Open Flash Tablet - OFT TIPS Trick’s & FAQ - Page 77 - Toyota GR86, 86, FR-S and Subaru BRZ Forum & Owners Community

steve99 · 07-16-2017, 08:17 PM

Quote:

Originally Posted by PDXsuperfly

I went ahead and tried to do a 3rd gear WOT but ran out of room before I could get to redline. BTW this is on 92oct OFT & OFH using the OFH tune. I just got a K&N drop in filter so after I read up on tuning and logging I will be doing another. I realized how little I know about tuning and the OFT has got me really interested in learning more...

looks ok up to arround 5500 , you just start to get a tiny bit of knock. Be interested to see a run to redline as they do add a bit of timing past 5500 compared to standard tune.

your 92 must be pretty good quality

looks much better than i thought it would :-)

n0thing · 07-27-2017, 07:08 PM

I have updated my OFT template to allow logging of throttle position, brake pressure, steering angle, gear selection etc, and have exported the csv file. If I use HLT/Racechrono as a laptimer to record the GPS value and export this to another csv file, how can I integrate both datalogs to dashware to compile a video? How do I sync both datalog csv files?

PDXsuperfly · 08-14-2017, 12:19 AM

Quote:

Originally Posted by steve99

looks ok up to arround 5500 , you just start to get a tiny bit of knock. Be interested to see a run to redline as they do add a bit of timing past 5500 compared to standard tune.

So things have gotten a little interesting... I ended up with a drop in K&N filter and a Perrin unresonated 2.5" exhaust. Here is a 1st to 2nd pull at WOT. Still have to get some time to learn about all this data but figured I'd share and hear your thoughts.

steve99 · 08-14-2017, 01:09 AM

Quote:

Originally Posted by PDXsuperfly

So things have gotten a little interesting... I ended up with a drop in K&N filter and a Perrin unresonated 2.5" exhaust. Here is a 1st to 2nd pull at WOT. Still have to get some time to learn about all this data but figured I'd share and hear your thoughts.

looks ok from what you can see

try a 3rd gear pull

also load up the logs to www.datazap.me and just post link, heaps easier to read

Nobunnyhere.86 · 08-22-2017, 06:16 PM

could someone read this upload and let me know if you see anything that i should be worried about? i am new here and still need some learning

My FLKC shows -5 most of the time and when i opened it on OFM it said -100?

Nobunnyhere.86 · 08-22-2017, 06:28 PM

could someone read this upload and let me know if you see anything that i should be worried about? i am new here and still need some learning

My FLKC shows -5 most of the time and when i opened it on OFM it said -100?

jvincent · 08-22-2017, 06:38 PM

Quote:

Originally Posted by TwistedGray

1. I would like to get rid of the flat torque curve around 4000rpm.

You can minimize the dip if you get a catless header but with just a Stage 1 tune there is not a lot of change.

TwistedGray · 08-22-2017, 06:41 PM

Quote:

Originally Posted by jvincent

You can minimize the dip if you get a catless header but with just a Stage 1 tune there is not a lot of change.

Really don't want to put a header on it, but it's good to know that it won't really do much for me. Maybe I'll put it back up on here for sale. Thanks!

jvincent · 08-22-2017, 06:43 PM

Somewhere there is a plot of stock vs stage 1 vs stage 2 on here. Have a look for that.

EDIT: Found it.

http://www.ft86club.com/forums/showp...&postcount=189

TwistedGray · 08-22-2017, 06:54 PM

Quote:

Originally Posted by jvincent

Somewhere there is a plot of stock vs stage 1 vs stage 2 on here. Have a look for that.

EDIT: Found it.

http://www.ft86club.com/forums/showp...&postcount=189

Yeah I saw that which prompted me to buy the OFT

$400 isn't bad for the gains, in my opinion, without having to swap any physical parts. Seemed like a reasonable deal.

Edit: Is my method correct, though? In regards to the launch control settings.

TwistedGray · 08-22-2017, 06:57 PM

Quote:

Originally Posted by TwistedGray

Pardon the very long, thorough post, but I obviously want to make sure I don't brick the unit nor muck something up.

I did make one mistake for sure. I did ALL of this before marrying the device to my car, and after I did that the default files are now "Stg1 A01C.bin" instead of the one I noted before.

So, it would seem that I need to go back and edit the "Stg1 A01C.bin" files instead of using the "Stg 1 D00C.bin" files. Does that sound correct?

jvincent · 08-22-2017, 07:05 PM

Yes. You need to connect the OFT to the car first to get the correct ROM version.

TwistedGray · 08-22-2017, 07:05 PM

Quote:

Originally Posted by jvincent

Yes. You need to connect the OFT to the car first to get the correct ROM version.

Got it, well I think I'm good to go then after I edit the new files.

TwistedGray · 08-22-2017, 07:55 PM

Okay, so I am sure I have done some minor mistake, but I cannot quite figure out what it is. I took a bunch of screenshots of the software as I was going along, so hopefully this helps explain things.

I connected the OFT to the PC and ran it through all the updates. Thereafter, I connected it to the car, read the car's stock ECU, and now I am back on the PC. I want to send a few launch control based files to the OFT, but I need to of course modify the files.

I will only use Stage 1, 91 octane files for my tune(s) with varying launch control RPMs. Otherwise, all other settings will remain as-is.

