Trunk Cancel Button Pressed, But Lock Seized - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

DjDATZ · 10-17-2021, 01:17 AM

Earlier this week, my trunk stopped opening from the cabin button and the remote. I've had this happen before, so I know I can just unlock the trunk from the lock above the license plate.

However, when I went to try that, it seems the lock has seized. I tried WD-40ing it to get it to release, but no dice. I tried rotating the key so hard that I apparently warped it so much, that I couldn't turn the ignition. (Simple solution to that, I just warped it back.)

Given that I don't want to destroy a key, what suggestions that I can try to get it to release? I could try reaching in to get to the straps behind the back seat to see if can pull on them to fold the seat down. Suggestions on how to do this?

Sent from my HD1905 using Tapatalk

villainous_frx · 10-17-2021, 01:27 AM

Shove your hands through the back seats and pull the rear seat release strap(s). Then get a 3D printed button cover and never worry about it again!

DjDATZ · 10-17-2021, 01:30 AM

Quote:

Originally Posted by villainous_frx

Shove your hands through the back seats and pull the rear seat release strap(s). Then get a 3D printed button cover and never worry about it again!

Tried that, my hand gets stuck at the wrist

Will ask the fiancée to try ahah

Will take a look for the button cover, duct tape will do temporarily!

Sent from my HD1905 using Tapatalk

villainous_frx · 10-17-2021, 03:39 AM

Quote:

Originally Posted by DjDATZ

Tried that, my hand gets stuck at the wrist

Will ask the fiancée to try ahah

Will take a look for the button cover, duct tape will do temporarily!

Sent from my HD1905 using Tapatalk

Using a piece of wire, such as a coat hanger has also worked for me in the past. Good luck!

DjDATZ · 10-17-2021, 06:30 PM

She couldn't get her hand in and I tried a bunch with a coat hanger and nada.

Sent from my HD1905 using Tapatalk

soundman98 · 10-17-2021, 06:51 PM

did you try pushing down on top of the trunk while trying to turn the key? sometimes it relieves enough pressure in the lock assembly to allow it to work.

RZNT4R · 10-17-2021, 07:36 PM

You're either going to have to get to the straps with some sort of hook, or take out the seat seat cushion, and move the rear side trim our of the way enough to remove the bolts holding the seatback hinge to go through from under.

But on an unrelated note, I was looking at your profile trying to see what year it was for the trunk cylinder to seize from corrosion, and while the year isn't listed, I see you're in toronto with a Kia Rondo...

... Get rid of that hot potato SOON. if you're in canada your cars are subject to rust and those kias have STRUCTURAL FUEL TANKS which are weak to rust, the start to leak from the bottom and cost several thousand dollars to replace.

villainous_frx · 10-17-2021, 08:10 PM

Quote:

Originally Posted by RZNT4R

trying to see what year it was for the trunk cylinder to seize from corrosion

2014 here and formerly winter driven, still need to take it apart and clean everything out of it

Dadhawk · 10-17-2021, 08:17 PM

You may be able to pull up the two "buttons" on the top of the back seat. Those are the latches. As I recall they basically work like door locks.

AJ32162 · 10-17-2021, 08:55 PM

This may help it's from a post by Stang70Fastback on another thread.

"Grab the black plastic trim surrounding the lock mechanism on the top corner of the rear seatback. Pull it up. It snaps right off. The pull up on the red-colored peg to release the seat. Then just snap the cover back on. It's that simple."

Dadhawk · 10-17-2021, 09:21 PM

Quote:

Originally Posted by AJ32162

This may help it's from a post by Stang70Fastback on another thread.

"Grab the black plastic trim surrounding the lock mechanism on the top corner of the rear seatback. Pull it up. It snaps right off. The pull up on the red-colored peg to release the seat. Then just snap the cover back on. It's that simple."

Yep, that's basically what I was saying, without the detail.

DjDATZ · 10-18-2021, 11:57 AM

Thanks for the tips y'all, will give them a try when I have a little time today!

Sent from my HD1905 using Tapatalk

DjDATZ · 10-18-2021, 11:59 AM

Quote:

Originally Posted by RZNT4R

But on an unrelated note, I was looking at your profile trying to see what year it was for the trunk cylinder to seize from corrosion, and while the year isn't listed, I see you're in toronto with a Kia Rondo...

... Get rid of that hot potato SOON. if you're in canada your cars are subject to rust and those kias have STRUCTURAL FUEL TANKS which are weak to rust, the start to leak from the bottom and cost several thousand dollars to replace.

Selina's a 2013 FR-S, got her August 2013!

