|
Forced Induction Turbo, Supercharger, Methanol, Nitrous |
|
Thread Tools | Search this Thread |
05-27-2014, 02:42 PM | #1 |
Senior Member
Join Date: Jan 2014
Drives: 2014 FRS
Location: Long Island NY
Posts: 117
Thanks: 43
Thanked 61 Times in 42 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
FRS AVO Automatic Trans Dyno
Posting to sharing my tuning results. @moto-mike set me up with a great tune and the car is sure to be a super smooth daily driver.
Automatic transmission with ~10 psi peak boost, 247HP / 218ft-lbs torque. Entirety of modifications: @AVOturboworld kit w/6psi wastegate spring. NXS manual boost controller. Stock overpipe(not a mod, I know). Tsudo highflow cat front pipe. Flowmaster cat back (discounted from ebay). Jegs 2.5 resonator (to take the rasp out of the flowmaster). [ame]http://youtu.be/jlMYUNiASpo[/ame] Last edited by onzippy; 05-27-2014 at 02:50 PM. Reason: Fix AVO mention |
The Following 4 Users Say Thank You to onzippy For This Useful Post: | Draco_PR23 (05-29-2014), paddleshifter (05-29-2014), protpibe (05-27-2014), Sportsguy83 (05-27-2014) |
05-27-2014, 03:42 PM | #2 |
NASA SpecE30 Racer
|
What was changed between run 002 and run 010? Nice low RPM torque pick up.
__________________
- King Tut
Street/Track Car: 2006 Honda S2000 TT3 || Race Car: 1987 BMW 325is SpecE30 || Tow Vehicle: 2014 RAM 1500 EcoDiesel Sold Cars: 2012 BMW M3 || 2013 Subaru BRZ || 2012 Porsche Cayman R || 2009 Chevrolet Z06 || 2009 BMW M3 || 2004 BMW M3 || 2004 Nissan 350Z |
The Following User Says Thank You to King Tut For This Useful Post: | onzippy (05-27-2014) |
05-27-2014, 03:59 PM | #3 | |
Senior Member
Join Date: Jan 2014
Drives: 2014 FRS
Location: Long Island NY
Posts: 117
Thanks: 43
Thanked 61 Times in 42 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
002 was the first run of the half finished e-tune from Mike that I drove in with. I couldn't always get new logs to Mike as fast as I wanted because of weather, traffic, work etc. and decided to drive to Moto-east and finish on the dyno. 010 is what I drove out with. Probably could have gotten there, or close, with e-tuning but I needed instant gratification.... so I can change more things.... and do it all over again. |
|
05-27-2014, 06:34 PM | #4 |
Join Date: Nov 2012
Drives: JDL Turbo FRS, 335SC BRZ (ret)
Location: Lehigh Valley, PA
Posts: 932
Thanks: 368
Thanked 1,547 Times in 525 Posts
Mentioned: 380 Post(s)
Tagged: 6 Thread(s)
|
Thanks for stopping by! Nice to finally drive a turbo AT after tuning a few! These automatics on the FT86 totally blew me away with how they hold the power without slip.
BTW as I'm sure it will get asked, the jaggy lines are simply a result of doing long AT pulls (3rd is too short, 4th is a bit long) with a lousy fan and heat soak. On the street with proper airflow the power will stay smoother. It was hitting 1.71 bar on spool and dropping off to 1.45 by redline. So about 10.5 dropping to 6 psi. Not bad for an AT on pump gas! |
05-27-2014, 07:47 PM | #5 |
Senior Member
Join Date: Oct 2013
Drives: 4-Runner Sport - 13' BRZ SportTech
Location: Winnipeg
Posts: 1,395
Thanks: 253
Thanked 839 Times in 459 Posts
Mentioned: 18 Post(s)
Tagged: 0 Thread(s)
|
Looks good !
I was actually surprised how decent the autos are in these cars. Not enough to make me get an auto, but still pretty awesome.
__________________
Top Tier Imports - Check out my build journal HERE
|
05-28-2014, 12:36 AM | #6 |
Senior Member
Join Date: Dec 2011
Drives: Moped
Location: CA
Posts: 4,298
Thanks: 4,897
Thanked 2,128 Times in 1,193 Posts
Mentioned: 21 Post(s)
Tagged: 0 Thread(s)
|
OP - Any plans to upgrade the trans or get a trans cooler?
|
05-28-2014, 06:16 AM | #7 |
Senior Member
Join Date: Jan 2014
Drives: 2014 FRS
Location: Long Island NY
Posts: 117
Thanks: 43
Thanked 61 Times in 42 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Not at the moment. There's a already an oil to water transmission fluid cooler/heat exchanger thing and I haven't seen water temps get much over 200 on the street. The weather is getting a lot warmer now so I'll keep an eye on water along with engine oil temps as we get into summer.
