Recaro Pole Position side mounts

[Ruben_86_]

Originally Posted by Mike_ZN6

@Ruben_86_ Were you able to install the driver/passenger Recaros and disable all the dash lights for the air bags, etc. ?

I have used a resistance in each connector and I have no light on the dash

[Ruben_86_]

Originally Posted by churchx

I wonder if such custom made side mount brackets:
1) don't net extra width due their shape like L, not 7, like in later schematic pics?
2) if they cannot be made adjustable for wider selection of seats .. by simply changing their bottom mount holes to longer slots?

Yes, they could be made adjustable for a little wider seats

[Mike_ZN6]

Originally Posted by Ruben_86_

I have used a resistance in each connector and I have no light on the dash

Even for the passenger seat? Did you transfer the occupancy sensor over to the passenger Recaro?


I tried to find you on instagram but didn't see any matches for @Ruben_86_

[Ruben_86_]

Originally Posted by Mike_ZN6

Even for the passenger seat? Did you transfer the occupancy sensor over to the passenger Recaro?


I tried to find you on instagram but didn't see any matches for @Ruben_86_

https://instagram.com/ruben_86_?igshid=ZDdkNTZiNTM=

I have not used the occupant sensor or the seat belt connectors, I do not know if I go with the passenger airbag always active.

but it doesn't mark me any problem in the dash

[gpvecchi]

The passenger airbag is always on. The seatbelt and occupant sensor is just for the seatbelt alarm.
Anyway, we're going offtopic.

[gpvecchi]

@Ruben_86_ can you please tell me what is the distance between the rear bolt in its lowest position and the floor?
I'd like to know if I can go lower using your brackets.

[Ruben_86_]

Originally Posted by gpvecchi

@Ruben_86_ can you please tell me what is the distance between the rear bolt in its lowest position and the floor?
I'd like to know if I can go lower using your brackets.

Hello, when I go to the garage I measure it, it will take a few days.I show you this photo that I have, the seat is very low, lower than the original





I already have the supports in production and orders are allowed on request

[Ruben_86_]

Originally Posted by gpvecchi

@Ruben_86_ can you please tell me what is the distance between the rear bolt in its lowest position and the floor?
I'd like to know if I can go lower using your brackets.

13-13,5cm

[gpvecchi]

Originally Posted by Ruben_86_

13-13,5cm

Thank you very much! I'll take precise measures of mine tomorrow!

[Ruben_86_]

Originally Posted by gpvecchi

Thank you very much! I'll take precise measures of mine tomorrow!

Put them here, I'm curious

[gpvecchi]

Took the measures: with Recaro JDM slider and Recaro JDM side brackets (not that stupid ABE ones), the height is between 13,5 and 14 cm. This is correct, as Recaro sliders are declared to be 5 mm higher from stock, probably because of the seat belt bracket.
I found a very low sliders from Japan, the Kawai Works, but they'll not permit to use the Recaro JDM side stands. But I got an idea from them, I'll try modding the Recaro sliders, perhaps I could get around 2,5 cm more lowering.

[Pat]

Why are ABE sliders stupid? I don't know much about this, and have a set waiting to go on as soon as my seat arrives.

[gpvecchi]

The ABE brackets are absurdly high. The seat will results higher than stock one. Using the JDM brackets I lowered it 2 cm.
I think the best and cheapest solution is to use the custom brackets sold by Ruben 86.

[Ruben_86_]

The height of my supports is limited by the shape of the original bar, but for me it is already low, more than the originals