 1: Remove the tabs of the plastic cover using a flat head gently until they pop out. Step 2: Turn your wheel inward to help ease the access of the 4 pop in locks of the plastic panel and remove the locks using a philips screwdriver. step 3: Use the 10mm socket to remove the 2 nuts holding the turn signal housing on to the bumper. Step 4: Cut the plastic tab that's pointing on the 2 O'clock position shown in the pic below. This will enable you to plug the harness to the new LED housing. Step 5: Use the wire tap splice to connect the YELLOW wire from the HOUSING to the GREEN wire of the HARNESS. Step 6: Use the wire tap splice to connect the GREEN wire from the HOUSING to the BLACK wire of the HARNESS. Note: Covered the RED and BLACK wires of the housing because if you have an LED relay, you wouldn't need it. Refer to the pic below Step 7: Make sure everything is connected properly and TEST to see if they are running. If DRLs are running but no turn signal, reverse the connection of the housing plug and the harness as you may have plugged it in wrong. Step 8 (optional): Wrap the splice connectors and the wire with electrical tape to ensure nothing goes wrong. Step 9: Put everything back and do the same thing on the other side. Enjoy your new LED housing with DRLs. End result: [ame="http://www.youtube.com/watch?v=s39AdpG4J1Q"]Turn Signal Housing for FRS - YouTube[/ame] Last edited by redsuns03; 09-24-2013 at 04:16 PM. |
The Following 2 Users Say Thank You to redsuns03 For This Useful Post: | illicitstylz (05-08-2014), MmmDieselFumes (10-21-2013) |
10-21-2013, 12:34 PM | #2 |
Senior Member
Join Date: Jul 2012
Drives: .
Location: .
Posts: 333
Thanks: 176
Thanked 118 Times in 80 Posts
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
|
I like that a lot, great write-up! Couple questions though:
1.) Are you running LED DRL's? 2.) The Turn Signal DRL's are essentially on all the time now, correct? Because I'm trying to figure out how to turn my existing DRLs "off" because they look dull and yellow (essentially I want them to only be High-Beams), and have these new Turn Signal DRLs be the only DRLs. If that makes sense. |
10-21-2013, 12:36 PM | #3 | |
Banned
Join Date: Feb 2013
Drives: 2013 Whiteout Scion FR-S 6MT
Location: Gainesville, FL
Posts: 3,272
Thanks: 1,278
Thanked 4,183 Times in 1,415 Posts
Mentioned: 28 Post(s)
Tagged: 2 Thread(s)
|
Quote:
|
|
The Following 2 Users Say Thank You to husker741 For This Useful Post: | MmmDieselFumes (10-21-2013), redsuns03 (10-21-2013) |
10-21-2013, 12:37 PM | #4 |
Senior Member
Join Date: Jul 2012
Drives: .
Location: .
Posts: 333
Thanks: 176
Thanked 118 Times in 80 Posts
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
|
|
10-21-2013, 12:41 PM | #5 |
Banned
Join Date: Feb 2013
Drives: 2013 Whiteout Scion FR-S 6MT
Location: Gainesville, FL
Posts: 3,272
Thanks: 1,278
Thanked 4,183 Times in 1,415 Posts
Mentioned: 28 Post(s)
Tagged: 2 Thread(s)
|
I'm not familiar with these lights but it should have no effect on them. It's a totally separate housing and function than your stock DRL. Your yellow DRL you see during the day also acts as your high beams at night. Once you turn your parking lights or low beams on, the DRL goes off. It will stay off until you turn all those lights back off, hence "Day-time running light." You could just change it to an LED bulb like many have, but you lose your high beams.
|
10-21-2013, 12:58 PM | #6 | |
Senior Member
Join Date: Apr 2013
Drives: 2013 Scion FR-S Boosted w/ JDL v2.1
Location: Ewa Beach, HI
Posts: 658
Thanks: 607
Thanked 211 Times in 156 Posts
Mentioned: 14 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Sent from the Underground Lair of Arizona 86 HQ |
|
04-18-2014, 06:44 PM | #7 |
Senior Member
Join Date: Sep 2012
Drives: Toyota GT 86
Location: Moscow, Russia
Posts: 460
Thanks: 409
Thanked 225 Times in 135 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
|
So, no need to resistors and stuff? Why then the recommended installation instructions are so complicated? How did you avoid hyperflashing?
|
05-07-2014, 11:33 PM | #8 |
Member
Join Date: Feb 2014
Drives: 13' AVO Whiteout
Location: Maryland
Posts: 93
Thanks: 3
Thanked 34 Times in 26 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
I would I also suggest these, because there is no wiring involved. And its a little bit cheaper.
[ame="https://www.youtube.com/watch?v=zMg2G8XFSBU"]White/Orange Switchback LED Turn Signals on Scion FR-S - YouTube[/ame] http://www.vleds.com/shop-bulb-numbe...hback-led.html |
The Following User Says Thank You to bryan767 For This Useful Post: | Nofiboy (12-07-2016) |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Full LED Front Bumper Triangular Parking & Turn Signal Light Housing Replacement | ZetaPerformance_CS | Cosmetic Modification (Interior/Exterior/Lighting) | 36 | 03-26-2014 12:18 AM |
Removing front signal housing, DIY? | wparsons | Cosmetic Modification (Interior/Exterior/Lighting) | 3 | 08-10-2013 04:43 PM |
WTB Stock FRS front turn signal housing | Yruyur | Interior Parts (Incl. Lighting) | 0 | 07-30-2013 12:09 AM |
LED Turn Signal Issue | FR-S Matt | Cosmetic Modification (Interior/Exterior/Lighting) | 15 | 07-23-2013 12:47 PM |
Anyone seen these turn signal/drl less? | djliquidsteele | Cosmetic Modification (Interior/Exterior/Lighting) | 7 | 07-15-2012 03:32 AM |