First step was to connect the OFT to the software, and on the side I would run the RomRaider. I know that I need to add the appropriate Definition file to RomRaider, but this is where I am a little confused as to which of the two files I should use? So, I started with the first one as it matched the naming in the CAL box.

I then navigated to the appropriate Stage 1, 91 octane folder, and proceeded to select the matching file that populated in the OFT software. When doing so, I got this error in RomRaider.

Okay, then I figured I should use the other file (see the first picture), so I first removed the first file and then added the second file.

Back to the Stage 1 folder, selected that file again, and I was hit with some Checksum errors. Per the FAQ this is not a major concern, so onward we go.

I then went in to Launch Control setting and set the parameters to what I want. In this case I want the max RPM set to 2000 thus entered in 5600.

Thereafter, I went to save the file and was again prompted by two errors.

Back to the Openflash Manager software. I clicked the Upload Data button, deleted one of the storage spots.

After that I added in the tune that I just created from RomRaider, but I was immediately hit by this error and could not proceed.

I repeated these steps several times, and I always get hit with that error at the end which prevents me from doing anything.

Any suggestions would be greatly appreciated.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
WTB: Open Flash Tablet	TOZER	Canada Classifieds	3	07-05-2015 07:13 PM
Open Flash Header & Open Flash Tablet	Calavera	Engine, Exhaust, Bolt-Ons	9	05-11-2015 08:27 PM
FS: open flash headers / open flash tablet - SOLD	alanhung85	Canada Classifieds	12	02-10-2015 02:08 PM
FS: Open Flash Tablet (OFT)	mex2309	Engine, Exhaust, Bolt-Ons	1	10-29-2014 02:49 PM
Open flash tablet.	cooldandani	Scion FR-S / Toyota 86 GT86 General Forum	1	02-22-2014 07:14 PM

07-27-2017, 07:08 PM	#1066
n0thing Senior Member Join Date: Jan 2014 Drives: Subaru BRZ Location: Markham Posts: 394 Thanks: 48 Thanked 90 Times in 53 Posts Mentioned: 6 Post(s) Tagged: 0 Thread(s)	I have updated my OFT template to allow logging of throttle position, brake pressure, steering angle, gear selection etc, and have exported the csv file. If I use HLT/Racechrono as a laptimer to record the GPS value and export this to another csv file, how can I integrate both datalogs to dashware to compile a video? How do I sync both datalog csv files?

08-22-2017, 06:43 PM	#1073
jvincent Senior Member Join Date: Sep 2013 Drives: 2022 WRB BRZ Sport-Tech Location: Ottawa, Canada Posts: 1,746 Thanks: 131 Thanked 1,410 Times in 715 Posts Mentioned: 25 Post(s) Tagged: 2 Thread(s)	Somewhere there is a plot of stock vs stage 1 vs stage 2 on here. Have a look for that. EDIT: Found it. http://www.ft86club.com/forums/showp...&postcount=189

08-22-2017, 07:05 PM	#1076
jvincent Senior Member Join Date: Sep 2013 Drives: 2022 WRB BRZ Sport-Tech Location: Ottawa, Canada Posts: 1,746 Thanks: 131 Thanked 1,410 Times in 715 Posts Mentioned: 25 Post(s) Tagged: 2 Thread(s)	Yes. You need to connect the OFT to the car first to get the correct ROM version.

08-22-2017, 07:55 PM	#1078
TwistedGray IG thomas50shades Join Date: Aug 2017 Drives: ISO: BRZ Location: Monterey Bay, CA Posts: 199 Thanks: 7 Thanked 47 Times in 40 Posts Mentioned: 1 Post(s) Tagged: 0 Thread(s)	Okay, so I am sure I have done some minor mistake, but I cannot quite figure out what it is. I took a bunch of screenshots of the software as I was going along, so hopefully this helps explain things. I connected the OFT to the PC and ran it through all the updates. Thereafter, I connected it to the car, read the car's stock ECU, and now I am back on the PC. I want to send a few launch control based files to the OFT, but I need to of course modify the files. I will only use Stage 1, 91 octane files for my tune(s) with varying launch control RPMs. Otherwise, all other settings will remain as-is. First step was to connect the OFT to the software, and on the side I would run the RomRaider. I know that I need to add the appropriate Definition file to RomRaider, but this is where I am a little confused as to which of the two files I should use? So, I started with the first one as it matched the naming in the CAL box. I then navigated to the appropriate Stage 1, 91 octane folder, and proceeded to select the matching file that populated in the OFT software. When doing so, I got this error in RomRaider. Okay, then I figured I should use the other file (see the first picture), so I first removed the first file and then added the second file. Back to the Stage 1 folder, selected that file again, and I was hit with some Checksum errors. Per the FAQ this is not a major concern, so onward we go. I then went in to Launch Control setting and set the parameters to what I want. In this case I want the max RPM set to 2000 thus entered in 5600. Thereafter, I went to save the file and was again prompted by two errors. Back to the Openflash Manager software. I clicked the Upload Data button, deleted one of the storage spots. After that I added in the tune that I just created from RomRaider, but I was immediately hit by this error and could not proceed. I repeated these steps several times, and I always get hit with that error at the end which prevents me from doing anything. Any suggestions would be greatly appreciated.

User Name		Remember Me?
Password