No plans for tracking it either. I'm thinking a standalone EBC to flatten out the boost and a sorting out of my hodgepodge exhaust are next on the to-do list. Thanks |
The Following User Says Thank You to onzippy For This Useful Post: | Lonewolf (05-28-2014) |
05-28-2014, 07:55 AM | #8 |
Senior Member
Join Date: Jan 2014
Drives: 2014 FRS
Location: Long Island NY
Posts: 117
Thanks: 43
Thanked 61 Times in 42 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
I just noticed I averaged 36.1 mpg on the 125 mile return trip. That's mostly 75-80 highway with a slight detour through the middle of Manhattan. I hate my gps sometimes.
|
The Following 2 Users Say Thank You to onzippy For This Useful Post: | Basket Case (05-28-2014), Okami (06-04-2014) |
05-28-2014, 08:44 PM | #9 |
Go Gators!
Join Date: Jun 2012
Drives: FRS White-out "blown up"
Location: Knox area, TN
Posts: 394
Thanks: 245
Thanked 111 Times in 79 Posts
Mentioned: 5 Post(s)
Tagged: 0 Thread(s)
|
Go automatics!!!!
__________________
"What do you mean I voided my warranty??"
FA20 Turbo + HRI Tune + FA20 Flex fuel + FA20club intake + SRT headerback exhaust + FA20 headers + KW3's + Hotchkis front and rear sway bars + Cusco strut tower bar + Perrin oil cooler + Perrin pulley & brake stop thingy + GFB water & alternator pulleys + Crawford air/oil separator |
The Following 3 Users Say Thank You to white devil For This Useful Post: |
05-28-2014, 08:54 PM | #10 |
Senior Member
Join Date: Nov 2011
Drives: Subaru BRZ Limited 6MT
Location: Winston-Salem, NC
Posts: 2,432
Thanks: 712
Thanked 954 Times in 545 Posts
Mentioned: 47 Post(s)
Tagged: 0 Thread(s)
|
Make sure to post to the dyno thread:
http://www.ft86club.com/forums/showthread.php?t=42290
__________________
Innovate Supercharged Black Limited BRZ 6-Speed MT(Build Thread)
2010 Cadillac CTS-V Sedan M6 w/550whp (Build Thread) |
05-29-2014, 08:07 AM | #11 | |
Senior Member
Join Date: Jan 2014
Drives: 2014 FRS
Location: Long Island NY
Posts: 117
Thanks: 43
Thanked 61 Times in 42 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Quote:
|
|
The Following User Says Thank You to onzippy For This Useful Post: | swift996 (05-29-2014) |
05-29-2014, 04:32 PM | #12 |
Senior Member
Join Date: Jan 2014
Drives: 2014 FRS
Location: Long Island NY
Posts: 117
Thanks: 43
Thanked 61 Times in 42 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Now that @swift996 pointed out that thread I feel a little underpowered.
Others with the AVO kit are posting much higher number on pump gas like mrfish and even Paul. http://www.ft86club.com/forums/showt...t=42290&page=3 What's up with that? Does the automatic really leach that much? |
05-29-2014, 04:40 PM | #13 | |
Senior Member
Join Date: Nov 2011
Drives: Subaru BRZ Limited 6MT
Location: Winston-Salem, NC
Posts: 2,432
Thanks: 712
Thanked 954 Times in 545 Posts
Mentioned: 47 Post(s)
Tagged: 0 Thread(s)
|
Quote:
__________________
Innovate Supercharged Black Limited BRZ 6-Speed MT(Build Thread)
2010 Cadillac CTS-V Sedan M6 w/550whp (Build Thread) |
|
05-29-2014, 05:57 PM | #14 |
Senior Member
Join Date: Jan 2014
Drives: 2014 FRS
Location: Long Island NY
Posts: 117
Thanks: 43
Thanked 61 Times in 42 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
I'm using the 6psi actuator and a MBC to get ~10 psi but Moto-mike said it was dropping to ~6 psi.
Is there a rule of thumb about spring pressure and and boost controllers? I mean, I've got an 8psi actuator from AVO also so is it better to install that and modulate the extra 2 psi with mbc to get the boost stable? And the driveability is awesome. No complaints there. |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Is there an Auto Trans only dyno thread? | Pure Automotive | Engine, Exhaust, Transmission | 17 | 07-17-2014 12:35 AM |
fs: Perrin trans mount and whiteline trans bushing | RWD_FR-S | Transmission and Driveline | 1 | 01-02-2014 05:34 PM |
Dyno numbers list from Evasive Motorsports Meet/Dyno | Fish | Southern California | 29 | 02-24-2013 03:16 AM |
Dyno Compilation - dyno testing results and recommendations | Illusive | Engine, Exhaust, Transmission | 82 | 02-08-2013 07:00 PM |
Base line dyno figure (dynapak Hub dyno) | gtauto | AUSTRALIA | 16 | 10-08-2012 08:06 AM |