follow ft86club on our blog, twitter or facebook.
FT86CLUB
Ft86Club
Delicious Tuning
Register Garage Members List Calendar Search Today's Posts Mark Forums Read

Go Back   Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community - FT86CLUB > FT86CLUB Shared Forum > Member's Car Journals

Member's Car Journals Car journals by our members.


User Tag List

Reply
 
Thread Tools Search this Thread
Old 02-10-2024, 10:29 AM   #295
Spuds
The Dictater
 
Spuds's Avatar
 
Join Date: Apr 2017
Drives: '13 Red Scion FRS
Location: MD, USA
Posts: 9,514
Thanks: 26,365
Thanked 12,533 Times in 6,208 Posts
Mentioned: 87 Post(s)
Tagged: 0 Thread(s)
Well, the second round of testing went better than the first.

Ran the car and checked for exhaust leaks with a smoke stick. No leaks when idling cold. No leaks when idling hot, even after poking the throttle. Still SOUNDS like a leak at certain rpms, but it's no longer dumping enough exhaust into the engine bay to cause problems. Fuel trims were fine. This all remains true after a drive so it's fixed enough I guess.

Also confirmed, new black RTV patches at the valve covers aren't oily, so that's working too. Need to get the area real clean before application I guess.

Car on ground, the WL rear endlinks stand straight up when set to the lowest setting + some wiggle room. Better than stock at least due to lowering. Haven't noticed any issues on my drive around but didn't really push it suspension wise. Cannot get a good feel for removing preload as suspected, but they are adjustable on the ground.

Bedded in brakes (Ferodo DS2500 pads and Centric blank rotors) with about 20 consecutive 60mph-20mph applications at ~50%. Actually did it 2 times because the first set I must have been a bit too easy on the brakes and didn't get a consistent deposit on the rotors. Hopefully I didn't overheat them the second as they were smelly when I got back.

The brake feel is very different to stock brakes. The pad grip to heat profile is different which will take some getting used to. It also feels a bit squishy, though I tested it and there's enough stopping power to hit the abs on street tires at least. I might bleed the brakes again and see if that makes the pedal a bit firmer. Might just be how the pads work.

Lol wall o text. Here's a bad picture of endlinks? I'll get a car picture today with the new wheels. Might want to at least wash it first...
Attached Images
 
__________________
If a picture is worth a thousand words, a model is worth ten thousand pictures.
Also: "Build Thread"

Last edited by Spuds; 02-10-2024 at 11:40 AM.
Spuds is offline   Reply With Quote
The Following 6 Users Say Thank You to Spuds For This Useful Post:
gt5759 (02-15-2024), JD001 (06-03-2024), NoHaveMSG (02-10-2024), Racecomp Engineering (02-10-2024), RedReplicant (02-10-2024), Wally86 (04-17-2024)
Old 04-15-2024, 01:00 AM   #296
Spuds
The Dictater
 
Spuds's Avatar
 
Join Date: Apr 2017
Drives: '13 Red Scion FRS
Location: MD, USA
Posts: 9,514
Thanks: 26,365
Thanked 12,533 Times in 6,208 Posts
Mentioned: 87 Post(s)
Tagged: 0 Thread(s)
Gave up and ordered a JDL EL header. Leak got worse again and I've exhausted my options to fix it. Ptuning header might be fine for someone with a straight through exhaust, too much resistance downstream with everything else stock.

Autocross is here! First test and tune with new brakes. DS2500 pads are soooo good, but they are quite dusty. Bleeding didn't make the brakes any stiffer, but I think the give might be a feature of the pad to improve modulation?
Placed OK, I just gotta remember how to go fast again. Didn't get a chance to play with dampers unfortunately. Did take video with my new GoPro.
__________________
If a picture is worth a thousand words, a model is worth ten thousand pictures.
Also: "Build Thread"
Spuds is offline   Reply With Quote
The Following 4 Users Say Thank You to Spuds For This Useful Post:
autoracer86 (04-15-2024), NoHaveMSG (04-15-2024), villainous_frx (04-16-2024), Wally86 (04-17-2024)
Old 04-15-2024, 06:16 AM   #297
autoracer86
Senior Member
 
autoracer86's Avatar
 
Join Date: Jul 2022
Drives: Toyota GT86
Location: Ireland
Posts: 567
Thanks: 506
Thanked 385 Times in 243 Posts
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
I had a bit of extra travel in my brake pedal after my first session on track which I never had before. Like you I still had enough braking power to trigger ABS so I just keep on trucking for the day.

