11-20-2014, 07:45 AM | #113 |
Senior Member
Join Date: Jun 2013
Drives: FR-S
Location: TN
Posts: 569
Thanks: 133
Thanked 174 Times in 126 Posts
Mentioned: 5 Post(s)
Tagged: 1 Thread(s)
|
And there is no smartphone add on device coming right? I was kinda waiting for it but it seems its not gonna be available any soon.
|
11-24-2014, 12:03 PM | #114 |
Senior Member
Join Date: Aug 2012
Drives: Asphalt Grey FR-S
Location: MI
Posts: 102
Thanks: 108
Thanked 17 Times in 15 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Quote:
__________________
2013 Asphalt Grey FR-S MT VIN: 7086XX
Last edited by XtremeMaC; 11-24-2014 at 04:02 PM. |
11-24-2014, 12:58 PM | #115 | |
Senior Member
Join Date: Aug 2012
Drives: Asphalt Grey FR-S
Location: MI
Posts: 102
Thanks: 108
Thanked 17 Times in 15 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Quote:
87 and 86-12 volts constant Did you use 1 fuse tap for this or 2? 85-red and black wire from the brain (trunk release wire) ok 87a-cut trunk motor wire(car side) Not sure what this is, is this on the table below? 30-cut trunk motor wire (trunk side) Where can I find this one The white wire from the brain is not used.ok Thank you!
__________________
2013 Asphalt Grey FR-S MT VIN: 7086XX
Last edited by XtremeMaC; 11-24-2014 at 04:03 PM. |
|
11-24-2014, 08:11 PM | #116 | |
Senior Member
Join Date: Nov 2012
Drives: Whiteout FRS
Location: Florida
Posts: 325
Thanks: 150
Thanked 272 Times in 120 Posts
Mentioned: 8 Post(s)
Tagged: 1 Thread(s)
|
Quote:
That harness plugged directly into the brain, and then the black and red wires are soldered to the wires coming from the handle. Either they have changed the harnesses that come with it and those wires are somewhere else, or they forgot to include it. |
|
11-24-2014, 08:21 PM | #117 | |
Senior Member
Join Date: Nov 2012
Drives: Whiteout FRS
Location: Florida
Posts: 325
Thanks: 150
Thanked 272 Times in 120 Posts
Mentioned: 8 Post(s)
Tagged: 1 Thread(s)
|
Quote:
The trunk release is the brown one (I think, it's been a while), coming out of pin 4 on the HD1 connector. Basically you have to cut that wire (do it a ways out from the pin to the yourself some slack). Then, the end running into the HD1 connector is the car side, the other other end is the trunk side. I think I only used one fuse tap and just used it as the 12 volt source for both. Just be sure you tap a fuse which is always hot so the trunk will open when the car is off. |
|
11-24-2014, 08:48 PM | #118 | |
Senior Member
Join Date: Aug 2012
Drives: Asphalt Grey FR-S
Location: MI
Posts: 102
Thanks: 108
Thanked 17 Times in 15 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
Quote:
Maybe this one?: Also, the guide suggest putting the antenna's in the A pillar, where an airbag exists. Where did you guys place the antennas. I'll open the A pillar cover and see if there is available space away from the airbags.
__________________
2013 Asphalt Grey FR-S MT VIN: 7086XX
|
|
11-24-2014, 08:53 PM | #119 |
Senior Member
Join Date: Nov 2012
Drives: Whiteout FRS
Location: Florida
Posts: 325
Thanks: 150
Thanked 272 Times in 120 Posts
Mentioned: 8 Post(s)
Tagged: 1 Thread(s)
|
As you are looking down on it on that picture, it is connected in the left side, two slots from the top. I think.
|
11-24-2014, 09:35 PM | #120 |
Senior Member
Join Date: Aug 2012
Drives: Asphalt Grey FR-S
Location: MI
Posts: 102
Thanks: 108
Thanked 17 Times in 15 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
ow wow, I somehow totally put that harness aside because it said GPS module.
Right I have the harness, it mounts to 1st one on the left. Thanks man! I will add few pictures to anyone interested in this thread I guess over the weekend. couldn't finish it this weekend...
__________________
2013 Asphalt Grey FR-S MT VIN: 7086XX
Last edited by XtremeMaC; 08-03-2015 at 04:08 PM. |
11-29-2014, 09:53 PM | #121 |
Senior Member
Join Date: Aug 2012
Drives: Asphalt Grey FR-S
Location: MI
Posts: 102
Thanks: 108
Thanked 17 Times in 15 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
finished the install... nothing's working... don't quite get why. I've emailed the tech support. will see if they respond...
