|
||||||
| Engine, Exhaust, Transmission Discuss the FR-S | 86 | BRZ engine, exhaust and drivetrain. |
 |
|
|
Thread Tools | Search this Thread |
01-10-2013, 12:45 AM
|
#1 |
|
Sarcastic SOB
Join Date: May 2012
Drives: '13 FR-S M6, '23 Volvo V60 CC
Location: Thornhill Ontario
Posts: 4,614
Thanks: 1,344
Thanked 2,844 Times in 1,635 Posts
Mentioned: 32 Post(s)
Tagged: 3 Thread(s)
|
Cusco catch can install
Nice looking unit, very clean mounting.
So, realizing the Japanese installation instructions are for the crankcase vent to after air filter...NOT what it is supposed to vent, the PCV valve to intake manifold. Anyway if anyone else has installed this unit can corroborate this is correct? I cut the supplied hose in 2 pieces. Question concerning securing 15mm supplied pipe to 9mm PCV valve outlet. What are we supposed to use to connect? Perhaps the incorrect Cusco instructions show they rushed to market.
__________________
5:AD kit, HKS V1+ S/C, ECUtek dyno'd, Ohlins MP20, Magnaflow cb, Revworks UEL, Topspeed overpipe, Pinnacle Ceramic tint, VG shark fin, HID's, yellow DRL's, full LEDs, red floor lights, Homelink mirror, trunk lid liner, Perrin LWCP, Valenti smoked, Flossy Grip Tape Shorty, GT86 plaque, lighted vanity mirror, Michelin PSS, Project mU +800, DOT4 fluid, 720 Form GTF1 17x8&9, stitched leather bits, EZ valve.
Last edited by wbradley; 01-10-2013 at 10:53 AM. |
|
|
|
01-10-2013, 08:18 PM
|
#2 |
|
Kouki-Monster
Join Date: May 2012
Drives: 2013 Scion FR-S
Location: Saskatoon, SK
Posts: 1,137
Thanks: 11
Thanked 562 Times in 261 Posts
Mentioned: 6 Post(s)
Tagged: 0 Thread(s)
|
comes with a little pvc/plastic tube that mates the 15mm hose to the factory hose
__________________
Rich Anderson
EMPOWER AUTO |
|
|
|
|
01-11-2013, 12:11 AM
|
#3 |
|
Sarcastic SOB
Join Date: May 2012
Drives: '13 FR-S M6, '23 Volvo V60 CC
Location: Thornhill Ontario
Posts: 4,614
Thanks: 1,344
Thanked 2,844 Times in 1,635 Posts
Mentioned: 32 Post(s)
Tagged: 3 Thread(s)
|
Mating the molded rubber OEM PCV vent tube to a run of Cusco supplied 15mm tubing is too long to the catch can. I want the Cusco tube direct to PCV valve. For now I used a part of the bark tube to do the job.
__________________
5:AD kit, HKS V1+ S/C, ECUtek dyno'd, Ohlins MP20, Magnaflow cb, Revworks UEL, Topspeed overpipe, Pinnacle Ceramic tint, VG shark fin, HID's, yellow DRL's, full LEDs, red floor lights, Homelink mirror, trunk lid liner, Perrin LWCP, Valenti smoked, Flossy Grip Tape Shorty, GT86 plaque, lighted vanity mirror, Michelin PSS, Project mU +800, DOT4 fluid, 720 Form GTF1 17x8&9, stitched leather bits, EZ valve.
|
|
|
|
|
|
|
|
|
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Anyone been able to install Cusco drift button? | cobrabyte | Cosmetic Modification (Interior/Exterior/Lighting) | 36 | 09-12-2013 04:42 PM |
| AP Pulley - Cusco Oil Catch Can | TeamSweet86 | Engine, Exhaust, Bolt-Ons | 9 | 02-22-2013 01:25 PM |
| AVO Inlets, Injen Intakes, Cusco Catch Cans, All In Stock! | RallySport Direct | Engine, Exhaust, Bolt-Ons | 3 | 10-05-2012 12:39 AM |
| Cusco Oil Catch Can for BRZ/FR-S at Redline360 | Redline360 | Engine, Exhaust, Bolt-Ons | 0 | 07-01-2012 03:16 AM |
| Cusco Street Oil Catch Tank 0.6L in stock!!! | IslandImportPerformance | Engine, Exhaust, Bolt-Ons | 0 | 06-05-2012 12:56 AM |