I did just order some temp stickers for the calipers so I can keep a better eye on things... Everyone warned me the CL brake pads I have run hot
autoracer86 is offline   Reply With Quote
The Following 2 Users Say Thank You to autoracer86 For This Useful Post:
Spuds (04-15-2024), Wally86 (04-17-2024)
Old 05-26-2024, 08:14 PM   #298
Spuds
The Dictater
 
Spuds's Avatar
 
Join Date: Apr 2017
Drives: '13 Red Scion FRS
Location: MD, USA
Posts: 9,514
Thanks: 26,365
Thanked 12,533 Times in 6,208 Posts
Mentioned: 87 Post(s)
Tagged: 0 Thread(s)
Now those are some pretty nice pipes right there. Good bye torque dip. My engine bay still feels like it's on fire though.

Stock: 20.6lb. Ptuning: 17.2lb. JDL 14.6lb.
Attached Images
  
__________________
If a picture is worth a thousand words, a model is worth ten thousand pictures.
Also: "Build Thread"
Spuds is offline   Reply With Quote
The Following 3 Users Say Thank You to Spuds For This Useful Post:
NoHaveMSG (05-27-2024), RToyo86 (06-03-2024), villainous_frx (05-27-2024)
Old 06-03-2024, 01:30 PM   #299
gnarjunkie
Member
 
Join Date: Oct 2022
Drives: '23 GR86, '17 BRZ
Location: Colorado
Posts: 79
Thanks: 2
Thanked 53 Times in 30 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by Spuds View Post

Bedded in brakes (Ferodo DS2500 pads and Centric blank rotors) with about 20 consecutive 60mph-20mph applications at ~50%. Actually did it 2 times because the first set I must have been a bit too easy on the brakes and didn't get a consistent deposit on the rotors. Hopefully I didn't overheat them the second as they were smelly when I got back.

The brake feel is very different to stock brakes. The pad grip to heat profile is different which will take some getting used to. It also feels a bit squishy, though I tested it and there's enough stopping power to hit the abs on street tires at least. I might bleed the brakes again and see if that makes the pedal a bit firmer. Might just be how the pads work.

Old post reply but... you definitely want to get the brakes pretty darn hot while bedding. Especially with track-focused brakes. When I bed in the G-Loc R16's I use for the track car, I do 35-5mph a few times to start building heat, and then 60-5mph as close to the ABS threshold as possible. So on the brakes as hard as possible without engaging ABS.

Get back up to 60mph as fast as possible then repeat immediately. Usually around the fourth time they start to feel really good, which is also about the time I start smelling the pads. Then the goal is to cruise until the pads are completely cool without touching the brakes. Not always possible, but it's the goal.

I'm not familiar with Ferodo DS2500's, but if they are track-focused pads then they probably need a good bit of heat to work well and will feel like they need a lot of extra pedal force to work when cold (squishy feeling). If I ever autox on the R16s I drag the brakes the entire way through the grid and up to the start to try to build a bit of heat in them before the run starts, even if I have a co-driver and they're still warm-ish before my lap.
gnarjunkie is offline   Reply With Quote
The Following User Says Thank You to gnarjunkie For This Useful Post:
Spuds (06-03-2024)
Old 06-03-2024, 02:21 PM   #300
JD001
Senior Member
 
JD001's Avatar
 
Join Date: Apr 2015
Drives: Subaru BRZ
Location: UK
Posts: 6,076
Thanks: 7,718
Thanked 6,267 Times in 3,517 Posts
Mentioned: 26 Post(s)
Tagged: 2 Thread(s)
Quote:
Originally Posted by Spuds View Post
Now those are some pretty nice pipes right there. Good bye torque dip. My engine bay still feels like it's on fire though.

Stock: 20.6lb. Ptuning: 17.2lb. JDL 14.6lb.
UEL = no torque dip
EL = is the same as the stock header, no?

BTW, what's happended to @Tcoat?
JD001 is offline   Reply With Quote
Old 06-03-2024, 03:27 PM   #301
Spuds
The Dictater
 
Spuds's Avatar
 
Join Date: Apr 2017
Drives: '13 Red Scion FRS
Location: MD, USA
Posts: 9,514
Thanks: 26,365
Thanked 12,533 Times in 6,208 Posts
Mentioned: 87 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by JD001 View Post
UEL = no torque dip
EL = is the same as the stock header, no?

BTW, what's happended to @Tcoat?
Butt dyno says it's gone.

