01-30-2023, 07:22 AM | #1 |
Junior Member
Join Date: Jan 2022
Drives: 2014 Subaru BRZ
Location: Hawaii
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
ECUTek Error
Anyone else having the issue of ECUTek giving the error "Timeout waiting for batch" when connected via Bluetooth? It gives this error when I bring up the dashboard. Sometimes it works for a while, other times it will error out after a few seconds and go back to the main screen. I get the same error on my phone or the headunit. I couldn't find anything searching through the forums or on google.
|
01-30-2023, 08:27 AM | #2 |
Senior Member
Join Date: Jan 2017
Drives: brz 2017 hksv2
Location: italy
Posts: 2,196
Thanks: 500
Thanked 1,067 Times in 775 Posts
Mentioned: 65 Post(s)
Tagged: 0 Thread(s)
|
it s the obd interface that is losing connection with the pin, common defect of your MY
Try to bend Pins a little or use an extension, they are cheap |
01-30-2023, 08:48 AM | #3 |
Junior Member
Join Date: Jan 2022
Drives: 2014 Subaru BRZ
Location: Hawaii
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Looking at the Dongle and all the pins seem to be straight. There are 2 pins in the center that protrude further out than the rest though... Is that normal?
Last edited by mudda502; 01-30-2023 at 09:05 AM. |
01-30-2023, 10:27 AM | #4 |
Senior Member
Join Date: Jan 2017
Drives: brz 2017 hksv2
Location: italy
Posts: 2,196
Thanks: 500
Thanked 1,067 Times in 775 Posts
Mentioned: 65 Post(s)
Tagged: 0 Thread(s)
|
the problem is not the dongle per se
the problem is the quality of your vehicle 's obd port It tends to make. this problem, either you fix it someway bending things, or if you have luck an extension is sufficient Best way is to swap directly the obd Port with a newer one Last edited by tomm.brz; 01-30-2023 at 11:35 AM. |
01-30-2023, 11:08 AM | #5 |
Junior Member
Join Date: Jan 2022
Drives: 2014 Subaru BRZ
Location: Hawaii
Posts: 3
Thanks: 0
Thanked 0 Times in 0 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
I'll have to check the port then. Hopefully its just a loose connection that I can fix easy. Thanks for your help.
|
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Ecutek error while reflashing ecu | TOUGEerrDay | Software Tuning | 6 | 12-28-2016 11:34 AM |
Ecutek map access error | CaptivaBlueTeg | Software Tuning | 2 | 10-29-2016 12:57 PM |
ECUTek Cable has OBD Error when Attempting to Log | Cross | Software Tuning | 5 | 02-05-2016 02:22 PM |
ECUtek reflashing error | Kwaziekeller | Software Tuning | 4 | 08-04-2014 11:36 PM |
ECUtek error 37 | NickFRS | Software Tuning | 5 | 06-29-2014 04:14 PM |