WHAT DID YOU DO TO YOUR BRZ TODAY?

[BRZ_88]

Installed a new rear wing.

[MotoX16]

Spent the evening making her look pretty again. Did a wash, clay bar, polished with a scratch and swirl remover, then did a presealant polish, and applied a paint sealant

[Yoshoobaroo]

HERESY



Now the only logo in the engine bay is a TRD logo. I quite enjoy that in some twisted way.

Edit: pictures do not do justice to how much bigger the airbox and filter are than stock:

[dragoontwo]

Getting ready for the weekend.

[weederr33]

Now I just gotta play the waiting game for the paint to cure...

[Breezio]

Started the STX build.

[Breezio]

Nearly finished the STX build. All parts installed and roughly dialed in.
RCE T2's
Vorshlag plates
Verus LCA's
Hotchkis 1" hollow front bar
Hotchkis adjustable endlinks
Openflash UEL header
HKS Hi-Power Spec-L catback
Openflash tune
949 6UL 17x9 wheels
Yokohama A052's, 255/40

-4 camber in front, 0 toe
-2.5 camber in rear, currently 0 toe
Still need to raise the rear about 1/2" and then corner balance.

[JonAvalon]

Mod Monday!

Gruppe-S UEL arrived, the ceramic coating is just lovely! Also installed a Mishimoto PCV catch can and did an oil change with a new Fumoto valve.

[BirdTRD]

Washed, clayed, polished, and waxed.

[wolffbite]

Finally got around to a thorough detail... weather was not cooperating on weekends!

Did the interior last weekend, but today I did:

Wheels off wash to get at the wheel wells
Iron-x Decon
Polished a few oxidized areas and swirls out
Wolfgang Exterior Trim sealant to all plastic
Coat of Soft99 Fusso Coat Dark
Installed paint-matched mudguards (I applied PPF to the inside face beforehand)

This was after getting out for 2 hours of kayaking and getting a nasty sunburn. I'm completely spent and I can tell I will be sore tomorrow, but it sure looks killer!

[CBR600RR]

^ that wheel and tire set up looks amazing on your BRZ!

[norcalpb]

Originally Posted by JonAvalon

Changed wheel setup and installed springs this weekend. Just needs an alignment now but I'm really happy with the results. I was skeptical with the high offset on 245 but my calculations were correct and it's basically equivalent to a 17x9 +38 or +35 setup. Plenty of space between the perch and enough for a BBK.

Eibach Sportline on factory struts
SPC Front bolts and Rear LCA

ESR SR07 17x8.5 +30
245/40 Federal ST-1
Project Kics hardware: Hub rings, valve stems and R40 Iconix lug nuts

Have you noticed any vibrations with the project kics hub adapters? I want to buy them, but the “Subaru” version lists a 56mm bore instead of the 56.1mm that we actually have. I’m sure it can’t make too crazy of a difference, but I am paranoid about that kinda stuff

[JonAvalon]

Originally Posted by norcalpb

Have you noticed any vibrations with the project kics hub adapters? I want to buy them, but the “Subaru” version lists a 56mm bore instead of the 56.1mm that we actually have. I’m sure it can’t make too crazy of a difference, but I am paranoid about that kinda stuff

Nope none at all, it's been good so far. Yea that confused me as well when I was buying them, but it seems like just list the whole number instead of putting the ".1 etc" for any of the sizes. It fit just like any other hub ring with no issues.

[spcmafia]

Got my 18 BRZ about a month ago, and it wasnt long until I started throwing money at the car like a horny 18 year old soldier, at the strip club, straight out from basic.
Last week after a long wait on parts I ordered, I got a K&N drop filter, Perrin Inlet Hose, Perrin Rear Shifter Bushing (Amazing), Changed LSD/Trans fluids with Motul, Invidia Q300 catback with a HKS double Resonated Frontpipe, and finally got my OFT Stage One tune.

I decided that I can't know that I'm broke if I don't look into my bank account. Do I regret it? Absolutely not. I'm in love with this car.