The Rondo is on its way out, had a spate of a few weeks of going in and out of the mechanic's shop for various repairs. Third time replacing the water pump in about a year and a half.

IIRC it's a 2012 or 2011?

Sent from my HD1905 using Tapatalk

DjDATZ · 10-18-2021, 03:45 PM

Quote:

Originally Posted by AJ32162

This may help it's from a post by Stang70Fastback on another thread.

"Grab the black plastic trim surrounding the lock mechanism on the top corner of the rear seatback. Pull it up. It snaps right off. The pull up on the red-colored peg to release the seat. Then just snap the cover back on. It's that simple."

Worked like a charm, thank you! Now to find that button cover and get it ordered!

Sent from my HD1905 using Tapatalk

10-17-2021, 01:27 AM	#2
villainous_frx Off to the track! Join Date: Mar 2020 Drives: '14 Lava 86, '13 WRB BRZ Location: Canada Posts: 452 Thanks: 941 Thanked 704 Times in 289 Posts Mentioned: 11 Post(s) Tagged: 0 Thread(s)	Shove your hands through the back seats and pull the rear seat release strap(s). Then get a 3D printed button cover and never worry about it again! __________________ ZN6 Build \| Instagram

10-17-2021, 06:51 PM	#6
soundman98 elluctrik esktspurt Join Date: Sep 2013 Drives: '14 Ranger, '18 Tacoma 4Dr LB Location: chicago-ish Posts: 10,682 Thanks: 33,286 Thanked 12,873 Times in 6,399 Posts Mentioned: 92 Post(s) Tagged: 0 Thread(s)	did you try pushing down on top of the trunk while trying to turn the key? sometimes it relieves enough pressure in the lock assembly to allow it to work. __________________ "The time you enjoy wasting is not wasted time"

10-17-2021, 08:17 PM	#9
Dadhawk 1st86 Driver! Join Date: Feb 2012 Drives: '13 FR-S (#3 of 1st 86) Location: Powder Springs, GA Posts: 19,003 Thanks: 37,343 Thanked 23,613 Times in 10,794 Posts Mentioned: 177 Post(s) Tagged: 4 Thread(s)	You may be able to pull up the two "buttons" on the top of the back seat. Those are the latches. As I recall they basically work like door locks. __________________ Visit my Owner's Journal where I wax philosophic on all things FR-S Post your 86 or see others in front of a(n) (in)famous landmark. What fits in your 86? Show us the "Junk In Your Trunk".

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Seized motor/vapor lock after installing Edelbrock 1556	iceblaze	Forced Induction	26	12-28-2018 10:24 PM
Trunk button or fob trunk button aren't working.	kamilehaula	Issues \| Warranty \| Recalls / TSB	10	10-24-2018 07:33 AM
disable the trunk release cancel button	Riftur	Electronics \| Audio \| NAV \| Infotainment	19	02-13-2016 12:35 PM
Buzzing/popping sound when HID fog light button is pressed. HELP!	gabrielthethird	Cosmetic Modification (Interior/Exterior/Lighting)	3	02-08-2015 10:10 PM
when you hit the lock button on your key...	pr086	Scion FR-S / Toyota 86 GT86 General Forum	15	11-28-2012 12:55 AM

10-17-2021, 07:36 PM	#7
RZNT4R Professional Mechanic Join Date: Apr 2010 Drives: 2017 86 6MT Oceanic Location: Quebec, Canada Posts: 745 Thanks: 15 Thanked 565 Times in 340 Posts Mentioned: 12 Post(s) Tagged: 0 Thread(s)	You're either going to have to get to the straps with some sort of hook, or take out the seat seat cushion, and move the rear side trim our of the way enough to remove the bolts holding the seatback hinge to go through from under. But on an unrelated note, I was looking at your profile trying to see what year it was for the trunk cylinder to seize from corrosion, and while the year isn't listed, I see you're in toronto with a Kia Rondo... ... Get rid of that hot potato SOON. if you're in canada your cars are subject to rust and those kias have STRUCTURAL FUEL TANKS which are weak to rust, the start to leak from the bottom and cost several thousand dollars to replace.

10-17-2021, 08:55 PM	#10
AJ32162 Member Join Date: Oct 2017 Drives: 2019 BRZ with Performance Package Location: FL Posts: 67 Thanks: 93 Thanked 53 Times in 32 Posts Mentioned: 0 Post(s) Tagged: 0 Thread(s)	This may help it's from a post by Stang70Fastback on another thread. "Grab the black plastic trim surrounding the lock mechanism on the top corner of the rear seatback. Pull it up. It snaps right off. The pull up on the red-colored peg to release the seat. Then just snap the cover back on. It's that simple."

User Name		Remember Me?
Password