WHAT DID YOU DO TO YOUR FRS TODAY?

[beltax90]

Originally Posted by KR-S

So I had some stripes added to my car by 9Livery today and I'm REALLY impressed with how much the pattern matches my TRD fins. Probably the only thing that sucks is that the TRD CF patterns are not as noticeable from afar, but then again perhaps the unintended subtlety is a good thing.

Attachment 191799
Attachment 191800

^ These will probably end up on the antique road show and go for $25,000

[RToyo86]

Installed some faux carbon trim for the center console, and installed the Alcantara overlays for the trim on the knee pad.
I had to cut out some material on the overlay, as the base climate control has a plastic ridge that sticks out near the bottom that the auto climate control does not.

[DarkPira7e]

Mounted my ARC-8s onto the car! Only the front, I need new rear strut mounts and nuts since mine are too rusty to come off.
Can't wait to have it all on the ground with the Sachs dampers and Eibach pro kit!

[JakeP47]

Bought her and joined the club


Sent from my iPhone using Tapatalk

[kevaughan]

Nice FIVE:AD kit! Those are rare. My absolute favorite front lip.

[Mike0110]

[QUOTE=Wally86;3355377]Does rally sport direct not ship to JP?

Thanks for the info, I'll try to contact them !

[Cedric]

Took out my 10 Series badges and replaced them with Toyota Badges.

Before


After


There’s a big hole in the middle of the bumper for the light up badges, but the Toyota badge does an okay job at hiding it. I plan on changing my front bumper and trunk, but it honestly doesn’t bother me too much, and I also have no money at the moment, so I have to live with it anyway.




Sent from my iPhone using Tapatalk Pro

[thekevinvo]

Installed the Grimmspeed Master Cylinder Brace today.

[RToyo86]

Got the last of my interior together.

Black Suede door handles, shifter, knee pad, and upper vent trim.

And some carbon overlays for the door switches, analog clock, a TRD style carbon plaque for the heated seat hole and a carbon hand brake.

Edit

[KR-S]

Originally Posted by RToyo86

Got the last of my interior together.

Black Suede door handles, shifter, knee pad, and upper vent trim.

And some carbon overlays for the door switches, analog clock, a TRD style carbon plaque for the heated seat hole and a carbon hand brake.

Where did you get your phone mount mount? I've been looking for a good solution since I swapped the center and passenger dash to the canadian BRZ piece months ago, and I know I can't just stick a Scoshe on like before without damaging the piece.

[RToyo86]

Originally Posted by KR-S

Where did you get your phone mount mount? I've been looking for a good solution since I swapped the center and passenger dash to the canadian BRZ piece months ago, and I know I can't just stick a Scoshe on like before without damaging the piece.

The bracket was 3D printed for me by a member here. Then I wrapped it and stuck the mount to it.

If you check the "phone mount thread"" on here, you should be able to find all of the info there.

[jflogerzi]

Originally Posted by KR-S

Where did you get your phone mount mount? I've been looking for a good solution since I swapped the center and passenger dash to the canadian BRZ piece months ago, and I know I can't just stick a Scoshe on like before without damaging the piece.

You can buy it. It's based on this I think

https://www.beatsonicusa.com/mobile-...ies/qbf13.html

Sent from my GM1915 using Tapatalk

[KR-S]

Originally Posted by jflogerzi

You can buy it. It's based on this I think

https://www.beatsonicusa.com/mobile-...ies/qbf13.html

Sent from my GM1915 using Tapatalk

Not quite. That phone holder is for two-piece dashes. I recently swapped to a one-piece dash, so there's no more gap in between to insert that mount.

On top of that, I previously had a phone holder from them and found that the rubber grips holding the phone wear down to the point they no longer hold effectively.

[Dave-ROR]

I determined the dash was too heavy so I cut it up to save weight. Maybe.