Idk, I assume he rage quit. Hope he's doing alright.
__________________
If a picture is worth a thousand words, a model is worth ten thousand pictures.
Also: "Build Thread"
Spuds is offline   Reply With Quote
The Following User Says Thank You to Spuds For This Useful Post:
JD001 (06-04-2024)
Old 06-03-2024, 03:46 PM   #302
autoracer86
Senior Member
 
autoracer86's Avatar
 
Join Date: Jul 2022
Drives: Toyota GT86
Location: Ireland
Posts: 567
Thanks: 506
Thanked 385 Times in 243 Posts
Mentioned: 4 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by JD001 View Post
UEL = no torque dip
EL = is the same as the stock header, no?

BTW, what's happended to @Tcoat?
My understanding was EL was for people who wanted to make power and UEL was for people who wanted boxer rumble.
autoracer86 is offline   Reply With Quote
The Following 2 Users Say Thank You to autoracer86 For This Useful Post:
JD001 (06-04-2024), Spuds (06-03-2024)
Old 06-03-2024, 06:13 PM   #303
Spuds
The Dictater
 
Spuds's Avatar
 
Join Date: Apr 2017
Drives: '13 Red Scion FRS
Location: MD, USA
Posts: 9,514
Thanks: 26,365
Thanked 12,533 Times in 6,208 Posts
Mentioned: 87 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by gnarjunkie View Post
Old post reply but... you definitely want to get the brakes pretty darn hot while bedding. Especially with track-focused brakes. When I bed in the G-Loc R16's I use for the track car, I do 35-5mph a few times to start building heat, and then 60-5mph as close to the ABS threshold as possible. So on the brakes as hard as possible without engaging ABS.

Get back up to 60mph as fast as possible then repeat immediately. Usually around the fourth time they start to feel really good, which is also about the time I start smelling the pads. Then the goal is to cruise until the pads are completely cool without touching the brakes. Not always possible, but it's the goal.

I'm not familiar with Ferodo DS2500's, but if they are track-focused pads then they probably need a good bit of heat to work well and will feel like they need a lot of extra pedal force to work when cold (squishy feeling). If I ever autox on the R16s I drag the brakes the entire way through the grid and up to the start to try to build a bit of heat in them before the run starts, even if I have a co-driver and they're still warm-ish before my lap.
Yeah that's basically what I did. The good thing about rural living is there are a bunch of roads with nobody on them at 1am. I would describe DS2500 as a very good street and AX pad. A lot of people have said they don't handle track driving very well.
__________________
If a picture is worth a thousand words, a model is worth ten thousand pictures.
Also: "Build Thread"
Spuds is offline   Reply With Quote
Old 06-03-2024, 06:48 PM   #304
Spuds
The Dictater
 
Spuds's Avatar
 
Join Date: Apr 2017
Drives: '13 Red Scion FRS
Location: MD, USA
Posts: 9,514
Thanks: 26,365
Thanked 12,533 Times in 6,208 Posts
Mentioned: 87 Post(s)
Tagged: 0 Thread(s)
Oh, also got away with my first money shift. Top of second to first, going downhill towards some parking lot curbing I had go between at AX. I was really saved by how long it took me to get the transmission into (the wrong) gear. Caught it as I was releasing the clutch and the rear started kicking out.

Shifting into 3rd with lateral G and driving against the clock is hard guys. Really figured it out on my last run which I proceeded to blow due to getting greedy in the last braking zone ...

Any tricks for making it easier to select the right gear? Short shifter? Or does that make it harder?
__________________
If a picture is worth a thousand words, a model is worth ten thousand pictures.
Also: "Build Thread"
Spuds is offline   Reply With Quote
Old 06-03-2024, 10:38 PM   #305
RToyo86
Senior Member
 
RToyo86's Avatar
 
Join Date: Mar 2018
Drives: 17 Asphalt 86
Location: Ottawa
Posts: 2,238
Thanks: 1,768
Thanked 2,336 Times in 1,180 Posts
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by JD001 View Post
UEL = no torque dip
EL = is the same as the stock header, no?
Depends on the EL header design.
4-1 EL is more top end but retains similar torque curve as oem header. Then you have newer breed of 4-2-1 ELs like the JDL and ace header which bridge the gap and give you flatter torque curve while retaining good top end power.

They seem to prefer more custom calibration vs other headers. I went from Gruppe-S UEL to the JDL EL and the power delivery stayed linear.
Personally don't notice much difference in top end, at the very least having smooth EL sound with no torque penalty is enough for me.
RToyo86 is online now   Reply With Quote
The Following 2 Users Say Thank You to RToyo86 For This Useful Post:
JD001 (06-04-2024), Spuds (06-03-2024)
Old 06-03-2024, 10:43 PM   #306
RToyo86
Senior Member
 
RToyo86's Avatar
 
Join Date: Mar 2018
Drives: 17 Asphalt 86
Location: Ottawa
Posts: 2,238
Thanks: 1,768
Thanked 2,336 Times in 1,180 Posts
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by Spuds View Post
Oh, also got away with my first money shift. Top of second to first, going downhill towards some parking lot curbing I had go between at AX. I was really saved by how long it took me to get the transmission into (the wrong) gear. Caught it as I was releasing the clutch and the rear started kicking out.

