|
Software Tuning Discuss all software tuning topics. |
|
Thread Tools | Search this Thread |
06-24-2020, 04:05 PM | #1 |
Senior Member
Join Date: Aug 2018
Drives: turbo frs
Location: worldwide
Posts: 173
Thanks: 122
Thanked 8 Times in 7 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
grimmspeed ebcs brz install????
Dear all
I need good setup For grimmspeed EBCS WITH EXTERNAL WATEGATE WITH BOOST GAGE car tuned by ecuTek What your recommendation for Port 1.2.3 And where I have to put the T for boost gage Thanks |
06-24-2020, 04:26 PM | #2 |
Rust bucket enthusiast
Join Date: Feb 2017
Drives: 2013 Turbo Firestorm FRS
Location: Vermont
Posts: 3,934
Thanks: 3,200
Thanked 4,095 Times in 2,045 Posts
Mentioned: 31 Post(s)
Tagged: 0 Thread(s)
|
I put the T for the boost gauge before the bump in the line ( T goes on the engine side) going to the brake booster.
These can be confusing, but I have mine set up so the port on the FRONT is going to the compressor housing, the port on the left (EBCS oriented with the front port facing you and the ports on the bottom half) connected to the wastegate. 3rd port ( on the right) has a muffler on it. Mine is NOT a branded Grimmspeed EBCS< it is a Mac 3 port valve Last edited by DarkPira7e; 06-24-2020 at 05:21 PM. |
The Following User Says Thank You to DarkPira7e For This Useful Post: | gt7877 (06-24-2020) |
06-24-2020, 04:28 PM | #3 |
Senior Member
Join Date: Aug 2018
Drives: turbo frs
Location: worldwide
Posts: 173
Thanks: 122
Thanked 8 Times in 7 Posts
Mentioned: 0 Post(s)
Tagged: 0 Thread(s)
|
Can you please explain with diagram or image
|
06-24-2020, 04:36 PM | #4 |
Rust bucket enthusiast
Join Date: Feb 2017
Drives: 2013 Turbo Firestorm FRS
Location: Vermont
Posts: 3,934
Thanks: 3,200
Thanked 4,095 Times in 2,045 Posts
Mentioned: 31 Post(s)
Tagged: 0 Thread(s)
|
WG - WASTEGATE T - Turbo compressor housing. I don't have a photo of where I tapped for boost gauge. Start at the brake booster and work your way down the vacuum line. 4" in you'll feel a hard piece. 1" after that is where I put a T |
06-24-2020, 05:20 PM | #5 |
Rust bucket enthusiast
Join Date: Feb 2017
Drives: 2013 Turbo Firestorm FRS
Location: Vermont
Posts: 3,934
Thanks: 3,200
Thanked 4,095 Times in 2,045 Posts
Mentioned: 31 Post(s)
Tagged: 0 Thread(s)
|
Just got done work. Here's one fresh from the garage. Be sure if you use a T to try and get a tapered T fitting. |
The Following User Says Thank You to DarkPira7e For This Useful Post: | gt7877 (06-24-2020) |
|
|
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
EBCS options | wise345 | Forced Induction | 4 | 12-02-2016 05:21 PM |
Grimmspeed EBCS | TheLaughingMan | Forced Induction | 9 | 08-05-2016 09:39 PM |
Grimmspeed EBCS | lbroskee | Engine, Exhaust, Bolt-Ons | 1 | 05-06-2016 07:10 PM |
EBCS set up options | Brick | Software Tuning | 17 | 04-13-2014 06:48 PM |
EBCS vs MBC | gdrider77 | Forced Induction | 17 | 02-05-2014 10:30 AM |