I'm trying to deduct the bare minimum cabling needed just for the start/stop to work to see if the brain is even functional. should have done it prior soldering. trusted too much that nothing would go wrong... well, at least good soldering practice, and good exercise to fit underneath the steering wheel. I've taken picture as I went along. once I get it to function *fingers crossed* I'll post few pictures that can be supplementary to the thread. in the meanwhile do you guys have any suggestions as to what I could try to get things working?
__________________
2013 Asphalt Grey FR-S MT VIN: 7086XX
|
11-29-2014, 10:48 PM | #122 |
Senior Member
Join Date: Nov 2012
Drives: Whiteout FRS
Location: Florida
Posts: 325
Thanks: 150
Thanked 272 Times in 120 Posts
Mentioned: 8 Post(s)
Tagged: 1 Thread(s)
|
Hard to say without more info. Does the button light up at all? Have you tested everything with a volt meter to see if there is power running to the brain?
|
12-01-2014, 12:10 PM | #123 |
Senior Member
Join Date: Aug 2012
Drives: Asphalt Grey FR-S
Location: MI
Posts: 102
Thanks: 108
Thanked 17 Times in 15 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
well stupid me, I had not hooked up the ground
now remote start works, start/stop button works. door lock/unlock does not work. I've checked the cables again and again I'm 100% sure the door lock unlock wires are correct. I'm checking to see if Door Trigger is somehow wrong. it is correct according to the table on OP's post. Scytek seems to be working, mini fuse tap I suppose is correct. I get a little (+) mV reading out of it. Not sure what exactly I need to get there. I'll check the manual. the horn works so good that I am about to rip it out. annoying as hell trying to figure out the lock/unlock haven't even touched Trunk release yet. not as important at the moment...do I need this to get the door lock/unlock to work? i figured not.. right? don't really wanna go to the dealer with this. I need to figure out the locks! *sigh*
__________________
2013 Asphalt Grey FR-S MT VIN: 7086XX
|
12-01-2014, 12:25 PM | #124 |
Been Here A While
Join Date: Jan 2013
Drives: 2013 Scion FR-S/ Whiteout
Location: Panama City Beach, FL
Posts: 152
Thanks: 44
Thanked 32 Times in 20 Posts
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
|
Does the immobilizer bypass work with your valet keys? My issue is with the immobilizer. Keeps clicking like it's not hooked up. Is there a way to test to see if that piece is possibly dead? I've used my valet and spare key with the same result of the immobilizer constantly clicking and killing my battery.
|
12-01-2014, 01:03 PM | #125 |
Senior Member
Join Date: Aug 2012
Drives: Asphalt Grey FR-S
Location: MI
Posts: 102
Thanks: 108
Thanked 17 Times in 15 Posts
Mentioned: 2 Post(s)
Tagged: 0 Thread(s)
|
well yes. I placed the original valet key into the immobilizer box. then I placed the duplicate key that I had made into the ignition as instructed. did you wrap that coil around the ignition? I first hold it with my hands to see if it was working. after I concur I wrapped it around with electrical tape.
__________________
2013 Asphalt Grey FR-S MT VIN: 7086XX
|
12-01-2014, 01:43 PM | #126 |
Been Here A While
Join Date: Jan 2013
Drives: 2013 Scion FR-S/ Whiteout
Location: Panama City Beach, FL
Posts: 152
Thanks: 44
Thanked 32 Times in 20 Posts
Mentioned: 15 Post(s)
Tagged: 0 Thread(s)
|
Sure did. I wrapped it and I've held it with the same results. The duplicate key is in the on position right? I've tried it every which way.
|
|
|
Tags |
easygo, remote start |
Thread Tools | Search this Thread |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
STI Push Button Start | Proud of BOXER | Cosmetic Modification (Interior/Exterior/Lighting) | 117 | 08-05-2019 05:19 PM |
Push Button start... | usptwins | DIY (Do-It-Yourself) Guides | 155 | 07-31-2019 11:10 AM |
Q: push button start frs | blanco | Electronics | Audio | NAV | Infotainment | 8 | 08-09-2013 04:58 PM |
BRZ STI push to start button | notFRS | Interior Parts (Incl. Lighting) | 4 | 04-24-2013 12:24 PM |
TRD push start button | nix | Australia Classifieds | 1 | 11-27-2012 12:53 AM |