Shifting into 3rd with lateral G and driving against the clock is hard guys. Really figured it out on my last run which I proceeded to blow due to getting greedy in the last braking zone ...

Any tricks for making it easier to select the right gear? Short shifter? Or does that make it harder?
Mtec shift springs generally make the shifts feel a bit more snappy which might help.
I wasn't a fan of the torque solutions shifter I tried. Originally with stock shifter bushings, then both front carrier and rear bushing. Shift effort went up and was so tight it made it hard skipping gears on downshifts around town. Kept the bushings and removed the shifter.

I think IRP could be a solution, few friends who track run it and have nothing but good things to say.
RToyo86 is online now   Reply With Quote
The Following User Says Thank You to RToyo86 For This Useful Post:
Spuds (06-03-2024)
Old 06-03-2024, 10:56 PM   #307
Spuds
The Dictater
 
Spuds's Avatar
 
Join Date: Apr 2017
Drives: '13 Red Scion FRS
Location: MD, USA
Posts: 9,514
Thanks: 26,365
Thanked 12,533 Times in 6,208 Posts
Mentioned: 87 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by RToyo86 View Post
Mtec shift springs generally make the shifts feel a bit more snappy which might help.
I wasn't a fan of the torque solutions shifter I tried. Originally with stock shifter bushings, then both front carrier and rear bushing. Shift effort went up and was so tight it made it hard skipping gears on downshifts around town. Kept the bushings and removed the shifter.

I think IRP could be a solution, few friends who track run it and have nothing but good things to say.
Yeah, my main problem was I was hitting the gate prong because I was slightly out of position due to a left-hand turn. Really just need more practice if I'm being honest, but I'll definitely look into those springs, it might help a bit in the 1 or 2 cases I'll need them lol. I think they might be stx legal?

I should look into the irp, heard good things at least.

I do already have a Perrin rear shifter bushing and group N motor and transmission mounts. Definitely help keeping everything in position.
__________________
If a picture is worth a thousand words, a model is worth ten thousand pictures.
Also: "Build Thread"
Spuds is offline   Reply With Quote
The Following User Says Thank You to Spuds For This Useful Post:
villainous_frx (06-04-2024)
Old 06-03-2024, 11:22 PM   #308
gnarjunkie
Member
 
Join Date: Oct 2022
Drives: '23 GR86, '17 BRZ
Location: Colorado
Posts: 79
Thanks: 2
Thanked 53 Times in 30 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
Quote:
Originally Posted by Spuds View Post
Oh, also got away with my first money shift. Top of second to first, going downhill towards some parking lot curbing I had go between at AX. I was really saved by how long it took me to get the transmission into (the wrong) gear. Caught it as I was releasing the clutch and the rear started kicking out.

Shifting into 3rd with lateral G and driving against the clock is hard guys. Really figured it out on my last run which I proceeded to blow due to getting greedy in the last braking zone ...

Any tricks for making it easier to select the right gear? Short shifter? Or does that make it harder?
Oof -- that's scary. Done that a few times myself.

I found that the best is just making sure to not rush the shift. Even in a super hectic autox course there are brief moments where you're pointed straight. I just shift a tiny bit earlier or later to make sure that I shift when there isn't a ton of lateral G's and things to be thinking about.
gnarjunkie is offline   Reply With Quote
The Following User Says Thank You to gnarjunkie For This Useful Post:
Spuds (06-03-2024)
 
Reply

Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
2018 Camaro SS 1LE vs Spuds' FRS Spuds FR-S / BRZ vs.... 13 06-16-2019 10:11 PM
FRS from Vroom - RISKY? Cosa Scion FR-S / Toyota 86 GT86 General Forum 14 10-21-2018 09:27 PM
So my key FOB was put in the washing machine.... Kayzer Soze BRZ First-Gen (2012+) -- General Topics 11 06-07-2013 11:43 AM
Vroom! - This week's blipshift shirt blipshift Miscellaneous 1 11-13-2012 10:29 PM


All times are GMT -4. The time now is 05:35 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
User Alert System provided by Advanced User Tagging v3.3.0 (Lite) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.

Garage vBulletin Plugins by Drive Thru Online, Inc.